Advertisement

SCENIC
GRAND SCENIC
DRIVER'S HANDBOOK

Advertisement

   Summary of Contents for Renault GRAND SCENIC

  • Page 1

    SCENIC GRAND SCENIC DRIVER’S HANDBOOK...

  • Page 2

    RENAULT vehicles. ELF lubricants are a major factor in your vehicle’s performance. RENAULT recommends the approved ELF lubricants for your oil changes and top-ups. Contact your RENAULT representative or visit the site: www.lubricants.elf.com The oil born in Formula One...

  • Page 3: Driving

    Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle. Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from RENAULT, 92 100 Billancourt 2009.

  • Page 5: Table Of Contents

    Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........

  • Page 7: Table Of Contents

    Section 1: Getting to know your vehicle RENAULT cards: general information, use, deadlocking ....... . .

  • Page 8: Battery Life

    (refer to the information for a short while. by the word “SERVICE” engraved on on the “RENAULT card: battery” in sec- They may pose a risk to themselves the card. Refer to the information on tion 5).

  • Page 9

    Replacement: need for an Using the key additional RENAULT card Refer to the information on “Locking/ If you lose your RENAULT card or unlocking the doors”. require another, you can obtain one Once you have accessed the vehicle from an approved dealer.

  • Page 10: Luggage Compartment

    If a door or the luggage compartment is open RENAULT card not detected or not properly shut, or if a RENAULT alarm card is still in the reader, the doors and If a door is opened when the engine...

  • Page 11: Unlocking The Vehicle

    With the RENAULT card in zone 1, the functions of the remote control place your hand on a door handle 2: the RENAULT card, it can be used to lock/ vehicle will unlock (in some cases, you unlock without using the RENAULT may need to pull door handle 2 twice to card, when it is in access zone 1.

  • Page 12: Locking The Vehicle

    The vehicle will lock. If a door or the tailgate is open or not properly closed, the vehicle will quickly lock/ unlock. Note: a RENAULT card must be within the vehicle's access zone (zone 1) to be able to lock the vehicle using the button.

  • Page 13

    After locking/unlocking the vehicle or the tailgate only using the but- tons on the RENAULT card, remote locking and unlocking in hands-free mode are deactivated. To reactivate the hands-free mode: restart the vehicle.

  • Page 14

    RENAULT cARd: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. The hazard warning lights flash once to indicate that the doors have been un- locked. To activate deadlocking If the vehicle is equipped with a dead-...

  • Page 15

    RENAULT “sERVIcE” cARd deactivation of the “sERVIcE” mode There are two possibilities: – press a button on the RENAULT card (not the RENAULT “SERVICE” card); – start the engine with a RENAULT card (not the RENAULT “SERVICE” card). With the card in reader 2, press button 1.

  • Page 16: Doors

    Pull on the handle 2. With the doors unlocked or the After switching off the engine, the lights RENAULT “hands-free” card in your and any accessories that are in opera- Lights-on reminder buzzer possession, hold handle 1 and pull it to- tion (radio, etc.) will continue to oper-...

  • Page 17: Child Safety

    Note: if there is a system fault, the mes- Never leave your vehicle with the RENAULT card inside and never leave sage “Check child safety device” is dis- a child (or a pet) unsupervised, even for a short while.

  • Page 18

    LOckINg/UNLOckINg ThE dOORs (1/2) Locking/Unlocking the doors from the outside This is done using the RENAULT Card; see the “RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc.

  • Page 19

    Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle's access zone or using the Interior locking/unlocking key integrated in the RENAULT card.

  • Page 20: Automatic Locking When Driving

    AUTOmATIc LOckINg WhEN dRIVINg Activating/deactivating the Operating faults function If you experience an operating fault (no automatic locking, the indicator light in- To activate: with the vehicle stopped corporated in button 1 does not light up and the ignition on, press switch 1 until when trying to lock the doors and tail- a beep sounds.

  • Page 21: Front Headrests

    fRONT hEAdREsTs To remove the headrest Fit it in its highest position, press button 1 on each rod 3 and lift to re- lease. Note: when the headrest is removed, take care not to change the positions of rods 3. To refit the headrest If the setting of rods 3 has been altered, pull them fully upwards.

  • Page 22

    fRONT sEATs WITh mANUAL cONTROL (1/2) To move the seat forwards or To tilt the seatback back Turn control knob 3 to the required po- sition. Lift handle 1 to release. Release the For safety reasons, make handle at the desired position and make these adjustments only sure that it is locked.

