Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Quick Reference Manual
Advertisement
Table of Contents
Related Manuals for Chauvet Xeno 2500
Summary of Contents for Chauvet Xeno 2500
- Page 1 User Manual...
- Page 2 Copyright Notice CHAUVET® owns the content of this user manual in its entirety, including but not limited to pictures, logos, trademarks, and resources. © Copyright 2013 CHAUVET®. All rights reserved.
-
Page 3: Table Of Contents
Table of Contents Table of Contents 1. Before You Begin ............................1 What Is Included ................................1 Claims ....................................1 Manual Conventions ................................1 Symbols ....................................1 Product at a Glance ..............................2 Safety Notes ................................2 Personal Safety ..................................2 Mounting and Rigging ................................2 Power and Wiring ................................... - Page 4 Table of Contents Notes Xeno™ 2500 User Manual Rev. 1...
-
Page 5: Before You Begin
Failure to report damage to the carrier immediately may invalidate your claim. In addition, keep the box and contents for inspection. For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with CHAUVET® within 7 days of delivery. Manual Conventions Convention... -
Page 6: Product At A Glance
• CAUTION: Flashing light is known to trigger epileptic seizures. User must comply with local laws regarding notification of strobe use. In the unlikely event that your CHAUVET® product may require service, contact CHAUVET® Technical Support. Xeno™ 2500 User Manual Rev. 1... -
Page 7: Introduction
Introduction 2. Introduction The Xeno™ 2500 is an ultra-high frequency strobe luminaire powered by a 2,500-watt Xenon Product lamp. When multiple products are linked, built-in automated programs trigger several Description pre-programmed shows via master/slave. The product is controlled by sound-activation or DMX through 3- and 5-pin connectors. -
Page 8: Product Overview
Introduction Overview Scroller Safety 3- and 5 pin-DMX Control Attachment Cable Loop In/Out Panel Yoke Bracket Slave Out Front View Rear View Breaker Power Microphone Sensitivity Knob Top View Bottom View Yoke Adjustment Knob Side View Xeno™ 2500 User Manual Rev. 1... -
Page 9: Product Dimensions
Introduction Dimensions Xeno™ 2500 User Manual Rev. 1... -
Page 10: Setup
The listed current rating indicates the maximum current draw during normal operation. For more information, download Sizing Circuit Breakers from the CHAUVET® website: www.chauvetpro.com. Always connect this product to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire. -
Page 11: Dmx Linking
Lamp Replacement The Xeno™ 2500 is equipped with a 2,500-watt Xenon lamp. Replacement lamps may be ordered from CHAUVET®. Follow the procedure below to safely change the Xeno™ 2500 lamp. Disconnect the product from the AC power before opening. DO NOT change lamp while product is plugged into power! Serious personal injury can occur. -
Page 12: Increasing The Lamp's Life
Setup 4. Side B contains 2 wires (1- white and 1 clear) that are connected to a terminal block. Unscrew these wires and carefully note where each was connected. CAUTION: Do not misalign or reverse the connections when installing the new lamp! 5. -
Page 13: Scroller Mounting Bracket
Setup The Xeno™ 2500 is includes an adaptor bracket to mount a scroller. Follow the Scroller Mounting procedure below to mount the scroller brackets. Bracket Procedure 1. Turn the product off and disconnect it from power. Wait at least 15 minutes for the lamp to cool down. -
Page 14: Mounting
Always mount this product in a safe position and make sure there is adequate room for ventilation, configuration, and maintenance. Rigging CHAUVET® recommends using the following general guidelines when mounting this product. • When selecting an installation location, consider easy access to this product for operation, programming adjustments, and routine maintenance. -
Page 15: Operation
Operation 4. Operation Control Panel Button Function Description Sets the currently selected value into the selected function <MENU> or exits from the current menu or function. Press and hold for 3 seconds to turn display backlight off Navigates upward through the menu list and increases the <UP>... -
Page 16: Master/Slave Mode
Operation Master/Slave Mode This mode allows you to set the MASTER product to control other products daisy chained together. There are 3 ways to configure Master/Slave mode. 1. Go to FL. (00~99) in the main level on the first MASTER product. Standalone Flash Master/Slave Mode 2. -
Page 17: Dmx Values
Operation DMX Values 3 CH Channel Function Value Percent/Setting 000 009 Sound-Active mode 010 099 Single flash mode Mode Selection 100 199 Quad flash mode 200 249 Blinder effect 250 255 Blinder effect with fade out 000 ... -
Page 18: Dmx Values (Cont.)
Operation DMX Values (cont.) 4 CH Channel Function Value Percent/Setting 000 009 Sound-Active mode 010 099 Single flash mode Mode Selection 100 199 Quad flash mode 200 249 Blinder effect 250 255 Blinder effect with fade out 000 ... -
Page 19: Technical Information
Be prepared to provide the model number, serial number, and a brief description of the cause(s) for the return. The user must clearly label the package with an RMA number. CHAUVET® will refuse any product returned without an RMA number. -
Page 20: Technical Specifications
Technical Specifications 6. Technical Specifications Dimensions and Length Width Height Weight Weight 18.35 in (466 mm) 4.41 in (112 mm) 10.87 in (276 mm) 8.4 lbs (3.81 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Electrical Power Supply Type Range Voltage Selection Switching (internal) -
Page 21: Contact Us
User Manual Contact Us World Headquarters United Kingdom and Ireland CHAUVET® CHAUVET® Europe Ltd. General Information General Information Address: 5200 NW 108th Avenue Address: Unit 1C Sunrise, FL 33351 Brookhill Road Industrial Estate Voice: (954) 929-1115 Pinxton, Nottingham, UK Fax:...