Remote Control (Vsx-839Rds) - Pioneer VSX-839RDS Operating Instructions Manual

Displays & Controls

Remote Control (VSX-839RDS)

1
2
3
4
5
6
7
8
9
0
-
=
~
!
@
#
$
1
SOURCE button
Use to turn on/off other components connected to
the receiver.
2 MULTI CONTROL buttons
Use to put the receiver/remote control in the
stated mode.
For other equipment controls, see "Using the
Remote Control with Other Components" on
pages 77 – 83.
3 NUMBER/MODE buttons
Use the number buttons to select the radio
frequency in tuner DIRECT ACCESS mode or the
tracks in CD, DVD mode etc.
Also, buttons marked with the following names
have special functions. If you try to use one of
these functions but the display flashes it means that
function cannot be used in the current mode (for
example DSP modes cannot be used when 5.1 CH
setting is on).
LOUDNESS button
Use to switch on the loudness. This feature is
useful for getting good bass and treble sounds
listening at low volumes.
26
En
SOURCE RECEIVER
VCR VCR
DVD TV
1 2
MULTI CONTROL
CD CD-R TUN TVC
1 2 3
LOUDNESS VIDEO SELECT MULTI CH INPUT
4 5 6
INPUT ATT DIGITAL NR FL DIMMER
7 8 9
REMOTE SETUP SYSTEM SETUP SIGNAL SELECT
+10 0
DISC
EFFECT/CH SEL
RECEIVER
TV
TV VOL MASTER VOLUME
TV CONTROL
TVFUNK
4 ¢
CHANNEL
TUNE
ST ST
ENTER
TUNE
TOP MENU MENU
D.ACCESS BAND CLASS
& ‹ *
MPX DISPLAY RF ATT
¶ ! ⁄
RETURN SETUP CLEAR AUDIO
RECEIVER DIRECT CONTROL
MIDNIGHT DSP STEREO FUNCTION
THX ADVANCED STANDARD MUTE
2
Î
/ DTS / MPEG
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
VIDEO SELECT button
%
Switches the receiver between the various
types of video input.
^
MULTI CH INPUT button (See p. 34, 55)
Use to hook up an external component that can
decode other types of signals and input them
into the VSX-839RDS.
INPUT ATT button
Use to lower the input level of an analog signal
that is too powerful, thus causing the sound to
&
distort (the OVERLOAD indicator will light
when this is the case).
*
DIGITAL NR button
Press to switch Digital NR on or off (see page
52).
FL DIMMER button (See p. 56)
Use to adjust the brightness of the fluorescent
display (FL = fluorescent display).
(
Four levels of the brightness ranging from very
)
dim to very bright can be selected. Each press
_
changes the brightness of the display.
+
REMOTE SETUP button
¡
Use to customize the remote control functions
™ and the remote control itself (see "Setting Up
the Remote Control to Control Other Compo-
£
nents" starting on p. 68).
¢
SYSTEM SETUP button
∞
Use to set up the speaker and sound systems.
For more information see "Setting up for
Surround Sound" starting on p. 30.
SIGNAL SELECT button
Press SIGNAL SELECT repeatedly to select one
of the following:
ANALOG – Analog signal.
DIGITAL – Digital signal (DVD/LD, TV/SAT, CD,
CD-R/TAPE 1/MD, VCR 1/DVR, VCR 2).
AUTO – This is the default. If there are analog
and digital input signals, the receiver automati-
cally selects the best possible signal.
EFFECT / CH SEL button
For DSP/advanced theater sound modes use to
put into the mode to add or subtract the amount of
effect. For other sound modes use to select
individual channels to increase or decrease
channel level.
EFFECT +/– buttons
Use to add or subtract the amount of effect in
different DSP/advanced listening sound modes or
the level of individual channels.
4 The following set of four buttons are
dedicated to TV control They are only
for controlling your TV.