Danby DDW2405W Installation Instructions Manual
Built-in
Hide thumbs
Also See for DDW2405W:
- Instruction manual (15 pages) ,
- Installation instructions manual (13 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Installation Instructions
BEFORE YOU BEGIN:
STOP
these instructions completely
and carefully.
IMPORTANT:
Observe all governing codes
and ordinances.
Note to the Installer:
these instructions for the consumer's and local
inspectors use.
Note to Consumer:
with your Owner's Manual for future reference.
Skill Level: I
nstallation of this dishwasher
requires basic mechanical and electrical skills.
Proper installation is the responsibility
of the installer. Product failure due to
improper installation is not covered
under the Dishwasher Warranty.
Completion Time 1 to 3 Hours.
New installations require more time than
replacement installations.
Read
Be sure to leave
Keep these instructions
Built-In Dishwasher
Model(s):
DDW2405W DDW2405BL DW2406BLS
IMPORTANT:
The dishwasher MUST be installed to
allow for removal from the enclosure in the event
future service is required.
FOR YOUR SAFETY: Read and observe all
CAUTIONS and WARNINGS shown throughout
these instructions. While performing
installations described in this booklet, gloves,
safety glasses or goggles should be worn.
WARNING:
of electrical shock, fire or
injury to persons, the installer
must ensure that the dish-
washer is completely enclosed
at the time of installation
READ CAREFULLY.
KEEP THESE
INSTRUCTIONS.
To reduce the risk
ver. 1 07.19.04
Advertisement
Table of Contents
Related Manuals for Danby DDW2405W
Summary of Contents for Danby DDW2405W
- Page 1 Installation Instructions Built-In Dishwasher Model(s): DDW2405W DDW2405BL DW2406BLS IMPORTANT: The dishwasher MUST be installed to BEFORE YOU BEGIN: Read allow for removal from the enclosure in the event STOP these instructions completely future service is required. and carefully. IMPORTANT: Observe all governing codes FOR YOUR SAFETY: Read and observe all and ordinances.
-
Page 2: Parts Supplied
Installation Preparation PARTS SUPPLIED: 2 Wood Screws • Two #8 Phillips flat head wood screws 5/8” long to secure dishwasher to underside of countertop. (Screws can be found inside the literature package) MATERIALS YOU WILL NEED: (Not included) • Ferrule, compression nut and elbow (3/8”... -
Page 3: Prepare Dishwasher Enclosure
INSTALLATION PREPARATION PREPARE DISHWASHER ENCLOSURE • The dishwasher must be installed so that the drain hose is no more than 10 feet in length for proper drainage. • The dishwasher must be fully enclosed on the top, side and back, and must not support any part of the enclosure. - Page 4 INSTALLATION PREPARATION PREPARE ELECTRICAL WIRING WARNING: FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. Electrical Requirements: • This appliance must be supplied with 120V / 60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.
-
Page 5: Installation Instructions
INSTALLATION INSTRUCTIONS PREPARE HOT WATER LINE: STOP • The hot water line may enter from either side, rear or floor within the shaded area shown in Fig. 6 BEFORE YOU BEGIN • The line may pass through the same hole as the Locate and set aside the package containing the electrical cable and drain hose. -
Page 6: Step 2 Adjust Leveling Legs
INSTALLATION INSTRUCTIONS STEP 2 ADJUST LEVELING LEGS STEP 4 INSTALL 90 ELBOW Wrap the 90 o elbow with thread seal tape, then install it onto the water valve. To avoid damage to the water valve bracket and/or fitting, do not over- tighten the 90 o elbow. -
Page 7: Step 7 Slide Dishwasher Partially Into Cabinet
INSTALLATION INSTRUCTIONS STEP 6 INSERT DRAIN HOSE THROUGH CABINET • Position the dishwasher in front of he opening. Insert drain hose into cabinet wall hole. TIP: Position water line and house wiring on the floor to avoid interference with base of dishwasher. STEP 7 SLIDE DISHWASHER PARTIALLY INTO CABINET TO AVOID DAMAGING THE FRONT PANEL, DO NOT PUSH CABINET IN WITH KNEES. -
Page 8: Step 8 Position Dishwasher Under Countertop
INSTALLATION INSTRUCTIONS STEP 8 POSITION DISHWASHER UNDER COUNTERTOP • Check to be sure that wires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. TIP: Check tub insulation blanket. It should be positioned so it is not bunched up or interfering with door springs. - Page 9 INSTALLATION INSTRUCTIONS STEP 10 SECURE DISHWASHER STEP 11 CONNECT WATER TO CABINET SUPPLY Connect water supply line to 90 o elbow. The dishwasher must be secured to Method 1 - Braided flex hose the countertop. • Connect the stainless steel braided flex hose •...
-
Page 10: Step 12 Connect Drain Line
INSTALLATION INSTRUCTIONS DRAIN LINE INSTALLATION STEP 12 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES • Connect drain line to air gap, waste tee or disposer AND ORDINANCES using either of the previously determined method. The drain hose molded end will fit 5/8”, 3/4” or 1” Method 1 - Air gap with waste tee or disposer diameter connections on the air gap, waste tee or disposer. -
Page 11: Step 13 Connect Power Supply
INSTALLATION INSTRUCTIONS STEP 13 CONNECT POWER SUPPLY STEP 14 PRE-TEST CHECK LIST Review this list after installing your dishwasher • Remove junction box Cover “ A “. to avoid charges for a service call that is not • Locate the three dishwasher wires, (white, black and covered by your warranty. -
Page 12: Step 15 Dishwasher Wet Test
INSTALLATION INSTRUCTIONS STEP 15 DISHWASHER WET TEST Turn on power. Make sure door is closed. Select “Normal” wash program. Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on.