  • Page 23: Heated Seats

    fRONT sEATs WITh mANUAL cONTROL (2/2) Table function heated seats When the front seat is in (depending on vehicle) table position, the front pas- Depending on the vehicle, the passen- senger air bag must be dis- ger seatback may be folded down onto With the engine running, turn control 6 abled (see information on the seat base to create a table.

  • Page 24: Adjusting The Lumbar Support

    dRIVER’s sEAT WITh ELEcTRIc cONTROLs Switch 4 is used for adjusting the seat base and switch 3 is used for adjusting the seatback. On equipped vehicles, buttons 2 store the chosen driving posi- tion (refer to the following page). Adjusting the seat position To move the seat forwards or back Move switch 4 forwards or backwards.

  • Page 25

    When driving, it is not possible to recall – with the “hands-free” card de- a driving position. tected or, depending on the vehicle, RENAULT card in the card reader; – when the driver’s door is opened. storing your driving position – Adjust the seat using switches 4 and 5 (see previous page);...

  • Page 26: Seat Belts

    sEAT BELTs (1/3) Before starting, first adjust your driv- Always wear your seat belt when trav- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belt to ensure op- ticular country you are in.

  • Page 27

    sEAT BELTs (2/3) ç driver’s seat belt reminder and, depending on the vehi- cle, front passenger seat belt re- minder This lights up on the instrument panel when the engine is started, then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and...

  • Page 28

    sEAT BELTs (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. – For special operations (e.g.: fitting child seats) contact an approved Dealer. –...

  • Page 29: Rear Seat Belts

    REAR sEAT BELTs second row centre rear seat Unwind belt 2 slowly from its housing. On equipped vehicles, for your com- fort, you can pass the belt through belt guide 3. Click buckle 4 into black catch 5. Snap last sliding buckle 6 into the red catch 7.

  • Page 30: To The Front Seat Belts

    mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...

  • Page 31: Methods Of Restraint In Addition To The Front Seat Belts

    mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (2/4) Load limiter Air bags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is indi- an acceptable level.

  • Page 32

    mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (3/4) Operation special feature of the front air This system is only operational when the ignition is switched on. After a violent impact, it has two deploy- ment volumes and integrates a ventila- In a severe frontal impact, the air bags tion system: inflate rapidly, cushioning the impact...

  • Page 33

    mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...

  • Page 34: To The Rear Seat Belts

    mEThOds Of REsTRAINT IN AddITION TO ThE REAR sEAT BELTs force limiter Depending on the vehicle and the posi- – Have the entire restraint tion of the seats, these may comprise: Above a certain severity of impact, this system checked following –...

  • Page 35: Side Protection Devices

    sIdE pROTEcTION dEVIcEs side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows...

  • Page 36: Additional Methods Of Restraint

    AddITIONAL mEThOds Of REsTRAINT All of the warnings below are given so that the air bag is not obstructed in any Operating faults way when it is inflated and also to prevent the risk of serious injuries caused å by items which may be dislodged when the air bag inflates. This warning light comes on when the engine is started and then The air bag is designed to complement the action of the seat belt.

  • Page 37: Child Safety: General Information

    chILd sAfETy: general information carrying children Using a child seat Set a good example by always fas- The level of protection offered by the Children, and adults, must be correctly tening your seat belt and teaching child seat depends on its ability to re- seated and strapped in for all journeys.

  • Page 38

    chILd sAfETy: choosing a child seat Rear-facing child seats forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need From 15 kg or 4 years, the child can than that of an adult and its neck is very to be protected as a priority.

  • Page 39: Choosing A Child Seat Mounting

    chILd sAfETy: choosing a child seat mounting (1/2) Attachment using the ISOFIX There are two ways of attaching child Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised ISOFIX child seats are ap- chased for another vehicle, proved in accordance with regulation check that its installation is...

  • Page 40

    chILd sAfETy: choosing a child seat mounting (2/2) The rings are located on the floor and indicated by markings on the luggage compartment carpet. To access these anchoring points, push the rear seat forward and lift the cover if necessary. Note: for 7-seater vehicles, the rings are located on the luggage compart- ment floor and are visible.

  • Page 41: Fitting A Child Seat

    chILd sAfETy: fitting a child seat (1/9) In the front seat Some seats are not suitable for fitting child seats. The diagram on the follow- The laws concerning children travel- ing page shows you how to attach a ling in the front passenger seat differ in child seat.

