Table of Contents
Advertisement
3. Connecting ATX Power Connector
The ATX power supply uses a 20-pin connector shown below. Make sure you plug in the
right direction.
4. Connecting Front Panel Cable
Attach the power LED, speaker, and reset switch connectors to the corresponding pins. If
you enable "Suspend Mode" item in BIOS Setup, the ACPI & Power LED will keep flashing
while the system is in suspend mode.
Locate the power switch cable from your ATX housing. It is 2-pin female connector from the
housing front panel. Plug this connector to the soft-power switch connector marked SPWR.
1
SPWR
ACPI & PWR
IDE LED
LED
ACPI LED
(Blue)
1
Speaker
Reset
NC
NC
+5V
IDE LED
IDE LED
+5V
+5V
GND
NC
SPEAKER
SPWR
GND
ACPI LED-
GND
ACPILED
NC
ACPI_B
GND
RESET
GND
5. Setting CPU Voltage & Frequency
Full-range Adjustable CPU Core Voltage
This motherboard supports CPU VID function. The CPU core voltage will be automatically
detected and the range is from 1.1V to 1.85V. It is not necessary to set CPU Core Voltage.
Setting CPU Frequency
This motherboard is CPU jumper-less design, you can set CPU frequency through the
BIOS setup, and no jumpers or switches are needed.
BIOS Setup > Frequency / Voltage Control > CPU Speed Setup
Core Frequency = CPU FSB Clock * CPU Ratio
CPU Ratio
From 5.5x to 16x step 0.5x
CPU FSB (Adjustment
FSB = 100MHz-200MHz by 1MHz Stepping
manually)
CPU Overclocking
CPU
CPU Core Frequency
Athlon 1G
1GHz
Athlon 1.13G
1.13GHz
Athlon 1.2G
1.2GHz
Athlon 1.33G
1.33GHz
Athlon 1.4G
1.4GHz
AthlonXP 1500+
1.3GHz
AthlonXP 1600+
1.4GHz
AthlonXP 1700+
1.46GHz
AthlonXP 1800+
1.53GHz
AthlonXP 1900+
1.6GHz
AthlonXP 2000+
1.667GHz
AthlonXP 2100+
1.73GHz
AthlonXP 2200+
1.80GHz
AthlonXP 2400+
2.0GHz
AthlonXP 2600+
2.13GHz
AthlonXP 2700+
2.16GHz
AthlonXP 2800+
2.25GHz
Duron 1G
1GHz
Duron 1.1G
1.1GHz
Duron 1.2G
1.2GHz
Duron 1.3G
1.3GHz
Note:
With CPU speed changing rapidly, there might be fastest CPU on the
market by the time you received this installation guide. This table is kindly for
your references only.
Note: Due to the limitation of nVidia chipset itself, if the FSB overclocking frequency is
extremely high, (for example, over 160MHz), the Watch Dog ABS and Home key
function may not be able to automatically recover your motherboard. In such case,
please clear CMOS by JP14.
Tip: If your system hangs or fails to boot because of overclocking, simply use
<Home> key to restore the default setting or you can wait the AOpen "Watch Dog
Timer" reset the system in five seconds and system will auto-detect hardware again.
Note: You have to
adjust CPU FSB in
BIOS after installing
EV6 Bus Clock
Ratio
CPU; otherwise CPU
266MHz
7.5x
will
run
266MHz
8.5x
266MHz
9.0x
speed of CPU FSB
266MHz
10.0x
266MHz
10.5x
value.
266MHz
10.0x
266MHz
10.5x
266MHz
11.0x
266MHz
11.5x
Warning: nForce2- GT
266MHz
12.0x
chipsets
266MHz
12.5x
266MHz
13x
166MHz
266MHz
13.5x
266MHz
15x
performance
266MHz
16x
maximum
333MHz
13x
333MHz
13.5x
EV6 system bus) and
200MHz
10.0x
66MHz
200MHz
11.0x
200MHz
12.0 x
higher
clock
200MHz
13.0 x
may
cause
system damage.
at
default
support
FSB
(with
reaches
333MHz
AGP
clock,
setting
serious
Advertisement
Table of Contents
