Page 1
User s Manual for ’ Cordless Telephone with Caller ID/Call Waiting 9125 Part 2 Please read Part 1 — Important Product Information, included in your package. Lucent 9125 cover.L1 4/8/98, 11:31 AM...
TONE. If you have dial pulse (rotary) service, set the switch to PULSE. Even if you have dial pulse service, you can still use telephone services requiring tone signals. See “Temporary Tone” in the OPERATION section of this manual. Lucent 9125 book.L1 INSTALLATION Modular Telephone...
Follow Steps 1–3 under Table/Desk Installation. Turn the base unit over, and attach the wall mounting base to the lower half of the base unit. Gently press down until it snaps firmly into place. Lucent 9125 book.L1 4/8/98, 11:25 AM...
Follow Steps 6 and 7 under Table/Desk Installation. CAUTION: Use only the AC power adapter supplied with this telephone, Power Supply for 9125. Input: AC 117V, 60 Hz, 12W Output: DC 11V, 500mA. Belt Clip If you wish, you can attach the belt clip to the cordless handset, following the illustrations below.
TELEPHONE OPERATION Light goes on when handset is in use, or when handset is charging in base Directory card Lucent 9125 book.L1 Send paging tone to handset Light goes on when spare battery (optional) is placed in Spare Battery Compartment...
Page 9
Caller ID service Access numbers in telephone memory Redial last number called Store numbers in telephone memory Allows you to hear caller, but caller doesn’t hear you Remove one or all calls from Call History Lucent 9125 book.L1 4/8/98, 11:25 AM...
Press and release H again to return to the call. Mute Press and release M. The screen displays MICROPHONE MUTED. You can hear the caller, but the caller can’t hear you. Press and release M again to return to two-way conversation. Lucent 9125 book.L1 4/8/98, 11:25 AM...
To be sure, ask the company that provides the special service. Dial the call, then press *. Any buttons pressed after this send tone signals. After you hang up, the phone automatically returns to dial pulse (rotary) dialing. Lucent 9125 book.L1 4/8/98, 4:03 PM...
Follow instructions under “Making a Call” or “Answering a Call.” NOTE: The earpiece and microphone on the handset are disabled when the headset is plugged in. Lucent 9125 book.L1 4/8/98, 11:25 AM...
OPERATING RANGE This cordless telephone operates at the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office.
Enter the memory location (01–20) of the number you’re calling. Memory Guard The phone numbers you store in memory are protected from loss when you change the handset battery, or in the event of a power failure. Lucent 9125 book.L1 4/8/98, 11:25 AM...
The caller may be out of your call service area. PRIVATE The caller has blocked call information from being sent. TRANSMISSION There is a problem with the transmission of ERROR information being sent. Lucent 9125 book.L1 CALLER ID OPERATION 4/8/98, 11:25 AM...
Enter the area code you need (for example, 1 973) if necessary. Press and release C. Use < or > to locate the caller you want. Press and release P to dial the number. Lucent 9125 book.L1 , press 9 to see the information 4/8/98, 11:25 AM...
When you install a spare battery (purchased separately) in the base, you can use this phone even during a power failure. If the battery in the spare battery compartment is fully charged, you can make and receive calls for up to five hours. Lucent 9125 book.L1 BATTERIES 4/8/98, 11:25 AM...
Place the handset in the base and allow it to charge for 16 hours. Your telephone might operate before that, but for best performance, let the handset battery pack charge fully. Charging the spare battery pack Lucent 9125 book.L1 Replacing the handset battery pack 4/8/98, 11:25 AM...
IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. If you still have trouble, call 1 800 PCC–9125. If the phone doesn’t work at all, check these items first: • Make sure the AC adapter is plugged into an outlet not controlled by a wall switch.
Page 20
Disconnect the base from the modular jack and plug in a corded telephone. If you still hear other calls, the problem is probably in your wiring or local service. Call your local telephone service company. Lucent 9125 book.L1 4/8/98, 11:26 AM...