Table of Contents
Advertisement
Remaining small ice and frost stains on back plate
of the refrigerator after defrosting period is not
abnormal.
The freezer can not be equipped with automatic
defrosting set since the deep-frozen and frozen
foods do not endure melting temperature.
When small frost and ice occurs scrape off and
remove frost and ice coating with the supplied
plastic scraper.
The tray in figure is not a piece of accessories to
the appliance!
When ice coating is so thick that it cannot be
removed with the plastic scraper, the cooling plate
has to be defrosted. Frequency of defrosting
depends on usage (generally 2-3 times a year).
Take the frozen foods out of the appliance, and put
them into a basket lined with paper or cloth. Store
them in a possibly cool place or replace them into
another refrigerator.
Pull out the mains plug from the mains socket, so
both parts of the appliance are out of operation.
Open the doors of both parts of the appliance and
clean the refrigerator according to Regular
cleaning. Maintain and clean the freezer as
following:
Sweep the melting water with a cloth or sponge
off the cooling plate. The melting water swept
down gathers in the bottom of the appliance and
can be removed with a hygroscopic cloth or a
sponge
Wipe the surfaces after defrosting.
Put the mains plug into the mains socket and put
foods taken out back to their places.
It is recommended to operate the appliance at the
highest position of the thermostatic control for
some hours so that it can reach the sufficient
storing temperature as soon as possible.
Regular cleaning
It is recommended to wash the inside of the
refrigerator in 3-4 weeks time using lukewarm
water then wipe it (it is practical to clean the inside
of the freezer and defrost it at a time).
Household cleaner or soap must not be used.
After breaking the circuit wash the appliance with
lukewarm water then wipe it. Clean the door
gasket with clean water. After cleaning apply
voltage to the appliance.
It is recommended to remove the dust and dirt
collected on the back of the refrigerator and the
condenser and to clean the evaporative tray on top
of the compressor once or twice a year.
When the refrigerator is not in use
In case the appliance will not be used for a long
time, follow these steps:
Break the circuit of the appliance.
Remove foods from the refrigerator.
Defrost and clean it as written before.
Leave the door open to avoid a build up of air
inside.
Trouble shooting
How to change the bulb
Should the light fail to work you can change it as
below:
Break the circuit of the appliance.
Press the front hook and at the same time slide the
cover in the direction indicated by horizontal
arrow (1), than remove cover by pulling it gently
down as indicated by arrow (2). So the bulb can be
replaced. (Bulb type: 230-240 V, 15 W, F 14
thread)
After changing the bulb replace the cover, snap it
in place and apply voltage to the appliance.
7
If something does not work
During operation of the appliance some smaller
but annoying trouble can often occur, which does
not require calling a technician out. In the
following chart information is given about them
to avoid unnecessary charges on service.
We draw your attention that operation of
appliance goes with certain sounds (compressor-
and circulating sound).
Problem
Thermostatic control can be set wrongly.
If products are not cold enough or placed
It is too warm in the refrigerator
wrong.
The door does not close tightly or it is not
shut properly.
Thermostatic control can be set wrongly.
The door does not close tightly or it is not
shut properly.
It is too warm in the freezer
Products in big quantity to be frozen
were put in.
Products to be frozen are placed too
closely to each other
It is normal. During automatic defrosting
frost melts on the back plate.
The outlet of the chamber can be
Water flows at the back plate of the
clogged up. Products placed in can
refrigerator
prevent water from flowing into the
Water flows into the chamber
collector
Water flows onto the floor
The melting water outlet flows not into
the evaporative tray above the
compressor
Products are not wrapped properly.
Doors are not shut properly or do not
There are too much frost and ice.
close tight.
The thermostatic control can be set
wrongly.
The thermostatic control is set wrongly.
Doors are not shut properly or do not
The compressor operates
close tight.
continually.
Products in big quantity to be frozen
were put in.
Too warm food was put in.
The appliance is in too warm place.
The appliance does not work at all.
Plug is not connected to the mains
Neither cooling, nor lighting works.
socket proper.
Indicator lamps do not give light.
The fuse burnt out.
The thermostatic control is not on.
There is no voltage in the mains socket.
The appliance is noisy.
(Try to connect another appliance into it.)
The appliance is not supported properly.
In as much as the advice d oes not lead to result, call the nearest brand-mark service.
This is not trouble, but means normal operation.
!
We draw it to your attention again that the
appliance operates discontinuously, so the
stopping of compressor does not mean being no-
current. That is why you must not touch the
electrical parts of the appliance before breaking
the circuit.
Possible cause
Solution
Set the thermostat knob to higher
position.
Place the products to the appropriate
place.
Check if the door closes well and the
gasket is unhurt and clean.
Set the thermostat knob to higher
position. Check if the door closes well
and the gasket is unhurt and clean.
Wait some hours and then check the
temperature again.
Place the products in a way so that
cold air could circulate among them.
Clean the outlet.
Replace the products so that they can
not touch the back plate directly.
Put the melting water outlet to the
evaporative tray.
Wrap the products better
Check if the doors close well and the
gaskets are unhurt and clean.
Set the thermostat knob to a position
that gives higher temperature.
Set the thermostat knob to a position
that gives higher temperature.
Check if the doors close well and the
gaskets are unhurt and clean.
Wait some hours and then check the
temperature again.
Put food at max. room temperature.
Try to reduce the temperature in the
room where the appliance stands.
Connect the mains plug properly.
Change the fuse.
Start the appliance according to
instructions in chapter Putting it into
use".
Call an electrician.
Check if the appliance stands stable
(all the four feet should be on the floor).
8
Advertisement
Table of Contents