  • Page 42

    chILd sAfETy: fitting a child seat (2/9) In the rear seat In the rear centre seat A carrycot can be installed across the Some child seats are too wide to allow vehicle and will take up at least two access to the seat belt buckles. Check seats.

  • Page 43

    chILd sAfETy: child seat installation diagram (3/9) child seat attached using the IsOfIX 5-seater normal chassis version mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.

  • Page 44

    chILd sAfETy: fitting a child seat (4/9) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. seat size Weight of front passenger Rear side Rear centre Type of child seat the child seat (1) (5)

  • Page 45

    chILd sAfETy: child seat installation diagram (5/9) 5-seater long chassis version child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.

  • Page 46

    chILd sAfETy: fitting a child seat (6/9) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. seat size Weight of front passenger Rear side Rear centre Type of child seat the child seat (1) (5)

  • Page 47

    chILd sAfETy: child seat installation diagram (7/9) 7-seater version child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.

  • Page 48

    chILd sAfETy: fitting a child seat (8/9) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. front seat size Weight of Row 2 rear Row 2 rear Row 3 rear Type of child seat passenger...

  • Page 49

    chILd sAfETy: fitting a child seat (9/9) X = Seat not suitable for fitting child seats. U = Seat allowing a child seat with “Universal” approval to be attached by seat belt; check that it can be fitted correctly. IUf/IL = On equipped vehicles, seat which allows a child seat with “Universal/Semi-universal or vehicle specific” approval to be fitted using the ISOFIX system;...

  • Page 50: Deactivating/activating The Front Passenger Air Bag

    chILd sAfETy: deactivating/activating the front passenger air bag (1/2) The front passenger air bag must only be deactivated or activated when the vehicle is stationary. If it is interfered with when the vehicle is being driven, indicator å © lights will come Switch the ignition off then on again to reset the air bag in accordance...

  • Page 51: Operating Faults

    chILd sAfETy: deactivating/activating the front passenger air bag (2/2) Operating faults It is not permitted to fit a rear-facing child seat to the front passenger seat if the air bag activation/deactivation system is faulty. It is not recommended to allow any other passenger to sit in that seat if the ›...

  • Page 52

    dRIVINg pOsITION: LEfT-hANd dRIVE (1/2) 1 2 3 5 6 7 8 10 11 1.46...

  • Page 53

    3 Stalk for: switch. 19 Gear lever. – direction indicator lights; 11 Location for radio, navigation system, 20 RENAULT card reader. – exterior lights; etc. 21 Cruise control/speed limiter control. – front fog lights; 12 – Display of the time, tempera- 22 Heating and ventilation controls.

  • Page 54

    dRIVINg pOsITION: RIghT-hANd dRIVE (1/2) 14 15 1.48...

  • Page 55

    12 Location for driver’s air bag and information, navigation system in- 21 Electronic parking brake control. horn. formation, etc. 22 RENAULT card reader. 13 – Steering column stalk for wind- – Driver and front passenger seat screen and rear screen wash/ 23 Gear lever.

  • Page 56: Steering Wheel, Power-assisted Steering

    sTEERINg WhEEL/pOWER-AssIsTEd sTEERINg power-assisted steering Operating faults The steering may become stiff when Variable power-assisted steering driving or when the steering wheel is The variable power-assisted steering turned repeatedly. This is due to the system is equipped with an electronic power assistance overheating.

  • Page 57

    INsTRUmENT pANEL: warning lights (1/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. Φ speed limiter and cruise control indicator lights See the information on the “Speed lim- iter” and “Cruise control” in Section 2. ®...

  • Page 58

    INsTRUmENT pANEL: warning lights (2/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. Ä Toxic fume filter system Warning Light This lights up when the ignition is switched on and goes out when the engine is started.

  • Page 59

    INsTRUmENT pANEL: warning lights (3/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. ç å driver’s seat belt reminder Rear seat belt reminder (depending Air bag warning light and, depending on the vehi- on vehicle) This lights up when the engine ç...

  • Page 60

    INsTRUmENT pANEL: warning lights (4/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. It requires you to stop immediately, for your own safety, as soon as traf- fic conditions allow. switch off the engine and do not restart it. Contact an approved Dealer.

  • Page 61

    INsTRUmENT pANEL: warning lights (5/5) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. À The following warning lights come Oil pressure warning light ® on accompanied by the warn- This lights up when the ignition ing light.

