Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cardo Systems SCALA RIDER G4 POWERSET
Summary of Contents for Cardo Systems SCALA RIDER G4 POWERSET
-
Page 1: User Guide
PowerSet ™ User Guide... -
Page 2: Table Of Contents
G4 PowerSet headsets. Please visit www. 8. USING THE MOBILE PHONE ..........12 cardosystems.com/download/manuals to check if the manual you are now... -
Page 3: Introduction
➤Your headsets contain advanced software which you may update through your Windows® XP™ or Vista™ based PC. Your scala rider G4 PowerSet is a versatile communication and en- tertainment system with a wide range of connectivity options. Each ➤Your headsets offer spoken status instructions, so that you always... -
Page 4: Contents Of The Retail Box
2. CONTENTS OF THE RETAIL BOX 2 Wall charger plugs 2 USB adapter cables 2 Helmet clamps (subject to the version purchased: Boom-Mounted or Cord-Mounted Microphone) 2 Allen wrenches Two speakers 4 Velcro pads 2 MP3 cables MP3 Jack (back of clamp) 2 Glue plates Noise canceling... -
Page 5: Basic Setup And Configuration
4.2 SPOKEN STATUS ANNOUNCEMENTS Your wall charger and USB adaptor cable serve Your scala rider G4 headset offers various audio status messages two purposes: sent through your speakers. Among others, it will announce your con- 1. Charging your headset from any A/C nection state, e.g. -
Page 6: Firmware Upgrade Option
4.4 FIRMWARE UPGRADE OPTION Standard Method: Fastening the Clamp to the Helmet In the future you will be able to install firmware 1. Use the enclosed Allen Wrench to loosen upgrades and program patches to keep the software of your G4 up-to-date. Among others, the two screws on the Back Plate. -
Page 7: Attaching The Corded Microphone Clamp On Afull-Faced Helmet
3. Adjust the Helmet Clamp’s location on the Helmet so that the b. Attach the microphone to the Velcro, as shown in photo. microphone is located opposite the center of c. When done, tighten the screws of the clamp your mouth. You may need to reposition the 5.3 POSITIONING THE MICROPHONE AND SPEAKERS Clamp repeatedly until you identify the best spot. -
Page 8: Attaching And Removing The Headset From The Helmet Clamp
5.4 ATTACHING AND REMOVING THE HEADSET FROM THE 6. CONNECTING BLUETOOTH ENABLED MOBILE HELMET CLAMP PHONES, GPS OR MP3 (A2DP) DEVICES ATTACHING: Multiple Device Connectivity (“MDC”) with Bluetooth Slide the headset sideways (i.e. horizontally) compatible Devices along the sliding panel until a clicking sound indicates that the headset is locked in place. -
Page 9: Mobile Phone
6.1 MOBILE PHONE 6.2 GPS DEVICE To use your mobile phone with the scala rider G4, you must To use a Bluetooth enabled GPS device with the scala first pair your headset to the mobile phone. rider G4, the two must first be paired. This will allow Pairing is a one time process. -
Page 10: Mp3 Music (Wireless Option - A2Dp)
2. With the scala rider G4 headset turned ON, press and hold the NOTE: The priority schedule of your headset has been set in a way to avoid Mobile Button for at least six seconds until the Red and Blue Lights incoming intercom calls to interrupt GPS instructions in progress. -
Page 11: The Sound Of Music: Built-In Fm Radio And External Mp3 Player
7. THE SOUND OF MUSIC: BUILT-IN FM RADIO RDS ON/OFF (press simultaneously 3 seconds while rado is on) AND EXTERNAL MP3 PLAYER (CABLE OPTION) 7.1 FM RADIO The scala rider G4 is equipped with a FM stereo radio receiver and RDS (Radio Data System) technology, allowing you to choose how and when you listen to your favorite stations. -
Page 12: Cable Connecting Your Mp3 Player Or Other External Audio Sources
2. Search for a new station as described in the section above. NOTE: While listening to your MP3 player, the VOX feature is disabled 3. Tap the CHANNEL “B” button within 20 seconds of finding the sta- tion to save the current station. 8. -
Page 13: Using The Intercom
