Husqvarna 225AI15/AI25 Operator's Manual

Husqvarna 225AI15/AI25 Operator's Manual

Husqvarna drill operator's manual

Advertisement

225AI15/AI25
Operator's Manual
Read through the Operator's Manual carefully and
understand the content before using the machine.
(EPA)
101 91 39-95

Advertisement

Table of Contents
loading

Summary of Contents for Husqvarna 225AI15/AI25

  • Page 1 225AI15/AI25 Operator's Manual Read through the Operator‘s Manual carefully and understand the content before using the machine. (EPA) 101 91 39-95...
  • Page 2: Symbol Explanation

    SYMBOL EXPLANATION Symbols WARNING! This machine can be dangerous! Careless or incorrect use can result in serious, even fatal injury. Read through the Operator‘s Manual carefully and understand the content before using the machine. Always use • Ear protection • This product is in accordance with applicable CE directives.
  • Page 3: Table Of Contents

    Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual.
  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective eqipment IMPORTANT INFORMATION • Incorrect or careless use of this machine can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand this manual. •...
  • Page 5: Control, Maintenance And Service Of The Machine's

    SAFETY INSTRUCTIONS 3. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine’s exhaust fumes away from the user. A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust emissions.
  • Page 6 1. Throttle trigger lock • Check that the throttle is locked in the “idling position“ when the throttle trigger lock is in its original position. • Press in the throttle trigger lock and make sure it returns to its original position when released.
  • Page 7: General Safety Instructions

    SAFETY INSTRUCTIONS General safety instructions IMPORTANT INFORMATION • The machine is solely designed for drilling in ice. • Never use the machine if you are tired, if you have consumed alcohol, or if you are taking medicines that can affect your sight, your judgement or the control of your body.
  • Page 8: Safety Instructions For Using The Machine

    Safety instructions for using the machine. WARNING! The machine can cause serious personal injury. Read the safety instructions carefully. Learn how to use the machine. WARNING! Cutting tool. Do not touch the cutting attachment without first switching off the engine NOTE! Read the safety instructions carefully before starting to use the machine.
  • Page 9: Fitting The Auger

    • Make sure you have a safe and steady working position. • Always use both hands to hold the machine. • Place the tip of the drill on the ice. • Open the throttle gradually when the drill begins to bite into the ice.
  • Page 10: What Is What

    What is what on the ice drill? 1. Operator’s Manual 2. Gearbox 3. Loop handle 4. Cylinder cover 5. Starter handle 6. Stop switch 7. Throttle trigger lock 8. Throttle trigger 9. Fuel tank 10. Fuel cap 11. Air filter cover –...
  • Page 11: Fuel Handling

    Two-stroke oil • For the best results use HUSQVARNA two-stroke oil, which has been specially developed for HUSQVARNA’s small, two-stroke engines. Mixing ratio 1:50 (2%). • Never use two-stroke oil intended for water cooled outboard motors, so-called outboard motor oil.
  • Page 12: Start And Stop

    Control before starting • Check the cutters. Never use cutters that are blunt, cracked or damaged. • Check that the machine is in full working order. Check that all nuts and bolts are tightened correctly. • Check that the cutting attachment always stops when the engine is idling.
  • Page 13: Maintenance

    Carburettor Your Husqvarna product has been designed and manufac- tured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak perform-...
  • Page 14: Muffler

    Muffler NOTE! Some mufflers are fitted with catalytic converters. See “Techni- cal data” to find out if your machine is equipped with a catalytic converter. The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user.
  • Page 15: Air Filter

    Air filter The air filter (A) should be cleaned regularly removing dust and dirt to avoid: • carburettor malfunction • starting problems • reduced engine power • unnecessary wear to engine parts • abnormal fuel consump- tion Clean the filter after every 25 hours or more regularly if operating conditions are exceptionally dusty.
  • Page 16: Weekly Maintenance

    Weekly maintenance 1. Check the starter, the starter cord and the return spring. 2. Clean the outside of the spark plug. Remove and check the electrode gap. Adjust the gap to 0.5 mm or change the spark plug. 3. Clean the cooling fins on the flywheel.
  • Page 17: Technical Data

    EN 11806 and ISO 10884, dB(A): Vibration levels Vibration levels on the handles measured according to EN 11806 and ISO 7916, Idling, left/right handle: Max. speed, left/right handle: Approved cutting attachment Drill Drill Drill Drill Extension (Rallonge) TECHNICAL DATA 225AI15...
  • Page 18: Emission Control Warranty Statement

    REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be perfor- med at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest &...
  • Page 19 English –...
  • Page 20 ´*3-•¶5q¨ 2000W43...

This manual is also suitable for:

225ai15225ai25

Table of Contents