Table of Contents
Advertisement
Power supply voltage:
220 – 240 V, 50/60 Hz
(Power supply control range 165 ... 265 V)
»The appliance may be operated only using the
mains cable set supplied. It prevents mains inter-
ference and is an integral part of the device
approval«.
For replacement purposes please order from an
approved service specialist only the mains cable
set
with
the
description
8290.991-220«.
Power consumption during recording:
approx. 60 W, 9 W in standby
Reception area:
Channels C01 ... C99, special channels S01 ... S41
Additional components:
The set has been prepared for retrofitting with a
communications card for hotel/hospital use. Con-
sult your authorised dealer.
Final sound stage:
8 W music signal power (4 W sinus)
Contact assignment for the Euro-AV socket
If you intend to connect auxiliary appliances to the
TV set (e. g. computer, amplifier system), then your
service specialist will be able to make a connection
compatible with official standards by following the
connection table below:
Pin
Signal
11
= Audio output right
12
= Audio input right
13
= Audio output left
14
= Audio ground
15
= Blue ground
16
= Audio input left
17
= RGB blue input
18
= Switching voltage
19
= Green ground
10
= Data cable
11
= RGB green input
12
= –
13
= Red ground
14
= Ground
15
= RGB red input (chroma; S-Video)
16
= RGB switching voltage
17
= Video ground
18
= RGB switching voltage ground
19
= Video output
20
= Video input
21
= Shielding/ground
20
2
21
19
1
Subject to alteration and correction!
»part
number
Service notes for authorised dealers:
The product fulfills the requirements of
the following EU guidelines:
73/23/EEC guideline on electrical equipment for use
with certain voltage limits. 89/336/EEC guideline on
electromagnetic compatibility.
The set complies with the standards:
EN 60065, EN 55013, EN 55020
The appliance conforms to VDE safety regulations
and Deutsche Bundespost regulations (approval
mark, see type-ID sticker on back of set), further-
more to the regulation on protection from harm by
X-rays. The x-ray emission – caused by the tube – is
sufficiently shielded and is therefore completely safe.
Accelerating voltage 25 kV/mean electron flow 1.0 mA.
Tampering, in particular adjusting the high voltage
or installation of a different tube type can lead to the
x-ray emission substantially increasing. Sets which
have been modified in such a way no longer corre-
spond with this approval and may not be operated.
GRUNDIG customer service centre
If you have any questions on the environ-
mental impact of our TV sets, please contact
GRUNDIG Öko-Technologie,
Fax: 0911/703-9213.
Additional Information for Units sold in Great Britain
Units sold in GB are suitable for operation from a 240 V
AC, 50 Hz mains supply.
In case this appliance is supplied with a Safety Standard
Approved mains lead fitted with a non-rewireable 13 Amp
mains plug which, if unsuitable for your socket, should be
cut off and an appropriate plug fitted by a qualified electri-
cian. The fuse and fuse holder must be removed from the
plug as accidental insertion of the redundant plug into a 13
Amp socket is likely to cause an electrical hazard.
Note: The severed plug must be destroyed to avoid a pos-
sible shock hazard should it be inserted into a 13
Amp socket elsewhere.
If it is necessary to change the fuse in the non-rewireable
plug, the correct type and rating (5 Amp ASTA or BSI
approved BS 1362) must be used and the fuse cover must
be refitted. If the fuse cover is lost or damaged the lead and
plug must not be used until a replacement is obtained.
Replacement fuse covers should be obtained from your
dealer.
If a non-rewireable plug or a rewireable 13 Amp (BS 1363)
plug is used, it must be fitted with a 5 Amp ASTA or BSI
approved BS 1362 fuse. If any othe type of plug is used it
must be protected by a 5 Amp fuse either in the plug or at
the distribution board.
Important:
The wires in the mains lead are coloured in accordance
with the following code:
BLUE
– NEUTRAL
BROWN
– LIVE
As the colours of the wires in the mains lead of your appli-
ance may not correspond with the coloured marking iden-
tifying the terminals in your plug, proceed as follows:
Connect the BLUE coloured wire to plug terminal marked
with the letter "N" or coloured black.
Connect the BROWN coloured wire to the plug terminal
marked with a letter "L" or coloured red.
In no circumstance must any of the wires be connected to
the terminal marked with a letter "E", earth symbol
coloured green or green and yellow.
Replacement mains lead can be obtained from your dealer.
,
17
Hide quick links:
Advertisement
Table of Contents