  • Page 62

    INsTRUmENT pANEL: display and indicators (1/4) Rev counter (rpm × 1,000) This is displayed according to how the instrument panel is customised. speedometer (km/h or mph) fuel gauge The remaining fuel level is shown in yellow. If the level is at the minimum, the warning light integrated in the indicator comes on, accompanied by a beep.

  • Page 63

    INsTRUmENT pANEL: display and indicators (2/4) Instrument panel in miles Overspeed buzzer (option to switch to km/h) Depending on the vehicle and coun- – With the ignition off, press button 3 try, a buzzer sounds for approximately or 4 and start button 5; 10 seconds every 40 seconds, as long as the vehicle is travelling in excess of –...

  • Page 64: Instrument Panel

    INsTRUmENT pANEL: display and indicators (3/4) Vehicle without “TfT display” fuel level gauge 6 Overspeed buzzer instrument panel Depending on the vehicle and coun- If the level is at the minimum, the try, a buzzer sounds for approximately warning light integrated in the indicator Instrument panel B 10 seconds every 40 seconds, as long comes on, accompanied by a beep.

  • Page 65

    INsTRUmENT pANEL: display and indicators (4/4) Instrument panel in miles Engine oil level low warning (option to switch to km/h) When the engine is started, the instru- – With the ignition off, press button 3 ment panel display alerts you when the or 4 and start button 5.

  • Page 66: Trip Computer And Warning System

    TRIp cOmpUTER ANd WARNINg sysTEm (1/9) c) mileage before service; d) tyre pressure monitor; e) cruise control/speed limiter pro- grammed speed (only for vehicles which are not equipped with a “TFT Display” instrument panel); f) on-board log, operating fault and in- formation message readout.

  • Page 67

    TRIp cOmpUTER ANd WARNINg sysTEm (2/9) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption and average speed will become more stable and reliable the further you have travelled since the last...

  • Page 68

    TRIp cOmpUTER ANd WARNINg sysTEm (3/9) The display of information shown below dEpENds ON ThE VEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. b) Journey parameters. fuel used. Fuel consumed since the last reset. Average fuel consumption since the last reset.

  • Page 69

    TRIp cOmpUTER ANd WARNINg sysTEm (4/9) The display of information shown below dEpENds ON ThE VEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected current fuel consumption. This value is displayed above a speed of approximately 18 mph (30 km/h). Estimated range with remaining fuel.

  • Page 70

    TRIp cOmpUTER ANd WARNINg sysTEm (5/9) The display of information shown below dEpENds ON ThE VEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected c) mileage before service. Distance remaining until the next service (displayed in miles (kilometres) and months), then when the service nears, several scenarios are possible: –...

  • Page 71

    TRIp cOmpUTER ANd WARNINg sysTEm (6/9) Journey parameters The display of information shown below dEpENds ON ThE VEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected d) Tyre pressure monitor. Refer to the information on the “Tyre pressure monitor” in Section 2. e) cruise control/speed limiter programmed speed (only for vehicles which are not equipped with a “TfT display”...

  • Page 72: Information Messages

    “parking brake on” Indicates that the parking brake has been applied. “please remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle. “checking control Displayed with the ignition on when the vehicle is running self-diagnostics.

  • Page 73

    TRIp cOmpUTER ANd WARNINg sysTEm (8/9) Operating fault messages © These appear with the warning light and mean that you should drive very carefully to an approved dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.

  • Page 74: Warning Messages

    TRIp cOmpUTER ANd WARNINg sysTEm (9/9) Warning messages ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. stop your engine and do not restart it. contact an approved dealer. Examples of warning messages are given in the following pages.

  • Page 75: Vehicle Settings Customisation Menu

    VEhIcLE sETTINgs cUsTOmIsATION mENU Adjusting the settings Once the function has been selected, activate or deactivate it using button 2: Depending on the vehicle equipment, press button 3 or 4 to select the func- function activated tion to be modified: <...

  • Page 76: Clock And Exterior Temperature

    cLOck ANd EXTERIOR TEmpERATURE External temperature indicator special note: When the outside temperature is –3°C to +3°C, the °c characters flash (signal- ling a risk of black ice on the road). If the electrical supply is cut (battery disconnected, broken supply wire, etc.), the clock will lose its time set- Resetting the clock 1 Vehicles fitted with control 3...

  • Page 77: Door Mirrors

    REAR VIEW mIRRORs folding door mirrors The door mirrors automatically fold in when the vehicle is locked (switch 2 in position D). In this case, they will fold out when the ignition is next switched In any case, you can make the door mirrors fold in (switch 2 in position E) or out (switch 2 in position C).

