Replacing The Power Cable; Cleaning, Maintenance And Ordering Pf Spare Parts; Changing The Saw Blade; Limiting The Cutting Depth - EINHELL BT-SM 2050 Operating Instructions Manual

Anleitung_BT_SM_2050_SPK1:_
7.4 Miter cut 0°- 45° and turntable 0° - 45°
(Fig. 1 – 3, 14)
The crosscut saw can be used to make miter cuts of
0°- 45° to the left relative to the work surface and, at
the same time, 0° - 45° to the left or 0° - 45° to the
right of the stop rail (double miter cut).
Remove the clamping device (8) if necessary or fit
it on the opposite side of the fixed saw bench
(18).
Move the machine head (4) to its upper position.
Release the turntable (17) by slackening the
locking grip (14).
Use the handle (1) to adjust the turntable (17) to
the angle required (in this connection see also
section 7.2).
Retighten the locking grip (14) to secure the
turntable in place.
Undo the locking screw (21) and use the handle
(1) to tilt the machine head (4) to the left until it
coincides with the required angle value (in this
connection see also section 7.3).
Re-tighten the locking screw (21).
Cut as described under section 7.1.
7.5 Limiting the cutting depth (Fig. 15)
The cutting depth can be infinitely adjusted using
the screw (27). Undo the knurled nut on the screw
(27) and move the stop for limiting the cutting
depth (28) to the outside. Set the required cutting
depth by tightening or undoing the screw (27) and
then tighten the knurled nut on the screw (27).
Check the adjustment by making a test cut.
7.6 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (22) for
sawdust and chips.
The debris bag (22) can be emptied by means of a
zipper at the bottom.
7.7 Changing the saw blade (Fig. 1, 16 – 19)
Remove the power plug!
Swing the machine head (4) upwards and lock it
in this position using the locking pin (25).
Press the release lever (3) and swing up the saw
blade guard (6) to the point where the recess in
the saw blade guard (6) is above the flange bolt
(31).
Press the saw shaft lock (5) with one hand, while
positioning the wrench (C) over the flange bolt
(39) with the other.
Firmly press on the saw shaft lock (5) and slowly
rotate the flange bolt (31) in clockwise direction.
The saw shaft lock (5) engages after no more
than one rotation.
Now, using a little more force, slacken the flange
bolt (31) in the clockwise direction.
12.01.2009 15:45 Uhr Seite 17
Undo the flange bolt (31) and remove it and them
take off the outer flange (32).
Take the saw blade (7) off the inner flange and
pull it out downwards.
Carefully clean the flange bolt (31), outer flange
(32) and inner flange.
Fit and fasten the new saw blade (7) in reverse
order.
Important. The cutting angle of the teeth, in other
words the direction of rotation of the saw blade
(7) must coincide with the direction of the arrow
on the housing.
Check to make sure that all safety devices are
properly mounted and in good working condition
before you begin working with the saw again.
Important. Every time that you change the saw
blade, check to see that it spins freely in the table
insert (12) in both perpendicular and 45° angle
settings.
Important. The saw blade (7) must be changed
and aligned correctly.
7.8 Transport (Fig. 1 – 3)
Tighten the locking grip (14) to lock the turntable
(17).
Press the release lever (3), push the machine
head (4) to the rear and lock it with the locking
bolt (25). The saw is now locked in its lower
position.
Secure the drag function of the saw in its rear
position using the fixing screw for the drag guide
(24).
Carry the equipment by the fixed saw table (18).
Follow the instructions set out in point 6.2 to erect
the machine again.

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
GB
17