Chauvet Q-Wash User Manual
419z-led
Hide thumbs
Also See for Q-Wash:
- User manual (16 pages) ,
- Specifications (1 page) ,
- Supplementary manual (1 page)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Chauvet Q-Wash
Summary of Contents for Chauvet Q-Wash
- Page 1 User Manual...
- Page 2 Copyright Notice CHAUVET® owns the content of this user manual in its entirety, including but not limited to pictures, logos, trademarks, and resources. © Copyright 2013 CHAUVET®. All rights reserved.
-
Page 3: Table Of Contents
Fan Control ....................................13 Pan/Tilt Speed.................................... 13 Reverse Pan Direction ................................13 Reverse Tilt Direction ................................. 13 Optics Speed....................................13 Reverse Dimmer Direction ................................. 13 Head Motion Black Out ................................13 Color Settings..................................... 14 Dimmer Curves ..................................14 Q-Wash™ 419Z-LED User Manual... - Page 4 Reset to Factory Default ................................16 Software Version ..................................16 Menu Map ................................... 17 DMX Values ................................22 5. Technical Information ..........................29 Product Maintenance ..............................29 Returns ..................................29 Technical Specifications ............................. 30 Contact Us .................................. 31 -ii- Q-Wash™ 419Z-LED User Manual...
-
Page 5: Before You Begin
Failure to report damage to the carrier immediately may invalidate your claim. In addition, keep the box and contents for inspection. For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with CHAUVET® within 7 days of delivery. Convention Meaning... -
Page 6: Safety Notes
· The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate this product at a higher temperature. · In case of a serious operating problem, stop using this product immediately! In the unlikely event that your CHAUVET® product may require service, contact CHAUVET® Technical Support. Expected LED LEDs gradually decline in brightness over time, mostly because of heat. -
Page 7: Introduction
2. Introduction Description The Q-Wash™ 419Z-LED is a high-power quad-color RGBW LED, moving head wash product. This product consists of a base section and a moving yoke with a pan range of up to 540º. The moving head, which has a tilt range of 270º, contains the 19 quad-color RGBW LEDs and the zoom motors. -
Page 8: Overview
Introduction Overview Control Panel Handles Omega Brackets Side View Front View Quad-Color LEDs Power Switch Fuse Power In/Out Top View Rear View Data In/Out Q-Wash™ 419Z-LED User Manual... -
Page 9: Dimensions
Introduction Dimensions 13.43 in 14.49 in 341 mm 368 mm 11.69 in 10.63 in 297 mm 270 mm 3.86 in 98 mm 8.86 in 225 mm 13.31 in 338 mm Q-Wash™ 419Z-LED User Manual... -
Page 10: Setup
The Q-Wash™ 419Z-LED has an auto-ranging power supply that works with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the power requirements for each Q-Wash™ 419Z-LED, refer to the label affixed to the product. You can also refer to Technical Specifications section in this manual. -
Page 11: Dmx Linking
Setup DMX Linking You can link the Q-Wash™ 419Z-LED to a DMX controller using a standard DMX serial connection. If using other DMX compatible products with the Q-Wash™ 419Z-LED, you can control each individually with a single DMX controller. The Q-Wash™ 419Z-LED uses the standard DMX data connection for its PERSON1, DMX Modes PERSON2, PERSON3, PERSON4, and PERSON5 DMX modes. -
Page 12: Mounting
· When hanging this product, always secure to a fastening device using a safety cable (included). Procedure The Q-Wash™ 419Z-LED comes with two omega brackets to which you can attach clamps. You must supply your own clamps and make sure that they are capable of supporting the weight of this product. -
Page 13: Operation
DOWN the numeric value when in a function Control Options You can set the Q-Wash™ 419Z-LED starting address in the 001 to 512 DMX range. This enables control of up to 15 products in the 34-channel PERSON5 personality. Programming Refer to the Menu Map to understand the menu options. -
Page 14: Control Panel Lock
Go to ADDRESS main level. b. Select the starting address (001~512). The highest recommended starting address for each DMX mode are as follows: DMX Mode DMX Address DMX Mode DMX Address PERSON1 PERSON4 PERSON2 PERSON5 PERSON3 -10- Q-Wash™ 419Z-LED User Manual... -
Page 15: Loss Of Signal Setting
Programs 1. Go to STAND ALONE > RUN. 2. Select the desired auto (AUTO1, AUTO2), test (TEST), or custom program (CUSTOM). You cannot edit any of the auto or test programs (AUTO1, AUTO2, or TEST). Q-Wash™ 419Z-LED User Manual -11-... -
Page 16: Edit Custom Programs
4. Select USE. a. Select YES to save the program or NO to discard. Master/Slave The Master/Slave mode allows a group of Q-Wash™ 419Z-LEDs (slave products) to simultaneously duplicate the output of another Q-Wash™ 419Z-LED (master product) without a DMX controller. -
Page 17: Fixture Cloning
Operation The Q-Wash™ 419Z-LED gives you 3 ways in which to transfer the settings from 1 Q- Fixture Cloning Wash™ 419Z-LED to other Q-Wash™ 419Z-LED products when hooked up via DMX daisy chain configuration. To transfer the CUSTOM program only: 1. -
Page 18: Color Settings
For optimum control of the 16-bit dimming channels in the PERSON2 and PERSON5 personalities, be sure that both dimming curves in SETTINGS > PERFORM > DIMMER and SETTINGS > PERFORM > CURV are set to OFF -14- Q-Wash™ 419Z-LED User Manual... -
Page 19: Zoom Position Adjust
The values of RED, GREEN, and BLUE configured from SERVICE > CALIB.C > RGBTOW will define the color temperature shown when the RGB faders are set to “255” if SETTINGS > PERFORM > COLOR > RGBtoW is active. Q-Wash™ 419Z-LED User Manual -15-... -
Page 20: Product Reset Control
Select DMX to reset the product from a DMX controller or DISPLAY to reset the product from the control panel only. The Q-Wash™ 419Z-LED gives you 3 different levels to reset the product. Reset To reset the Pan and Tilt motors only: 1. -
Page 21: Menu Map
Activates the move-in black delay BLACKOUT (3 sec) INSTANT DIM4 DIM3 Slow (DIM4) to fast (DIM1) dimmer curves DIMMER DIM2 DIM1 Linear dimmer/no dimmer function CURV3 Slow (CURV3) to fast (CURV1) dimmer CURV2 curves CURV CURV1 No dimmer Q-Wash™ 419Z-LED User Manual -17-... - Page 22 DISPLAY LOCK Activates/deactivates the main level password **** DEFAULT Resets fixture to factory default settings (Enter Password) Sends ALL settings of the 1st product to all SEND other Q-Wash™ 419Z-LEDs connected to the DMX output -18- Q-Wash™ 419Z-LED User Manual...
