JVC EXAD KW-AVX826 Instructions Manual page 70

INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding installation
kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used,
parts could become loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
1
Remove the audio system originally installed in the car, together with its mounting brackets.
Note: Be sure to keep all the screws and parts removed from your car for future use.
2
Attach the mounting brackets (removed from the car) to this unit (see below).
3
Do the required electrical connections.
• See pages 3 and 4.
4
Install this unit using the screws removed in step
5
Attach the monitor panel (see below).
The following example is for installation in a Toyota car. For more details, consult your JVC car audio
dealer.
Mounting bracket removed from the car
從汽車拆卸的裝配架
Supplied screws
配備螺絲
Select the appropriate type fitting to your
audio system space.
選擇適合您的音響系統安裝空間的型
號。
Note :
When installing the unit on the mounting bracket, make sure to use the supplied screws
(M5 x 8 mm). If longer screws are used, they could damage the unit.
注意: 安裝本機進裝配架時，請務必使用配備的螺絲 (M5 x 8 mm)。若使用比較長的螺絲，
有關螺絲可能會損壞本機。
Required space for installation and the monitor ejection
安裝和顯示器退出所需的空間
20
160
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the "–" terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car's chassis using shorter and thicker cords?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the "–" terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
1
.
Mounting bracket removed from the car
從汽車拆卸的裝配架
Dashboard
儀表盤
Unit: mm
單位: mm (毫米)
91.3
安裝 (裝設、固定在儀表板內)
下面的圖解表示了典型的安裝程序。但是在實際安裝時，您應該根據您的汽車作適當的調整。如果
您有問題，或需要有關配套元件的資料，請向 JVC 汽車音響分銷商或配套元件供應公司詢問。
• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。
安裝本機之前
• 當裝上本機時，必須按照指示使用配備的螺絲釘。如果使用其它的螺絲釘，相關零件可能會鬆
脫或損壞。
• 當鎖緊螺絲釘或螺栓時，切記不要壓擠到任何連接電線。
• 當安裝上後，切記不要阻擋到後面板的風扇以維持適當的通風。
1
拆卸原本安裝在汽車內的音響系統，以及其裝配架。
注意: 請務必保留所有從您汽車拆卸的螺絲和零件做日後使用。
2
將 (從汽車拆卸的) 裝配架安上本機 (參閱下圖)。
3
執行必要的電路連接。
• 參閱第 3 和 4 頁。
4 1
使用在步驟 拆卸的螺絲安裝本機。
5
安裝顯示器面板 (參閱下列內容)。
以下以豐田 (Toyota) 汽車安裝為例。請聯絡您的 JVC 汽車音響分銷商有關更多細節。
1
Screws removed from the car in step
在步驟 1 從汽車拆卸的螺絲
When installing the unit in a Nissan car
當安裝本機於日產汽車時
Install the unit at an angle of less than 30˚, taking it into
account that the monitor would eject when in use.
將本機安裝在少於 30˚ 的角度，您必須考慮到屏幕可
以在使用時退出。
故障排除
• 保險絲燒斷。
* 檢查紅色導線接頭和黑色導線接頭是否接觸正確？
• 電源不能接通。
* 檢查黃色導線接頭是否接上？
• 揚聲器沒有聲訊。
* 檢查揚聲器輸出導線接頭是否短路？
• 聲訊失真。
* 檢查揚聲器輸出端子是否接地？
* 檢查揚聲器的左 (L) ， 右 (R) 端子的負極"–"是否共同接地？
• 噪音干擾音響。
* 後接地端子與車身是否使用較短和較厚的電線連接？
• 本機發熱。
* 檢查揚聲器輸出端子是否接地？
* 檢查揚聲器的左 (L) ， 右 (R) 端子的負極"–"是否共同接地？
• 本機完全不能正確操作。
* 您有沒有重置本機？
2
Supplied screws
配備螺絲
If necessary, restore the protruding tabs.
若有必要，請重新裝上凸緣。
5 / 5
步驟
Step
Plate for use with a Nissan car
用於日產汽車的框
30˚
Monitor panel
顯示器面板