Lucent Technologies 9200 User Manual
  1. Manuals
  2. Brands
  3. Lucent Technologies Manuals
  4. Cordless Telephone
  5. 9200
  6. User manual
Lucent Technologies 9200 User Manual

Lucent Technologies 9200 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O P E R A T I N G
This cordless telephone operates at the maximum power
allowed by the Federal Communications Commission
(FCC). Even so, this handset and base can communicate
over only a certain distance — which can vary with the
locations of the base and handset, the weather, and the
construction of your home or office. For best
performance, keep the base antenna fully extended.
If you receive a call while you are out of range, the
handset might not ring — or if it does ring, the call might
not connect when you press P. Move closer to the
base, then press P to answer the call.
User's Manual for
Cordless Telephone
9200
Fold open this manual for information about
this product's installation and operation.
Please read Part 1 – Important Product
Information, included in this package.
© 1998 Philips Consumer Communications L.P. All rights reserved.
Printed in China. 108058207 Issue L2
R A N G E
If you move out of range during a phone
conversation, you will hear noise or interference. To
improve reception, move closer to the base.
If you move out of range without pressing o, your
phone will be left "off the hook." To hang up properly,
walk back into range, periodically pressing o.
This cordless phone has ten channels available for
maximum performance.
4
Part 2

Advertisement

Table of Contents
loading

Related Manuals for Lucent Technologies 9200

Summary of Contents for Lucent Technologies 9200

  • Page 1 P. Move closer to the base, then press P to answer the call. User's Manual for Cordless Telephone 9200 Fold open this manual for information about this product’s installation and operation. Please read Part 1 – Important Product Information, included in this package.

  • Page 2: Installation

    I N S T A L L A T I O N Standard Modular electrical telephone outlet jack Telephone line cord Power cord Table/Desk Installation Connect the power cord. Plug the power adapter into the jack on the back of Choose a spot near an electrical outlet and a the base.

  • Page 3: Wall Installation

    I N S T A L L A T I O N Wall Installation Mount the telephone on the wall. Position the telephone base so the mounting studs on Follow Steps 1-3 under Table/Desk Installation. the wall jack fit into the base of the telephone. Slide Remove the reversible base.
  • Page 4 C A S E D I F F I C U L T Y If the phone does not ring when you receive a call: If you have difficulty operating this phone, try the suggestions below. If you still have trouble, call •...

  • Page 5: Operation

    T E L E P H O N E O P E R A T I O N Latch for Spare Battery Handset Volume Compartment Control Headset jack Light goes on Make or answer when system is a call End a call connected to Change channels power and...

  • Page 6: Page/Handset Locator

    (For best to use the Temporary Tone feature. results, use only Lucent Technologies Accessory If you have dial pulse (rotary) service, this feature allows Headset with 2.5 mm plug.) Do not force the you to enter codes or tones needed to operate answering connection, but make sure the plug fits securely.

  • Page 7: Storing Memory Numbers

    T E L E P H O N E M E M O R Y Storing a Pause in a Memory Number This cordless phone can store 10 telephone numbers that you can dial just by pressing m and a number button. While storing a number in memory, hold down the button of the number that comes before the pause until you hear Storing Memory Numbers...

  • Page 8: Charging The Handset Battery Pack

    B A T T E R I E S CAUTION: To reduce the risk of fire or injury to Replace the battery door. The SPARE BATTERY light persons or damage to the telephone, read and on the base goes on, and the spare battery will be follow these instructions carefully.

Table of Contents