Casio Privia PX-5S User Manual page 36

Using the Stage Setups (Tutorial)
Display Text
Master Effect Edit >Ent
Compressor Edit
>Ent
Equalizer Edit >Ent
Common Edit >Ent
Tempo
Phrase
Arpeggio
Hammer Response
Knob1 Edit >Ent
Target
Min Value
Max Value
Knob2-4 Edit >Ent
E-34
Master effect parameter. This is a group of editable master effect parameters
(page E-23). For details about group items, see "Editable MASTER
Parameters" (page E-23).
Compressor edit. This is a group of editable compressor parameters within
master effects.
Equalizer edit. This is a group of editable equalizer parameters within
master effects.
This is a group of editable pedal, PRN, and NPRN parameters.
Tempo. Adjusts the phrase playback speed. You also can change the phrase
playback tempo using the
Phrase number. Selects the phrase of the Phrase Sequencer (page E-29).
Preset arpeggio type selection. See "To use the Arpeggio Function" in the
separate USER'S GUIDE (Basics).
Hammer response. Adjusts hammer response within the range of 0 (fast) to
7 (slow).
Knob 1 (Knob 1 edit). This is a group of
Editing can be performed even when the "Knob 1 Enable" setting is "Off".
Target. Selects the parameters to be controlled by a controller. For example,
the "CC67:Soft" setting specifies a soft pedal effect.
• Two targets can be specified for a single controller. Use the
minus (–), plus (+) buttons to switch between Target 1 and Target 2.
No Assign: No target specified.
CC00 to CC97: MIDI control change*
NRPN, RPN: MIDI NRPN and RPN parameters*
Ch.Pressure: MIDI channel pressure*
Tempo: Tempo setting (page E-30)
EQ Low Gain - EQ High Gain: Master EQ >Low Gain - High Gain (page
E-23)
DSP Bypass: Temporarily bypasses the DSP of the currently selected zone.
Ext.Volume: Control the External Volume value.
Layer Detune: Layer detune (page E-17)
Layer1 Volume - Layer6: Tone parameter settings of each layer
• The following can be assigned: Volume (Volume), Pan (panning), OctShift
(octave shift), DspOnOff (DSP on/off), LfoPitch (LFO pitch), LfoFiltr (LFO
filter), LfoAmp (LFO amp). For details about each setting, see the editable
parameters under "Using Built-in Tones (Tutorial)" on page E-10.
Dsp Param 1-16: DSP parameters
Pedal1 On Rate, Pedal1 Off Rate, Pedal2 On Rate, Pedal2 Off Rate: on value,
on rate, off value, off rate for each pedal*
Arp Hold On/Off: Arpeggio hold setting*
Song Str/Stp: Song sequencer playback start/stop*
Phrase Str/Stop: Phrase playback start/stop*
Audio Str/Stop: Audio playback start/stop*
*1 For details about each setting, see the MIDI Implementation Chart
(http://world.casio.com/) and/or MIDI documentation.
*2 After selecting these setting items, press the
and then adjust the items below.
MSB: 63H for NRPN, 65H for RPN (Setting range: 000 to 127)
LSB: 62H for NRPN, 64H for RPN (Setting range: 000 to 127)
Send Data: Specifies whether knob operation controls MSB or LSB
value. (Settings: MSB, LSB)
*3 This setting is not supported for Damper/Pedal 1 (Pedal 1) or Pedal 2.
*4 This setting is supported for Damper/Pedal 1 (Pedal 1) and Pedal 2 only.
Minimum value. Controller minimum output value setting.
Maximum value. Controller maximum output value setting.
Knob 2 to 4 (Knob 2 to 4 edit). This is a group of
editable parameters. Editing can be performed even when the "Knob 2-4
Enable" setting is "Off". Details of editable parameters are the same as
"Knob1 Edit >Ent", above.
Description
ct
(TEMPO) button.
3 (K1) knob editable parameters.
1
*
1 2
1
3
4
4
4
4
em (ENTER) button again
3 Knob (K2) through (K4)
Settings
20 - 255
U000 - U999
Off, On, Hold
0 - 7
dk (ZONE)
Refer to the cell to the
left.
0 - 127
0 - 127