Subscribe to Our Youtube Channel
Related Manuals for COEF MP 150 SPOT DV
Summary of Contents for COEF MP 150 SPOT DV
- Page 1 Code ZL-013001-01 OPERATING INSTRUCTIONS Revision 2.0...
-
Page 2: Table Of Contents
SUMMARY DECLARATION OF CE CONFORMITY................2 ADVICES FOR A CORRECT INSTALLATION..............2 GENERAL WARRANTY CONDITIONS ................3 PACKING CONTENTS ..................... 3 1.0 DIMENSIONS & POSITIONING................. 4 2.0 TECHNICAL NOTES ....................4 3.0 INSTALLATION ......................5 3.1 LAMP MOUNTING OR REPLACING ................5 3.2 PROJECTOR INSTALLATION .................. -
Page 3: Declaration Of Ce Conformity
Declaration of CE conformity We Manufacturer Room 2310-2311, Press Building, No 2 Shennan Zhong Road, Shenzhen, China, 518027 Declare that the product MP150 Spot DV is in conformity with 89/336 EEC-EMC directive and with the actual required safety standars in accordance with LVD 73/23 EEC Shenzhen, 01 October 2005 ATTENTION: carefully read the directions of this manual. -
Page 4: General Warranty Conditions
Please find here below a list of symbols and relative meaning. OPERATOR Not particulary qualified staff, that can operate when no specific knowledge is required COEF OPERATOR Technical staff, qualified and trained by the constructor, for repair and extraordinary operations. MECHANICAL OPERATORS Staff employed in the ordinary mechanical maintenance. -
Page 5: Dimensions & Positioning
1.0 DIMENSIONS & POSITIONING It is possible to set up the MP150 Spot DV in any position. 2.0 TECHNICAL NOTES Code: ZL-013001-01 MP150 Spot DV • Lamp: HSD 150/70 -12.000 lumen • 16 bit movement resolution -PAN 540° / TILT 270°with automatic repositioning •... -
Page 6: Installation
3.0 INSTALLATION The constructor is not be considered responsible in case of: • Improper use of the unit or use by not trained staff • Use in contrast with the directions on work safety • Wrong installation • Defective power supply •... -
Page 7: Projector Installation
After such an intervention the safetychain must be replaced with another original part. ATTENTION: COEF is not responsible for installations not correctly made or made without respecting the above indications: those installations are considered dangerous... -
Page 8: Power Supply Connection
Power : indicated in the the serigraphy table (tollerance: +5% / -10%) Should there be different electrical characteristics or special steps to be carried out, please contact COEF by telephone or e-mail. Supply the projector by connecting it as indicated in picture. -
Page 9: Special Functions And Projector Assignment
5.0 SPECIAL FUNCTIONS AND PROJECTOR ASSIGNMENT On the front panel of MP150 Spot DV you'll find a section for the additional functions and for setting the projector. Following the picture, you can see all the offered possibilities in detail. All operations are to be carried out with the A, B, C, D. -
Page 10: Menu, Function & Sub-Functions
6.0 MENU, FUNCTION & SUB-FUNCTIONS (* ) = default value -factory assigned (*)1/504 O (*) 1/505 DMX start channel SHOW KH,H Lamp working hours (KH = thousand H = hours) LAMP TIME Lamp working hours reset (confirm by ENTER) MACH SHOW KH,H E OK... -
Page 11: Channels And Digital Values
7.0 CHANNELS AND DIGITAL VALUES CHANNEL DMX VALUE FUNCTION SHUTTER-STROBO SHUTTER CLOSED FLASH RANDOM FAST 6-20 21-40 FLASH RANDOM MEDIUM 41-60 FLASH RANDOM SLOW STROBE SPEED ADJUSTMENT 61-250 SHUTTER OPEN 251-255 COLORS NEUTRAL YELLOW 6-15 BLUE 16-25 MAGENTA 26-35 GREEN LIGHT 36-45 ORANGE 46-55... -
Page 12: Special Action
CHANNEL 2 and CHANNEL3=value0>255>0 7.2 AUTONOMOUS OPERATION The Mp 150 Spot DV has a particularity that marks it from most of similar product: the possibility of an entirely autonomous operation, free from connection to any control unit. This feature allows the projector, or the projectors connected between them, to perform 4 different programs pre-planned selectable easily across the control panel of the projector (you see paragraph MENU -FUNCTIONS and SUB-FUNCTION section “SELF”). -
Page 13: Lamp Adjustment
8.0 LAMP ADJUSTMENT • Don’t look directly the beam trough the lens. • The lamp is pre-regulated by the factory. Only fine-adjustment. Don’t move the screws ”B” up to upper or lower extremities. Lamp adjustment is necessary to obtain a uniform and powerful light beam. Switch on the projector and set the channels without gobo and colors. - Page 14 After had access to the inside part of the projector ( unscrew the 5 Screw (A) to take out the cover of the base to enter the sensors of the PAN movement ) special caution will be dedicated to the sensors that put on a fundamental role in the operation of the equipment. The sensors are indispensable in the moment of the general reset of the projector, function that if not perform correctly, harms in total manner the normal operation of the projector, at least for what pertains the group associated to the sensor.
-
Page 15: Elettronic Maintenance
9.2 ELETTRONIC MAINTENANCE WARNING: switch off the projector before operating This section is dedicated in detail to the electronic connections between the card and the mechanical components, assembled in the projector.These information will be absolutely necessary when the mechanical unit has to be removed from the projector for maintenance and/or repair. -
Page 16: Troubleshooting
10.0 TROUBLESHOOTING - The power supply is not present - Check if the regular power supply is present on the projector. The projector doesn’t swich on - The lamp is not working - Replace the lamp. Just to wait for little of time. - The thermal switch is active Make sure that the projector is correctly - Wrong DMX configuration... - Page 18 ®...
Need help?
Do you have a question about the MP 150 SPOT DV and is the answer not in the manual?
Questions and answers