Download Print this page

Makita 9047L Instruction Manual

180 mm (7")/230 mm (9")
Hide thumbs Also See for 9047L:

Advertisement

Quick Links

Angle Grinder
6,000
180 mm (7")
MODEL 9047L
230 mm (9")
MODEL 9049
470 mm
(18-112")
4.8
kg
(10.6 lbsl
518"- 11
UNC
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPEC IF I CAT1
0
N
S
1
Overall length
1
Net weight
1
Spindle thread
N o
load speed
(RPM)

Advertisement

loading

Related Manuals for Makita 9047L

Summary of Contents for Makita 9047L

  • Page 1 Angle Grinder 180 mm (7") MODEL 9047L 230 mm (9") MODEL 9049 INSTRUCTION MANUAL DOUBLE INSULATION SPEC IF I CAT1 load speed Overall length Net weight Spindle thread (RPM) 470 mm (18-112") (10.6 lbsl 518"- 11 6,000...
  • Page 2: General Safety Rules

    GENERAL SAFETY RULES Tools) (For All WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. 1. Keep your work area clean and well Cluttered benches and dark areas invite lit.
  • Page 3 Avoid accidental starting. Be sure switch is off before plugging Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
  • Page 4: Specific Safety Rules

    Specific Safety Rules Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. Accessories must be rated for at last the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury.
  • Page 5 The followings show the symbols used for tool........volts ......... amperes ......... hens ......... kilograms ......... hours ......... minutes ......... seconds ......... alternating current ......... direct current ......... no load speed ......... alternating or direct current ......... Class Construction .........
  • Page 6 Installing wheel guard When using a depressed center wheel or an abrasive cut-off wheel, always use a wheel guard. Mount the wheel guard with the tab ,-Wheel guard on the wheel guard band aligned w i t h the notch on the bearing box Then rotate the wheel guard 160 degrees counterclockwise.
  • Page 7 Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw Lock nut the lock nut onto the spindle.
  • Page 8 Operation Hold the tool firmly. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15O to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece.
  • Page 9 Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjust- ment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
  • Page 10 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified this manual. The use any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
  • Page 11 Size For Model 743206-A 1 5 0 (6") 741445-0 743206-8 741441-8 17" x 118' x 718"l 741442-6 9047L (includes one back pad, 741443-4 Part No. 743027.41 @Urethane washer 14 Part No. 2 6 1 0 3 9 - 0 741444-2 @Plastic pad Part No.
  • Page 12: Angle Grinder

    No".-01 -'96 US ANGLE GRINDER 180 mm (7") Model 9047L (9") Model 9049 Note: The switch and other part configurations may differ from country to country.
  • Page 13 Nov.-D1--'96 MODEL 9047L. 9 0 4 9 'Ft &. & , DESCRIPTION DESCRIPTION MACHINE FIELD ASSEMBLY Retaining Ring R-40 Ball 6203DDW Baffle Plate Bearmg Bearing B O X Ball Bearing 6200DDW Insulation Washer Spindle Pan Head Screw Max25 ARMATURE ASSEMBLY...
  • Page 14 Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, t o one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.

This manual is also suitable for:

9067l90699049