2.3 Output Connections ..................5 2.4 LED Indicators ....................6 2.5 Volume Control ....................7 2.6 Notes ........................8 Chapter 3. Electrical Characteristics ................10 Chapter 4. Mechanical Drawing ..................11 Chapter 5. Contact Us ..................... 12 AA-AB31241 _Ver1.0 _Page i 2004-2012 Sure Electronics Inc.
Page 3
1 X 600Watt Class D Audio Amplifier Board – TAS5630 Note: Please read this manual carefully before you use the product. To keep the product in a best working condition and having a long service time, please operate it according to the relevant steps. The warranty lapses if the product is damaged because of incorrect use and your negligence.
Page 4
1*600WATT CLASS D AUDIO AMPLIFIERBOARD –TAS5630 USER’S GUIDE NOTES: : Product Version Ver 1.0 : Document Version Ver 1.0 AA-AB31241 _Ver1.0 _Page 2004-2012 Sure Electronics Inc.
USER’S GUIDE Chapter 1. Overview Overview Welcome to use this 1*600W Class-D audio amplifier board series by Sure Electronics. It integrates TI’s high performance TAS5630 supporting single channel audio amplification. Single channel is capable of outputting nominal power simultaneously and continuously.
1 X 600Watt Class D Audio Amplifier Board – TAS5630 Ÿ Click & Pop Noise Reduction Ÿ 2 speed Fan. Speeding up when the temperature of the chip rises above 125 centigrade. If the fault condition persists, the protection circuit stays in shutdown until Note: the fault is removed.
Page 7
It’s suggested to make sure the polarity of the wires first and then connect the audio cables, wires. Turn down the output to the lowest and then power the board. 2004-2012 Sure Electronics Inc. AA-AB31241 _Ver1.0_Page 3...
1 X 600WATT CLASS D AUDIO AMPLIFIER BOARD – TAS5630 USER’S GUIDE Chapter 2. Hardware Detail 2.1 Power Connection To power the amplifier board, use either jack J6 or terminal blocks J5. Pay attention to the polarity when connecting power supply.
Terminal Blocks (Optional) J1 Note: You are allowed to feed only one signal to the amplifier board at a time. 2.3 Output Connections You can use either terminal blocks or banana connectors(optional) to output audio signal. 2004-2012 Sure Electronics Inc. AA-AB31241 _Ver1.0_Page 5...
This amplifier has 2 power LED indicator which is marked as “PWR (D2)” and “125 degree C(D4) “. “Power (D2)” will be illuminated in green when power-up. “125 degree C (D4) “will be illuminated once the temperature of TAS5630 reaches up to 125 degrees centigrade, at the same time the fan speeds up.
TABLE 3-1 ELECTRICAL CHARACTERISTICS Never adjust the gains when the amplifier is working, or TAS5630 will be damaged because of the instantaneous voltage. The instantaneous energy will exceed the rated power of a speaker and damage it. When adjust gain, please set SW1, SW2, SW3 and SW4 in the same way to make sure the same gains.
1 X 600Watt Class D Audio Amplifier Board – TAS5630 FIGURE 2-5 VOLUME CONTROL TABLE 2-8 DIP SWITCH SETTING Switch Gain Status(dB) Weak SW1, SW2 Medium High 2.6 Notes In order to protect amplifier board and extend its service lifetime, please read the...
Page 13
In order to protect amplifier and speaker, please turn the volume output to the minimum when hooking up the amplifier and you may readjust the volume when you are sure that the amplifier is functioning properly. 2004-2012 Sure Electronics Inc. AA-AB31241 _Ver1.0_Page 9...
AMPLIFIER BOARD - TDA7498 USER’S GUIDE Chapter 3. Electrical Characteristics Following table lists all typical data of the Amp board. For full specification, please refer to the data sheet of TI’s TAS5630 chip. TABLE 3-1 ELECTRICAL CHARACTERISTICS Parameter Condition Min.
1 X 600WATT CLASS D AUDIO AMPLIFIER BOARD - TDA7498 USER’S GUIDE Chapter 5. Contact Us Sure Electronics Co., Ltd. East zone, 3F, Building 6 Jingang Technology Innovation Center No.108 Ganjiabian Rd (ZIP: 210000) Qixia District Nanjing P.R.China Tel: +86-25-68154800-860...