- Page 23 Select the zoom position TIME Selects the step duration Activates the changes Sends CUSTOM settings of the 1st product to SEND all other Q-Wash™ 419Z-LEDs connected to the DMX output INFO SOFTWARE V.X.X Shows version of software installed ALL RESET...
- Page 24 SERVICE BLUE WHITE CALIB.C 000~255 GREEN 4900K Sets color temperature for White 4 BLUE WHITE GREEN 5600K Sets color temperature for White 5 BLUE WHITE GREEN Sets color temperature for White 6 5900K BLUE WHITE -20- Q-Wash™ 419Z-LED User Manual...
- Page 25 DISPLAY2 ********* CONTENT Sends CONTENT settings of the 1st product SEND to all other Q-Wash™ 419Z-LEDs connected to the DMX output **** Service Recovery Resets all custom modes to default values (Enter Password) Q-Wash™ 419Z-LED User Manual...
-
Page 26: Dmx Values
DIM0 (3 s activation delay) 240 ó 243 DIM1 (3 s activation delay) 244 ó 247 DIM2 (3 s activation delay) 248 ó 251 DIM3 (3 s activation delay) 252 ó 255 DIM4 (3 s activation delay) -22- Q-Wash™ 419Z-LED User Manual... - Page 27 221 ó 225 White 5 226 ó 230 White 6 231 ó 235 White 7 236 ó 240 White 8 241 ó 245 White 9 246 ó 250 White 10 251 ó 255 White 11 Q-Wash™ 419Z-LED User Manual -23-...
- Page 28 DIM0 (3 s activation delay) 240 ó 243 DIM1 (3 s activation delay) 244 ó 247 DIM2 (3 s activation delay) 248 ó 251 DIM3 (3 s activation delay) 252 ó 255 DIM4 (3 s activation delay) -24- Q-Wash™ 419Z-LED User Manual...
- Page 29 DIM0 (3 s activation delay) 240 ó 243 DIM1 (3 s activation delay) 244 ó 247 DIM2 (3 s activation delay) 248 ó 251 DIM3 (3 s activation delay) 252 ó 255 DIM4 (3 s activation delay) Q-Wash™ 419Z-LED User Manual -25-...
- Page 30 000 ó 255 Blue 2 0~100% 000 ó 255 White 2 0~100% 000 ó 255 Red 3 0~100% 000 ó 255 Green 3 0~100% 000 ó 255 Blue 3 0~100% 000 ó 255 White 3 0~100% -26- Q-Wash™ 419Z-LED User Manual...
- Page 31 Green 1 0~100% 000 ó 255 Green 1 Fine 0~100% 000 ó 255 Blue 1 0~100% 000 ó 255 Blue 1 Fine 0~100% 000 ó 255 White 1 0~100% 000 ó 255 White 1 Fine 0~100% Q-Wash™ 419Z-LED User Manual -27-...
- Page 32 Green 3 0~100% 000 ó 255 Green 3 Fine 0~100% 000 ó 255 Blue 3 0~100% 000 ó 255 Blue 3 Fine 0~100% 000 ó 255 White 3 0~100% 000 ó 255 White 3 Fine 0~100% -28- Q-Wash™ 419Z-LED User Manual...
-
Page 33: Technical Information
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be the customer’s responsibility. FedEx packing or double-boxing are recommended. CHAUVET® reserves the right to use its own discretion to repair or replace returned product(s). Q-Wash™ 419Z-LED User Manual... -
Page 34: Technical Specifications
Thermal Max. External Temperature Cooling System 104 °F (40 °C) Fan-Assisted Convection I/O Connectors Connector Type Channel Range 3- and 5-pin XLR Sockets 8,10,21,21,34 Ordering Product Name Item Code UPC Number Q-Wash™ 419Z-LED 01010722 781462210700 -30- Q-Wash™ 419Z-LED User Manual... -
Page 35: Contact Us
Technical Information World Headquarters United Kingdom and Ireland Contact Us CHAUVET® CHAUVET® Europe Ltd. General Information General Information Address: 5200 NW 108th Avenue Address: Unit 1C Sunrise, FL 33351 Brookhill Road Industrial Estate Voice: (954) 577-4455 Pinxton, Nottingham, UK Fax:...