Integra DTR-40.3 Instruction Manual page 62

Operating on the AV receiver
1
Press Tone repeatedly to select either "Bass" or
"Treble".
2
Use + and – to adjust.
Note
• To bypass the bass and treble tone circuits, select the Direct or
THX listening mode.
• This setting is not available when the multichannel Analog input
is selected.
Speaker Levels
■
Subwoofer Level
–15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■
Center Level
–12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to standby. To save the setting you made
here, go to "Level Calibration"
setting the AV receiver to standby.
Note
• You cannot use this function while the AV receiver is muted.
• Speakers that are set to "No" or "None" in "Speaker
Configuration" (➔ page 47) cannot be adjusted.
Dolby Volume
■
Dolby Volume
See "Dolby Volume" of "Audio Adjust"
Note
• This setting cannot be used in either of the following cases:
– Direct listening mode is selected.
– the multichannel analog input is selected.
– any of the THX listening modes is selected, with "Loudness
Plus" set to "On" or "Preserve THX Settings" set to "Yes"
page 49).
(➔
• When "Dolby Volume" is set to "On", the "Dynamic EQ" and
"Dynamic Volume" settings of all input selectors are switched
to "Off".
En
62
(➔ page 48) before
page 51).
(➔
Audyssey
■
Audyssey
See "Audyssey" in "Source Setup"
■
Dynamic EQ
See "Dynamic EQ" in "Source Setup"
■
Dynamic Volume
See "Dynamic Volume" in "Source Setup"
Note
• These technologies can be used when all the following
conditions are met:
– Room Correction and Speaker Setup is completed. Note that
"Audyssey" requires the "Audyssey MultEQ XT Full
Calibration" method.
– Any listening mode other than Direct is selected.
– A pair of headphones is not connected.
– multichannel analog input is not selected.
• The setting is stored individually for each input selector.
• "Dynamic EQ" and "Dynamic Volume" cannot be selected
when any of the THX listening modes is selected, with
"Loudness Plus" set to "On" or "Preserve THX Settings" set
to "Yes".
• When "Dynamic EQ" is set to "On" or "Dynamic Volume" is
set to anything else than "Off", "Dolby Volume" will be
switched to "Off".
Late Night
■
Late Night
For Dolby Digital and Dolby Digital Plus sources, the
options are:
Off
Low:
Small reduction in dynamic range.
High:
Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
Auto:
The Late Night function is set to "On" or "Off"
automatically.
Off
On
Turn this setting on to reduce the dynamic range of Dolby
Digital material so that you can still hear quiet parts even
when listening at low volume levels—ideal for watching
movies late at night when you don't want to disturb
anyone.
Note
• The effect of the Late Night function depends on the material
that you are playing and the intention of the original sound
designer, and with some material there will be little or no effect
when you select the different options.
• The Late Night function can be used only when the input source
is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.
• The Late Night function is set to "Off" when the AV receiver is
set to standby. For Dolby TrueHD sources, it will be set to
"Auto".
(➔ page 52).
page 52).
(➔
(➔ page 52).