Related Manuals for COEF Sirio RAY 1200 02B014
Summary of Contents for COEF Sirio RAY 1200 02B014
-
Page 1: Operating Instructions
COEF srl. Via Albinatico, 80-82 51019 Ponte Buggianese (PT) ITALY www.coef.it / www.coef.net info@coef.it Code 02B014 - Sirio RAY 1200 • Code 02B015 - Sirio RAY 1800 • • OPERATING INSTRUCTIONS Revision 1... -
Page 2: Declaration Of Ce Conformity
2) The protection screens, the lenses, or the ultraviolet filters must be replaced if they are visibly damaged and their effective- ness has been reduced, for example, by cracks or deep scratches. 3) Do not look directly at the lamp while lamp is on. Declaration of CE conformity COEF srl. Via Albinatico, 80-82 / ITALY 51019 Ponte Buggianese (Pistoia) -
Page 3: General Warranty Conditions
•BEAM ANGLE: Continuously variable (256 steps), Spot: 5° - 8° •Flood: 11° - 14° •POWER INPUT: Rated voltage: 230Vac 50Hz; 230Vac 60Hz, On request: 208Vac 60Hz; 200Vac 50Hz Rated power: 2200 VA, Rated current: 10A (230Vac) http://www.coef.net - info@coef.it Pag. 3... -
Page 4: Before Using
The lamp must be replaced if it has been damaged or thermally deformed. Clean regularly the in-out ventilating grilles. Do not handle the spot by taking it by the head, but always by using the special handles. Pag. 4 http://www.coef.it info@coef.it... - Page 5 You must control that the two filters completely cover the overall of the air entrance. http://www.coef.net - info@coef.it Pag. 5...
-
Page 6: Control Panel
• DOWN to go backward in the selected options • UP to go forward in the selected options • ENTER to confirm the selected options DISPLAY Shows the various menus and the selected options. Pag. 6 http://www.coef.it info@coef.it... - Page 7 Down and UP. A control of the memory will be run and all the default settings will be stored: the display will then show Init. If the memory is damaged, the display will show the message FAIL. To go back to the op- tions without making any change, press the MENU button. http://www.coef.net - info@coef.it Pag. 7...
- Page 8 CH 2= Cyan CH 2= Cyan CH 3= Yellow CH 3= Yellow CH 4= Magenta CH 4= Magenta CH 5= Dimmer CH 5= Dimmer CH 6= Beam angle CH 6= Beam angle CH 7= Reset/Lamp Off Pag. 8 http://www.coef.it info@coef.it...
- Page 9 EXAMPLE 1: connection controller-spot with 1 DMX 512 output LAST SPOT SPOT SPOT SPOT CONTROLLER DMX TERMINATION RESISTOR EXAMPLE 2: connection controller-spot to one DMX 512 output over 150mts long LAST SPOT SIGNAL AMPLIFIER SPOT CONTROLLER DMX TERMINATION RESISTOR http://www.coef.net - info@coef.it Pag. 9...
- Page 10 EXAMPLE OF CONNECTION AND SETTING OF 4 “SIRIO RAY” IN SYNCHRO - MODE MASTER SLAVE SLAVE SLAVE WARNING: the cables are the same as the DMX standard cable EXAMPLE OF CONNECTION AND SETTING OF 4 “SIRIO RAY” IN INDIPENDENT AUTO - MODE MASTER MASTER MASTER MASTER Pag. 10 http://www.coef.it info@coef.it...
-
Page 11: Troubleshooting Guide
• Description of the problem and the troubleshooting procedures that you have performed so far to diagnose and resolve the fault. You can contact your authorized COEF dealer or directly COEF Technical Service. (fax. +39.0572.636535 - e-mail: technical@coef.it) Appendix “C” - Table A1 http://www.coef.net - info@coef.it... - Page 12 DATA LINK (DMX 512) TROUBLESHOOTING Appendix “C” - Table A2 Pag. 12 http://www.coef.it info@coef.it...
-
Page 13: Main Board Connections
Check the main fuse, if it is blown check VR1 (normally it has a resistance = ¥). If it is in short circuit you must change it. Check D1 (Bridge Rectifier), if it is ok check C65. If the fuse is still blown, change U11 http://www.coef.net - info@coef.it Pag. 13... - Page 14 THE COMPLETE LIST OF DMX VALUES APPENDIX -A- THE COMPLETE LIST OF THE AVAILABLE GAMES APPENDIX -B- Pag. 14 http://www.coef.it info@coef.it...
Need help?
Do you have a question about the Sirio RAY 1200 02B014 and is the answer not in the manual?
Questions and answers