Hand-Held Ir Remote Control; Programming The Ir Remote Control; Sending Codes To The B100 Via The Ir Remote Control; Wired Rs232 Remote Control - Bryston B100 Owner's Manual

• W hile pointing the remote control at the B100, press the CODE button, followed by the three digit code
"247" using the keys numbered 1 through 0 in the illustration at the left. On your remote control these
keys, or buttons, are labeled AUX/PH (2), TUNER (4), D1 (7).
• T he three digit code should be entered within a few seconds of pressing CODE button or the unit will auto-
matically return to normal operation.
• T o clear the T2 trigger output, press the CODE button followed by the 3 digit code "248": AUX/PH (2), TUNER
(4), D2 (8).
A full function hand-held infra-red remote control is available for the B100 integrated amplifier
as an extra-cost option. The hand held remote unit is powered by two "AAA" batteries. To
change the battery remove the bottom cover plate by removing the four Philips screws on the
rear of the remote unit. Ensure that the batteries are correctly oriented and properly seated
in the battery holder.
The BR2remote is a full function remote allowing selection of all sources, volume up or
down (the volume control is a motor-driven design), mute ,left/right balance, power on/off
and discrete code entry.

SENDING CODES TO THE B100 VIA THE IR REMOTE CONTROL

Press the CODE button on the remote control (the red LED will light) and then enter the 3 digt code, as listed in the
"Wired RS232 Remote Control" section" below . The LED will flash to confirm transmission and then extinguish.

WIRED RS232 REMOTE CONTROL

Using the DB9-female connector at the rear of the unit, the B100 can receive commands via a null modem cable at
9600 baud, 8 data bits, no parity and 1 stop bit (9600,8,N,1). Valid commands will return the ">" character indicating
that the unit is ready to receive a new command. An invalid command will return the "!" character. These serial data
commands are as follows:
000 - power off
001 - select analog source 1 (A/D)
002 - select analog source 2 (AUX/PH)
003 - select analog source 3 (CD)
004 - select analog source 4 (TUNER)
005 - select analog source 5 (TV)
006 - select analog source 6 (VIDEO)
007 - volume up
008 - volume down
HAND-HELD INFRA-RED REMOTE CONTROL
We recommend maintaining a direct line-of-sight between the hand held remote unit and the
front of the B100 to ensure the most efficient operation of the remote features.
PROGRAMMING THE HANDHELD REMOTE CONTROL
The automatic motion-sensing backlight function in the handheld infra-red remote control unit
can be disabled by entering the 3 digit code "792" as follows:
1) Press and hold the CODE button for 5 seconds. Release when the LED flashes red.
2) A fter the LED stops flashing, enter the 3 digit code "792" by pressing the buttons D1, D3
then AUX/PH (see illustration on page 3)
3) To re-enable the motion-sensing backlight function, repeat steps 1 and 2 above
To completely disable the backlight, enter the 3 digit code "797" as follows:
1) Press and hold the CODE button for 5 seconds. Release when the LED flashes red.
2) A fter the LED stops flashing, enter the 3 digit code "797" by pressing the buttons D1, D3
then D1 (see illustration on page 3)
3) To re-enable the backlight repeat steps 1 and 2 above
015 - power on/off toggle
019 - balance left
020 - balance right
029 - power on
058 - mute on
059 - mute off
061 - record monitor toggle 248 - Clear Trigger 2 for current source
062 - record monitor on
063 - record monitor off
B100
INTEGRATED AMPLIFIER
081 - select digital source 1 (D1)
082 - select digital source 2 (D2)
083 - select digital source 3 (D3)
084 - select digital source 4 (D4)
245 - set/reset Pass Through mode
247 - Set Trigger 2 for current source
255 - System reset; restore defaults