Page 1
LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-02A Rev. A Emulex Connects™ Servers, Storage and People...
Page 2
Information furnished by Emulex is believed to be accurate and reliable. However, no responsibility is assumed by Emulex for its use; or for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent, copyright or related rights of Emulex.
List of Tables Table 1-1 Software and Hardware Environments..........7 Table 2-1 Media Specifications ..............11 Table 2-2 POST Conditions and Results ............14 Table 3-1 LPe15004, LPe16004, and LPe16000B–series HBA Specifications ....15 LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-02A Rev. A...
LPe16000B, LPe16002B, and LPe16004, 16 Gb/s The core technology of these HBAs is Emulex's 10th generation FC controller. The controller is a multi-function PCIe Gen3 interface controller that is compliant to the PCI Express Base Specification Rev 3.0 and PCI Express CEM Specification Rev 3.0. The LPe16000B is a single-channel adapter, the LPe16002B is a dual-channel adapter, and the LPe15004 and LPe16004 are four-channel adapters.
Use PCIe Gen 3 compliant systems that are x8 or x16 lane at up to 8 GT/s per lane. HBA Identification Each HBA ships with several numbers clearly marked on the board. Emulex recommends recording these numbers before installation. Serial number – assigned by Emulex. Use this number when communicating ...
3.11 inches (7.9 cm) compared to 4.75 inches (12.06 cm) long. Note: On the LPe15004 HBA, you can remove and change the bracket but you cannot remove the optical transceiver.
Figure 2-3 shows an extracted transceiver and another transceiver latched in place. Figure 2-3 Removing an Optical Transceiver 3. Observing Electrostatic Discharge (ESD) precautions, store the transceiver in an ESD-safe place. LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-02A Rev. A...
3. Remove the blank panel from an empty PCIe bus slot. See “Preparing the HBA for Installation” on page 8 to change the brackets if needed. Otherwise, proceed to “Attaching Media” on page 11. LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-02A Rev. A...
2. After the appropriate cable is connected to the HBA, connect the other end to the FC device. After the cable is connected to the HBA, you are ready to apply power to the computer. LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-02A Rev. A...
Figure 2-7 Optical HBA LED Indicators POST Conditions and Results POST is the default mode of self-test for the LPe15004, LPe16004, and the LPe16000B-series HBAs. No jumpers or connectors are necessary for this test to run. These tests perform a quick confidence level check of the HBA before running the operational software.
Not Defined Slow Blink Flashing Not Defined Fast Blink Not Defined Fast Blink Not Defined Fast Blink Slow Blink Not Defined Fast Blink Fast Blink Beaconing Fast Blink Flashing Not Defined LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-02A Rev. A...
3. References LPe15004, LPe16004, and LPe16000B–series HBA Specifications 3. References LPe15004, LPe16004, and LPe16000B–series HBA Specifications The specifications of the LPe15004, LPe16004, and LPe16000B–series HBAs are listed in Table 3-1. Table 3-1 LPe15004, LPe16004, and LPe16000B–series HBA Specifications Parameter Range Physical Dimensions LPe16000B-series and LPe15004 HBAs: Low-profile form factor, 6.600 inches...
The reader is cautioned that changes or modifications made to the equipment not expressly approved by Emulex LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual...
Page 17
Notice for South Korea and Translations (KCC) Translation: Sellers and users of this equipment take note that this equipment is EMC approved for Class A industrial use, and as such is not intended for residential use. LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-02A Rev. A...
Note: Changes or modifications not expressly approved by Emulex Corporation, including the use of non-Emulex approved optical transceivers, could void the user's authority to operate this equipment. LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual...
Page 19
This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures. Changes or modifications not expressly approved by Emulex Corporation could void the user's authority to operate this equipment.
EN/IEC 60825-1. Class 1 laser devices are not considered to be hazardous. The use of non-Emulex approved optical transceivers, or transceivers which do not comply with the Class 1 radiation performance requirements defined in DHHS/CDRH 21CFR Sub-chapter J and IEC 60825-1, may expose the user to hazardous laser radiation, and such devices should not be used with Emulex products.
Need help?
Do you have a question about the LPe15004 and is the answer not in the manual?
Questions and answers