Technical Data; Before Starting The Equipment; Assembling The Saw - EINHELL BT-SM 2050 Operating Instructions Manual

Anleitung_BT_SM_2050_SPK1:_
Contact with the saw blade in the uncovered saw
zone.
Reaching into the running saw blade (cut
injuries).
Kick-back of workpieces and parts of workpieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw
blade.
Damage to hearing if essential ear-muffs are not
worn.
Harmful emissions of wood dust when the
machine is used in closed rooms.

5. Technical data

Asynchronous motor
Output
Operating mode
Idle speed n
0
Carbide-tipped saw blade
Number of teeth
Tilting range
Mitre cuts
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45°
(double mitre cuts)
Weight
Noise emission values
The sawʼs noise is measured in accordance with
DIN EN ISO 3744; 11/95, E DIN EN 31201; 6/93,
ISO 7960 Annex A; 2/95. The machine may
exceed 85 dB(A) at the workplace. In this case,
noise protection measures need to be introduced
for the user (ear-muffs).
Sound pressure level L
pA
Sound power level L
WA
„The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immision level
at the workplace include the duration of impact, the
type of room, and other sources of noise etc., e.g.
the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
12.01.2009 15:45 Uhr
user should at least be able to make a better
assessment of the dangers and risks involved."

6. Before starting the equipment

6.1 General information
The equipment must be set up where it can stand
securely, i.e. it should be bolted to a workbench,
a universal base frame or similar.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
230 V~ 50 Hz
such as nails or screws etc.
1700 W
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
S1
machineʼs moving parts run smoothly.
4800 min -1
Before you connect the machine to the power
ø 210 x ø 30 x 2,8 mm
supply, make sure the data on the rating plate is
24 the same as that for your mains.
-45° / 0°/ +45°
6.2 Assembling the saw (Fig. 1-5)
0° to 45° to the left
To adjust the turntable (17), loosen the locking
205 x 65 mm
grip (14) by approx. 2 turns, which frees the
turntable (17).
140 x 65 mm
Press the locking lever (13), turn the turntable (17)
and scale pointer (15) to the desired angular
140 x 40 mm
setting on the dial (16) and lock into place with
the locking grip (14). The saw has locking
15 kg
positions at angular positions of -45°, -30°, -22,5°,
-15°, 0°, 15°, 22,5°, 30°, 45° at which the locking
lever can be engaged.
To release the saw from its position at the bottom,
pull the locking pin (25) out of the motor mounting
while pressing down lightly on the machine head
(4). Turn the locking pin (25) through 90° before
you release it so that the saw remains released.
Swing the machine head (4) up until the release
lever (3) latches into place.
Idle speed
The clamping device (8) can be fitted on either the
86 dB(A)
left or right of the fixed saw bench (18).
99 dB(A)
Undo the locking screws for the workpiece
support (30).
Mount the workpiece support (10) on the fixed
saw table (18) and tighten the appropriate locking
screw (26) (Figure 4).
Mount the second workpiece support (10) on the
opposite side of the saw and secure with the
appropriate locking screw (30).
When the locking screw (21) is loosened, you can
tilt the machine head (4) to the left by up to 45°.
Screw the additional stability bar (9) to the back
of the equipment.
Seite 15
GB
15