Emulex LPe12000 Installation Manual
Host bus adapter
Hide thumbs
Also See for LPe12000:
- Datasheet (2 pages) ,
- User manual (69 pages) ,
- Troubleshooting and maintenance manual (23 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Emulex LPe12000
Summary of Contents for Emulex LPe12000
- Page 1 LPe12000 and LPe12002 Installation Manual Last updated January 29, 2008...
- Page 2 Emulex Corporation for its use; or for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Emulex Corporation.
-
Page 3: Table Of Contents
Viewing the LEDs ... 6 POST Conditions and Results ... 6 References ... 8 Specifications ... 8 FCC and Regulatory Notices ... 9 Declaration of Conformity ... 10 Laser Safety Notice ... 12 LPe12000 and LPe12002 Hardware Installation Manual Page iii... -
Page 4: Introduction
The LPe12002 is a dual-channel adapter. The core technology of these HBAs is the ninth generation FC controller by Emulex. The controller incorporates a multifunction native PCIe core that is compliant to the PCIe Base Specification 2.0 and PCI Express CEM Specification 2.0. -
Page 5: Setting The Jumpers
1 and 2, or 3 and 4, or 5 and 6. If no jumper is installed, the default device ID is 0x1AE5. Table 1. Jumper Settings (Port 0 on the LPe12000 - Ports 0 and 1 on the LPe12002) PCI Identifier... -
Page 6: Installing The Host Bus Adapter
Installing the Host Bus Adapter The Emulex LPe12000 and LPe12002 host bus adapters (HBAs) use a removable optical transceiver. If you need to change the bracket for HBA installation, you must first remove this transceiver from its housing (cage). This document explains how to install the HBA and, if necessary, how to remove the transceiver and bracket safely. - Page 7 16. Secure the HBA's mounting bracket to the case with the panel screw or clip. 17. Replace the computer case and tighten case screws. The HBA is now installed in the PC and is ready for media attachment. LPe12000 and LPe12002 Hardware Installation Manual Page 4...
-
Page 8: Attaching Media
2. Connect the other end of the cable to the Fibre Channel device. After the media is connected to the HBA, you are ready to apply power to the computer. LPe12000 and LPe12002 Hardware Installation Manual Maximum Length Minimum Length .5 meters... -
Page 9: Applying Power
Table 8. POST Conditions and Results Yellow LED Slow Blink Fast Blink Flashing 2 Fast Blinks 3 Fast Blinks LPe12000 and LPe12002 Hardware Installation Manual Port 0 LEDs Port 1 LEDs Green LED Wake-up failure (Dead board) POST failure (Dead board) - Page 10 Slow Blink Slow Blink Fast Blink Slow Blink Flashing Slow Blink LPe12000 and LPe12002 Hardware Installation Manual Green LED 8Gb Link rate-Normal, link up Normal-link down or not started Off-line for download Restricted off-line mode (Waiting for restart) Restricted off-line mode (Test active)
-
Page 11: References
References Specifications Table 9. LPe12000 and LPe12002 Specifications Parameter Media Interface The controller interfaces to the physical media through an FC-0 Media Interface (FC-PI compliant transceiver), and then connects through dual optical fiber LC connectors. Physical Dimensions Low-profile MD2 form factor, 6.600 inches by 2.713 inches, and accommodates both the full-height and low-profile bracket. -
Page 12: Fcc And Regulatory Notices
The reader is cautioned that changes or modifications made to the equipment not expressly approved by Emulex could void the user's authority to operate this equipment. The above statement applies to products marketed in the USA. -
Page 13: Declaration Of Conformity
WARNING: This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures. Note: Changes or modifications not expressly approved by Emulex Corporation could void the user's authority to operate this equipment. - Page 14 LPe12000 and LPe12002 Hardware Installation Manual Page 11...
-
Page 15: Laser Safety Notice
PCIe expansion slot. In the United States, all optical small form factor transceivers sold by Emulex are certified as Class 1 laser products that conform to the requirements contained in the Department of Health and Human Services (DHHS) regulation 21 CFR subchapter J. -
Page 16: Product Information
Short wavelength and long wavelength small form factor transceivers embedded in Emulex host adapter are non-OFC. For non- OFC links, a compatible laser device must be non-OFC and certified as a Class 1 laser product. - Page 17 Copies of the certificate of conformity for any small form factor transceiver sold by Emulex can be obtained upon request from Emulex Corporation, Costa Mesa. LPe12000 and LPe12002 Hardware Installation Manual...