Related Manuals for Bloomfield Horizon 0401
Summary of Contents for Bloomfield Horizon 0401
- Page 1 OWNERS MANUAL HOT WATER DISPENSER MODELS: 0401 Hot Water Dispenser Includes: Installation Operation Use & Care Servicing Instructions Model: 0401 PRINTED IN CHINA 77380 Rev.(-) ECN-12917 M714 0913 cps...
-
Page 2: Warranty Statement
The prices charged by Bloomfield Industries for its products installation or eighteen (18) months from the date of shipment are based upon the limitations in this warranty. -
Page 3: Table Of Contents
SPECIFICATIONS AMPS POWER SUPPLY MODEL STYLE VOLTS WATTS 1ø CORD 0401 1800 15.0 HOT WATER NEMA 5-15P DISPENSER 1500 12.5 0401CA meets Canadian Standards APPLICABILITY This manual applies to the following Bloomfield Industries products: 0401, 0401CA, 0401PE... -
Page 4: Features & Operating Controls
FEATURES AND OPERATING CONTROLS - HOT WATER DISPENSER Fig. 1 Features & Operating Controls... -
Page 5: Precautions & General Information
PRECAUTIONS AND GENERAL INFORMATION WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WARNING: INJURY HAZARD All installation procedures must be performed by qualified personnel with full knowledge of all... - Page 6 INSTALLATION READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION IMPORTANT: Unpack the unit. Inspect all components for completeness and To enable the installer to make condition. Ensure that all packing materials have been removed a quality installation and to from the unit. minimize installation time, the following suggestions and tests LEVELING THE UNIT...
-
Page 7: Installation Instructions
NOTE: Water supply inlet line must meet certain minimum criteria to insure successful operation of the brewer. Bloomfield recommends 1/4" copper tubing for installation of less than 12 feet and 3/8" for more than 12 feet from a 1/2" water supply line. - Page 8 INSTALLATION (continued) ELECTRICIAN’S INSTALLATION INSTRUCTIONS WARNING: SHOCK HAZARD REFER TO ELECTRICAL SPECIFICATIONS - Page 1 Check the nameplate to determine correct electrical service Dispenser must be properly required for the Dispenser to be installed. grounded to prevent possible shock hazard. DO NOT IMPORTANT: Before connecting to electricity, make sure assume a plumbing line will Dispenser is connected to the water supply.
-
Page 9: Operation
OPERATION A. START-UP IMPORTANT: TANK MUST BE FULL For initial start-up, or if the dispenser has not been used for an OF WATER BEFORE extended period of time: CONNECTING BREWER ♦ Be sure the water supply is properly connected and the water TO ELECTRIC POWER. - Page 10 OPERATION Fig. 4 Dispenser Operation Diagram WATER HEATER Water temperature is sensed by thermobulb inserted into the water tank. Temperature is controlled by a mechanical thermostat. The setpoint temperature is adjustable by turning the thermostat shaft. Excessive temperature will trip the hi-limit safety switch, disabling the heating element. The hi-limit will automatically reset when the dispenser cools.
-
Page 11: Cleaning Instructions
CLEANING INSTRUCTIONS PROCEDURE: Clean Hot Water Dispenser CAUTION: Burn Hazard PRECAUTIONS: Disconnect dispenser from electric power. Allow dispenser to cool. Dispensed water is extremely hot. Hot water will cause FREQUENCY: Daily serious skin burns. TOOLS: Mild Detergent, Clean Soft Cloth or Sponge Bristle Brush CAUTION: Electric Shock... -
Page 12: Troubleshooting Suggestions
TROUBLESHOOTING SUGGESTIONS SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY Water won’t heat Dispenser unplugged or circuit Check power supply cord breaker tripped Check / reset circuit breaker Tank heater switch "OFF" Press switch to "ON" Temperature setpoint too low Adjust thermostat for desired temperature Hi-Limit safety switch tripped Allow to cool hi-limit will self-... -
Page 13: Servicing Instructions
SERVICING INSTRUCTIONS TEMPERATURE ADJUSTMENT CAUTION: SHOCK HAZARD Disconnect dispenser from electric power. Remove top panel. These procedures involve Pull vent tube out of tank lid and insert a thermometer of known exposed electrical circuits. accuracy in hole. Reconnect dispenser to electrical power. These procedures are to be Place empty container under dispense nozzle. - Page 14 SERVICING INSTRUCTIONS (continued) IMPORTANT: REMOVE TANK LID ASSEMBLY Water pressure must be Disconnect dispenser from electric power. Turn OFF water between 20 p.s.i and 90 p.s.i. supply. Remove top panel. Pull vent tube and inlet elbow out of flowing pressure. If water tank lid.
- Page 15 SERVICING INSTRUCTIONS (continued) REPLACE FILL SOLENOID IMPORTANT: Shut-off water and disconnect dispenser from electric power before removing hoses or wiring. Remove top cover and detach solenoid access door from cabinet. Remove water supply inlet flare fitting Note: Service wrench #86660 is designed to hold the flats of the solenoid inlet fitting while attaching ot removing the flare nut.
-
Page 16: Deliming Instructions
Should deliming the hi-limit thermostat (if removed). Verify that all internal hoses become necessary, components are dry, then reinstall the top panel. Bloomfield recommends 10. Reconnect dispenser to electrical supply and reconnect water replacing the hoses. supply. 11. Place an empty container under the dispense nozzle. -
Page 17: Wiring Diagrams
WIRING DIAGRAM... -
Page 18: Exploded View & Parts List
EXPLODED VIEW & PARTS LIST PLUMBING & RELATED COMPONENTS MODELS: 0401... - Page 19 EXPLODED VIEW & PARTS LIST (continued) CABINET & CHASSIS ELECTRICAL COMPONENTS MODEL: 0401...
- Page 20 Bloomfield Industries proudly supports CFESA Commercial Food Equipment Service Association Bloomfield Industries, Inc. Division of Carrier Commercial Refrigeration In US and Canada Telephone: 775-689-5700 Fax: 888-492-2783 Fax: 800-356-5142 ( for orders only website: www.wellsbloomfield.com PRINTED IN CHINA...