Casio Privia PX-5S User Manual page 21

To apply an effect to a tone
1.
Select the tone to which you want to apply the
effect.
2.
Press the cm (EFFECT, SONG) button as
many times as necessary until the indicator
lamp on the EFFECT side is lit.
3.
Press one of the buttons below, depending
on the type of effect you want to apply.
A) DSP: cn (DSP) button
B) SYSTEM: co (SYSTEM) button
cp
C) MASTER: (MASTER) button
This displays an effect setting screen. The screenshot
below shows the screen when configuring SYSTEM
settings.
• A button lamp will not light when you press the
(DSP), co (SYSTEM), or
• To find out whether an effect is on or off, check the
effect type and setting.
• The effect screen can also be displayed from the stage
setup editing screen (page E-31).
4.
Use the ds (u),
(i) buttons to select a setting item.
• For details about editable parameters, see "Editable
DSP Parameters", "Editable SYSTEM Parameters",
and "Editable MASTER Parameters", starting from
page E-19.
• If ">ENT" is on the display, it means that there are
more parameters that can be edited in the operation
you are performing. In this case, pressing the
(ENTER) button will advance to the next editing
page.
5.
Change parameters as desired.
cp (MASTER) button.
dt (w), ek (q), and
6.
After you finish with your edits, press the
(EXIT) button.
• Press the
to return to the screen where you were before you
started editing.
Temporarily Bypassing the DSP
Use the procedure below to temporarily bypass the
DSP and switch the currently selected zone tone to one
without the DSP effect applied.
• You can bypass the DSP for each tone of each zone.
1.
Hold down the
flashes.
2.
To cancel the bypass, hold down the
(DSP) button again until its lamp goes out.
• Note that bypass is canceled even if you change to a
different stage setup.
■ Editable DSP Parameters
• Select "Through" if you want to disable application
of DSP.
• You can select different DSP effects for Parts 1
through 4.
• Parts 5 through 16 do not support use of DSP effects.
- -: Through
Select this option if you do not want to apply a DSP effect. There are
no parameters that can be set while this option is selected.
01: Equalizer
This is a three-band equalizer.
Parameter Value Ranges:
1 :EQ1 Frequency (1.0k, 1.3k, 1.6k, 2.0k, 2.5k, 3.2k, 4.0k, 5.0k [Hz])
Adjusts the center frequency of Equalizer 1.
2 :EQ1 Gain (–12 to 0 to +12)
cn
Adjusts the gain of Equalizer 1.
3 :EQ2 Frequency (1.0k, 1.3k, 1.6k, 2.0k, 2.5k, 3.2k, 4.0k, 5.0k [Hz])
Adjusts the center frequency of Equalizer 2.
4 :EQ2 Gain (–12 to 0 to +12)
Adjusts the gain of Equalizer 2.
5 :EQ3 Frequency (1.0k, 1.3k, 1.6k, 2.0k, 2.5k, 3.2k, 4.0k, 5.0k [Hz])
Adjusts the center frequency of Equalizer 3.
el
6 :EQ3 Gain (–12 to 0 to +12)
Adjusts the gain of Equalizer 3.
7 :Input Level (0 to 127)
Adjusts the input level.
8 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
9 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
Note: The Gain value is not a dB value.
em
Using Built-in Tones (Tutorial)
dr (EXIT) button as many times as required
cn (DSP) button until its lamp
dr
cn
E-19