9.3 BEFORE STARTING THE INTERCOM The scala rider G4 PowerSet package contains two factory paired G4 headsets. To set up additional Intercom Bluetooth connections, Your scala rider G4 headset has two buttons designated for quick you must first pair your G4 headset with the other headsets. -
Page 14: Initiate Intercom Calls
GO TO HEADSETS TO BE PAIRED SECTION Your G4 with a third G4 unit 9.10 b Your G4 with one G4 and one Q2 unit 9.11 c Your G4 with two Q2 units 9.11 c Your G4 with one G4 and one other scala rider model 9.11 c Your G4 with one Q2 and one other scala rider model 9.11 c... -
Page 15: Enable/Disable Voice Connect Feature (Vox)
b. Busy Status (When using a G4 headset) NOTE: The headsets’ priority modes have been set to avoid incoming inter- When attempting an Intercom call with a headset that is already on com calls from interrupting mobile phone calls and GPS instruc- tions in progress. -
Page 16: Three-Way Intercom
1. While both G4 headsets are turned OFF, turn them ON by pressing and holding their Mobile Button until their Blue Lights flash three times. 2. Make sure that both headsets are now flashing slowly in Blue. NOTE: Selecting a CHANNEL that is already in use will override the paired First G4 unit Third G4 Headset headset on that CHANNEL with the newly paired headset. -
Page 17: Four-Way Intercom
a. Turn on the designated Rider “B” unit and the Rider “C” unit by entire group. Therefore, if one of the Passengers disconnects, the 4-way pressing their Mobile Buttons until their blue light flash three times. conference mode will be interrupted until that passenger is reconnected. b. -
Page 18: Using The G4 For Intercom With Other Scala Rider Headsets
NOTE: The scala rider G4 PowerSet package, contains two factory paired G4 headsets. If you did not change the original pairing settings, you can skip “step one” below: Step One: Pair Driver 1 to Passenger 2 via Channel “A” as follows a. -
Page 19: Two-Way Intercom With Scala Rider Q2
9.11a. TWO-WAY INTERCOM with scala rider Q2 2. Turn the other scala rider headset ON by pressing and holding its CTRL Button until the Red/Blue lights begin rapidly alternating. To use your scala rider G4 with a scala rider Q2 headset, we recom- 3. -
Page 20: 1C. Three Way Intercom (With Other Scala Rider Headsets)
(such as a Q2, Solo, FM, or TeamSet [Driver] headset) intercom call NOTE: The scala rider G4 PowerSet package, contains two factory paired G4 9.11c. THREE WAY INTERCOM (with other scala rider headsets) headsets. I f you did not change the original pairing settings, you Both scala rider G4 headsets included in your retail box are factory can skip step one below. -
Page 21: Support
• Connect the equipment into an outlet on a circuit different from that to 10. SUPPORT which the receiver is connected. For additional information please visit our website at • Consult the dealer or an experienced radio/TV technician for help. www.cardosystems.com Operation is subject to the following two conditions: FAQ: www.cardosystems.com/faq... -
Page 22: Waiver And General Release
1) this device may not cause interference and (jointly referred to as “Vehicle”) requires your complete and undivided attention. Cardo Systems, Inc., including its Officers, Directors, Affiliates, Parent Company, 2) this device must accept any interference, including interference that may Representatives, Agents, Contractors, Sponsors, Employees, Suppliers and Re- cause undesired operation of the device. - Page 23 Disclaimer of Warranty 1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and forever release, discharge, indemnify and hold harmless Cardo from any CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD and all litigation, claims, debts, demands, actions and liability which may arise, TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED directly or indirectly, from using the Device for any distress, pain, suffering, dis- WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,...
Need help?
Do you have a question about the SCALA RIDER G4 POWERSET and is the answer not in the manual?
Questions and answers