Table of Contents
Advertisement
7 RECORDING
7-1 Preparation
REC
STOP/EJECT
REVERSE
REW
Connection
Make sure the input/output connectors on the rear panel
are properly connected. For details, refer to
"CONNECTIONS" on page 11 to 13.
Menu switch setting
Set the function menu switches as required.
5
<POSITION> ... Factory setting: L-UP
• Sets the position of the on-screen time/date and
recording mode display. Select one of the four corners
of the screen. (Refer to page 18.)
5
<AUTO REC> ... Factory setting: OFF
• Set to ON to execute timer recording using a
commercially available external timer or to
automatically resume recording when power is
restored after a power failure.
• For details, refer to "How To Restore Recording
After Power Failure" and "External Timer Recording"
on page 37.
5
<REC CHECK> ... Factory setting: MANUAL
Selects between manual and automatic Recording
Check operation. (Refer to page 18.)
5
<TAPE END MODE> ... Factory setting: STOP
Selects the mode engaged when the tape ends during
recording. (Refer to page 18.)
5
<INDEX AL/SKIP> ... Factory setting: ALARM
• Sets the index code recording method (VISS signal).
When "ALARM" is set, an index code is recorded
whenever an alarm signal is received. To record index
codes at fixed one-hour intervals, set to "SKIP". In this
case, no index code is recorded when an alarm signal
is received.
5
<TAPE END BUZZER> ... Factory setting: OFF
• Set to ON to sound the buzzer when the tape ends
during recording.
5
<TERMINAL SEL 1> ... Factory setting: SERIES
Set the rear panel's [SERIES/CLOCK] terminal as
required. (Refer to page 19.)
5
<TERMINAL SEL 2> ... Factory setting: WARN
Select the signal output from the rear panel's
[WARNING/REC OUT] terminal. (Refer to page 19.)
24
[MENU] button
HIGH DENSITY
REC
CHECK
VIDEO CASSETTE RECORDER
PAUSE/
STILL
PLAY
SHIFT/TRACKING
MENU
FIELD
FF
TIME
SET/V.LOCK
ADVANCE
MODE
24H
[TIME MODE] button
SR-L911US
SHUTTLE
FIELD
FIELD
ADVANCE
REV
FWD
SHUTTLE
/FIELD
COUNT/
AL/PL
CLOCK
RESET
OPE. LOCK
OPERATE
RESET
TIMER
/CANCEL
REC
ON
SKIP/ALARM
SEARCH
5
<REC REMAIN> ... Factory setting: OFF
Select the timing to send the tape end information.
Choose from tape end (OFF), about 3 minutes before
the tape end (180S) or about 6 minutes before the tape
end (360S) during 8H mode.
When the tape reaches the selected position during
recording, the following information is output.
• Tape end signal from the rear panel's [TAPE END
OUT] terminal
• Series recording signal during series recording
• Tape end buzzer
• "End" indication in the counter display
5
<CAMERA SW> ... Factory setting: OFF
Sets the switching timing for cameras connected to an
external sequential switcher. (Refer to page 19.)
5
<ALARM REC> ... Factory setting: OFF
• Set to ON to perform alarm recording.
For details, refer to "Alarm Recording" on page 31.
5
<SENSOR REC> ... Factory setting: OFF
• Set to ON to perform sensor recording.
For details, refer to "Sensor Recording" on page 33.
5
<DURATION> ... Factory setting: 180 sec.
Selects the recording duration for alarm recording or
sensor recording. (Refer to page 20.)
5
<TAPE END MODE> ... Factory setting: STOP
Sets the operation mode at tape end when alarm or
sensor recording is executed. (Refer to page 20.)
Setting on the front panel
• Select the recording time mode with the [TIME MODE]
button. For details, refer to "Selection of the Record/
Play mode" on page 23.
Advertisement
Table of Contents
