Remote Switchboard Replacement; Remote Control Receiver Replacement; Led Driver Board Replacement - Dimplex BLF34 Service Manual

3. Using needle nose pliers, pinch the tabs on either side
of the switch to release and push the switch up and out
of the opening.
!
NOTE: Note the orientation of the switch prior to remov-
ing.
4. Locate the On/Off Switch (Figure 10).
5. Disconnect the wiring connections noting their original
locations.
!
NOTE: Using a flat head screwdriver gently pry between
the end of the connectors and the switch to release the
wires.
6. Reconnect wires onto the prongs on the switch in their
original configuration.
7. Insert the new switch by pushing switch back through
the hole past the side tabs on the switch, securing it in
the opening.
8. Reassemble in the reverse order as above.
REMOTE SWITCHBOARD
REPLACEMENT
WARNING: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required: Phillips head screwdriver.
Needle nosed pliers
Wire snips
CAUTION: Follow "Preparation for Service" instructions
before proceeding.
1. Remove the 2 screws, that secure the controls assem-
bly (Figure 9), located at the top of the mirror on the
right side of the unit.
2. Slide the controls assembly out toward the front of the
unit.
CAUTION: Ensure that the assembly is removed care-
fully, ensuring that no wires are caught or over strained.
3. Locate the switchboard (Figure 10).
4. Disconnect the wiring harness from the switchboard.
5. To remove the switchboard off of the plastic mounting
tabs, pinch the plastic mounting tabs with needle nose
pliers. Pull the old board off.
!
NOTE: If the location of the unit does not allow for the
tabs to be easily manipulated, the top portion of the mount-
ing tabs can be cut off (replacement ones are provided with
the replacement switchboard).
6. Line up the holes on the switchboard and gently press
the new board onto the mounts. Make sure the board
is secure.
7. Reconnect the wire harness onto the back of the
switchboard in its original configuration. .
8. Reassemble in the reverse order as above.
10
REMOTE CONTROL RECEIVER
REPLACEMENT
WARNING: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required: Phillips head screwdriver.
Needle nosed pliers.
Wire snips
CAUTION: Follow "Preparation for Service" instructions
before proceeding.
1. Remove the 2 screws, that secure the controls assem-
bly (Figure 9), located at the top of the mirror on the
right side of the unit.
2. Slide the controls assembly out toward the front of the
unit.
CAUTION: Ensure that the assembly is removed care-
fully, ensuring that no wires are caught or over strained.
3. Locate the remote control receiver (Figure 10).
4. Transfer the wiring connections from the existing re-
ceiver to the new receiver.
!
NOTE: Using a flat head screwdriver gently pry between
the end of the connectors and the board to release the
wires.
5. Remove the remote control receiver off the plastic
mounts by pinching the plastic mounting tabs with
needle nose pliers. Pull the old board off.
6. Line up the holes on the receiver and gently press the
new board onto the mounts. Make sure the board is
secure.
7. Reassemble in the reverse order as above.
CAUTION: When re-installing, be sure the wires are
guided and tucked into the proper openings along the right
side so they are not pinched and allows enough space to
reinstall the panel.

LED DRIVER BOARD REPLACEMENT

WARNING: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
CAUTION: If unit was operating prior to servicing allow
at least 10 minutes for lights and heating elements to cool
off to avoid accidental burning of skin.
Tools required: Phillips head screwdriver
Needle nosed pliers
Wire snips
CAUTION: Follow "Preparation for Service" instructions
before proceeding.
1. Remove the 2 screws, that secure the controls assem-
bly (Figure 9), located at the top of the mirror on the
right side of the unit.
2. Slide the controls assembly out toward the front of the
www.dimplex.com