Related Manuals for Husqvarna 225AI15
Summary of Contents for Husqvarna 225AI15
- Page 1 225AI15/AI25 Operator's Manual Read through the Operator‘s Manual carefully and understand the content before using the machine. 101 91 39-26...
-
Page 2: Symbol Explanation
SYMBOL EXPLANATION Symbols Checks and/or maintenance should be carried out with the engine switched off, with the stop switch in the STOP position. WARNING! This machine can be dangerous! Careless or incorrect use can result in serious, even fatal injury. Always use approved protective gloves. -
Page 3: Table Of Contents
CONTENTS List of contents Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. SYMBOL EXPLANATION Symbols ................2 CONTENTS WARNING! List of contents ..............3... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS Personal protective eqipment The machine’s protective equipment This section describes the machine‘s safety equipment, its IMPORTANT INFORMATION function and how checks and maintenance are carried out to • Incorrect or careless use of this machine can turn ensure that it operates correctly. (See the chapter “What is it into a dangerous tool that can cause serious or what“... -
Page 5: Control, Maintenance And Service Of The Machine's Safety Equipment
SAFETY INSTRUCTIONS 3. Muffler Control, maintenance and service of the machine‘s safety equipment The muffler is designed to give the lowest possible IMPORTANT INFORMATION noise level and to direct the engine’s exhaust fumes away • All service and repairs to the machine require from the user. - Page 6 SAFETY INSTRUCTIONS 1. Throttle trigger lock 3. Muffler • Check that the throttle is • Never use a machine that locked in the “idling has a defective muffler. position“ when the throttle trigger lock is in • Check regularly that the its original position.
-
Page 7: General Safety Instructions
SAFETY INSTRUCTIONS General safety instructions Fuel safety • Never fill the machine while the engine is running. Always IMPORTANT INFORMATION stop the engine and let it cool for a few minutes before • The machine is solely designed for drilling in refuelling. -
Page 8: Safety Instructions For Using The Machine
SAFETY INSTRUCTIONS Safety instructions for using the Protective instructions while working machine. • Always ensure you have a safe and firm working WARNING! position. The machine can cause serious personal injury. Read the safety instructions carefully. Learn how to use the machine. •... -
Page 9: Fitting The Auger
SAFETY INSTRUCTIONS Protective instructions when Fitting the auger work is completed • Fit the auger (A) to the • The transport guard must always be fitted to the cutting output shaft (B). attachment when the machine is not in use. •... -
Page 10: What Is What
WHAT IS WHAT? What is what on the ice drill? 1. Operator’s Manual 12. Choke 13. Allen key 2. Gearbox 14. Spark plug spanner 3. Loop handle 4. Cylinder cover 15. Blade cover (Transport) 5. Starter handle 16. Air purge 17. -
Page 11: Fuel Handling
Lit. 0,10 0,15 Mixing ratio 1:50 (2%). 0,20 0,30 • If HUSQVARNA two-stroke oil is not available you can 0,45 0,30 use a high quality two-stroke oil intended for air cooled 0,60 0,40 engines. Contact your dealer when selecting an oil. -
Page 12: Start And Stop
START AND STOP Control before starting Warm engine IGNITION: • Check the cutters. Never Set the stop switch to the use cutters that are blunt, start position. cracked or damaged. CHOKE: Set the choke control in the • Check that the machine choke position and then is in full working order. -
Page 13: Maintenance
Basic setting • The carburettor is set to its basic setting when test run at Your Husqvarna product has been designed and manufac- the factory. The basic setting is richer than the optimal tured to specifications that reduce harmful emissions. -
Page 14: Muffler
MAINTENANCE Cooling system Muffler NOTE! To maintain as low operat- Some mufflers are fitted with catalytic converters. See “Techni- ing temperature as possible cal data” to find out if your machine is equipped with a the engine is equipped with catalytic converter. -
Page 15: Air Filter
MAINTENANCE Air filter Maintenance schedule The air filter (A) should be Below follows some general maintenance instructions. cleaned regularly removing If you need further information please contact your service dust and dirt to avoid: workshop. • carburettor malfunction • starting problems Daily maintenance •... -
Page 16: Weekly Maintenance
MAINTENANCE Weekly maintenance Monthly maintenance 1. Check the starter, the starter cord and the 1. Clean the fuel tank. return spring. 2. Clean the carburettor and 2. Clean the outside of the the area surrounding it. spark plug. Remove and check the electrode gap. -
Page 17: Technical Data
TECHNICAL DATA Technical data 225AI15 225AI25 Engine Cylinder capacity, cu. inch/cm 1,64/26,9 1,64/26,9 Cylinder bore, inch/mm 1,38/35 1,38/35 Stroke length, inch/mm 1,10/28 1,10/28 Idling speed, rpm 2 700 2 700 Recommended max. speed, rpm 11 200-12 000 11 200-12 000 Max. - Page 18 We, Husqvarna AB, S-561 82 Huskvarna, Sweden, tel: +46 36-146500, declare under sole responsibility that the ice augers Husqvarna 225AI15 and 225AI25 from 1998’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the following standards or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:...
- Page 19 English –...
- Page 20 ´*3-|¶6[¨ 2000W43...