System Connections; Connecting To A Satellite Receiver; Connecting To A Dolby Digital Decoder Or An Amplifier With Built-In Dts - JVC DR-MH20S Instructions Manual

SYSTEM CONNECTIONS

70
EN

Connecting To A Satellite Receiver

Connect the satellite receiver to the [L-2 IN/DECODER] connector,
then connect the [L-1 IN/OUT] connector to the TV's connector.
NOTES:
●
Set AL-2 SELECTB to AVIDEOB or AS-VIDEOB. (A pg. 67)
●
You can use the Automatic Satellite Programme Recording
function (A pg. 51) with this connection. (HDD deck only)
●
To record a programme via the satellite receiver, select L-2 mode
by pressing PR +/– so that AL-2B appears on the front display
panel.
●
For details, refer to the instruction manual of the satellite
receiver.
Outdoor unit
Satellite cable
Satellite receiver
TV
IMPORTANT
When you set AL-2 SELECTB to ASAT VIDEOB or ASAT S-VIDEOB
(A pg. 67), it is possible to view a satellite broadcast with the TV
set to its AV mode even if the unit is turned off. When the unit is
in Stop mode or recording, press TV AV/VIDEO on the remote
control to turn off the VIDEO lamp on the unit.
●
If you turn on the unit when the satellite receiver's power is off,
nothing appears on the TV screen. In this case, turn on the
satellite receiver, or set the TV to its TV mode, or press TV AV/
VIDEO on the remote control to set the unit to the AV mode.
Aerial
TV aerial cable
ANTENNA IN
ANTENNA OUT
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
Dolby Digital Decoder or
amplifier with built-in DTS
To [DIGITAL AUDIO OUT
Rear of unit
1
Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
●
For Dolby Digital sound, set ADIGITAL AUDIO OUTB to ADOLBY
DIGITAL/PCMB. (A pg. 71)
●
For DTS sound, set ADIGITAL AUDIO OUTB to ASTREAM/PCMB.
(A pg. 71)
CAUTIONS:
●
This unit has a dynamic range of more than 110 dB with regards
to its Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to
the speakers may damage them.
●
Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do
not place the speakers adjacent to the TV set as this can
adversely affect the playback picture.
When you can't switch the audio channel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional optical cable and ADIGITAL AUDIO OUTB is set to
ADOLBY DIGITAL/PCMB, it is not possible to switch the audio
channel of a bilingual programme recorded on a DVD-RAM or
DVD-RW (VR mode) disc. In this case, perform the following steps
using the remote control to switch ADIGITAL AUDIO OUTB from
ADOLBY DIGITAL/PCMB to APCM ONLYB.
A Press SET UP to access the Main Menu screen.
B Press selection keys to select ADVD VIDEO SET UPB, then press G.
C Press selection keys to select AAUDIO OUTPUTB, then press G.
D Press selection keys to select ADIGITAL AUDIO OUTB, then
press ENTER.
E Press selection keys to select APCM ONLYB, then press
ENTER. (A pg. 71)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
To DIGITAL AUDIO
input
Optical cable
Coaxial cable
(not supplied)
(not supplied)
To [DIGITAL
AUDIO OUT
(OPTICAL)]
(COAXIAL)]
Note for connection:
Remove the protection cap
from the optical cable.