  • Page 78: Audible And Visual Signals

    AUdIBLE ANd VIsUAL sIgNALs direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0.

  • Page 79: Exterior Lighting And Signals

    EXTERIOR LIghTINg ANd sIgNALs (1/3) á main beam headlights With the dipped beam head- lights lit, pull stalk 1 towards you. This indicator light on the instrument panel comes on. To return to the dipped headlight posi- tion, pull stalk 1 towards you again. daytime running lights function Depending on the vehicle, the day-...

  • Page 80: Switching Off The Lights

    EXTERIOR LIghTINg ANd sIgNALs (2/3) special features Note: if the fog lights are lit, the lights are not switched off automatically. – For vehicles equipped with auto- matic lighting, if the dipped beam headlights are manually switched on “see-me-home lighting” and the light is sufficient, the direc- function tional headlights will remain fixed;...

  • Page 81: Rear Fog Light

    EXTERIOR LIghTINg ANd sIgNALs (3/3) front fog lights switching off the lights Turn centre ring 5 on stalk 1 Turn ring 5 again until mark 4 is oppo- until the symbol faces mark 4, then re- site the symbol for the fog light that you lease it.

  • Page 82

    ELEcTRIcAL AdJUsTmENT Of ThE dIppEd BEAm hEAdLIghTs for manual settings Examples of positions for adjusting control A according to the load driver alone or with front passenger driver with one front passenger and one rear passenger On vehicles fitted with this function, con- trol A allows you to adjust the height of the beams according to the load.

  • Page 83: Windscreen Wipers

    WINdscREEN WIpER, WAshER ( Vehicle fitted with front windscreen wiper rain sensor A park B automatic wiper function When this position is selected, the system detects water on the wind- screen and triggers the wipers at a suitable wiping speed. It is possi- ble to change the triggering thresh- old and the time sweeps by turning ring 2:...

  • Page 84: Headlight Washers, Windscreen Washer

    WINdscREEN WIpER, WAshER ( headlight washers headlights on On equipped vehicles, hold stalk 1 Do not try to lift the wiper blades. pulled towards you for about 1 second, They cannot remain detached from and the headlight washers and wind- the windscreen.

  • Page 85: Rear Screen Wash/wipe

    REAR scREEN WAsh/WIpE Activating/deactivating the rear screen wiper (depending on the vehi- cle) If your vehicle is fitted with a vehicle settings customisation menu, it is pro- grammed to activate the rear wipers when reverse gear is selected (if the windscreen wipers are on).

  • Page 86: Fuel Grade

    fUEL TANk (1/2) fuel grade Vehicles running on ethanol- based fuel Use a high-grade fuel that complies with the legislation in force in each It is essential to use unleaded petrol or country and which must conform to the fuel containing a maximum of 85% eth- specifications given on the label on the anol (E85).

  • Page 87

    fUEL TANk (2/2) filling with fuel persistent smell of Insert the nozzle to open valve A and fuel insert it fully before turning it on to fill If you notice a persistent the fuel tank (risk of splashing). smell of fuel you should: Keep the nozzle in this position through- –...

  • Page 88

    1.82...

  • Page 89

    Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting - stopping the engine .

  • Page 90

    RUNNING IN Petrol version Diesel version Up to 600 miles (1,000 km), do not For the first 900 miles (1,500 km), do exceed 78 mph (130 km/h) in top gear not exceed 2,500 rpm. After complet- or 3,000 to 3,500 rpm. ing this mileage you may drive faster, however, it is only after approximately You may only expect top performance...

  • Page 91: Starting The Vehicle

    + START” warns of this. Remote control RENAULT RENAULT “hands-free” card card The RENAULT card must be inserted in “Hands-free” starting with card reader 2 or in detection zone 3. When you get into the vehicle, insert the the tailgate open RENAULT card fully into card reader 2.

  • Page 92: Starting The Engine

    In certain cases, the RENAULT “hands- RENAULT card, insert the card into free” card may not work: reader 2; – when the RENAULT card battery is – vehicles with a RENAULT “hands- drained, flat battery, etc. free” card, with the card in the pas- –...

  • Page 93: Stopping The Engine

    If the card is no longer in the reader cle, especially if you have when you try to switch the engine off, your RENAULT card with the message “No keycard Press and you, check that the engine hold” appears on the instrument panel: is completely switched off.

  • Page 94: Special Features Of Petrol Versions

    SPECIAL fEATURES Of PETROL vERSIONS The following operating conditions If you notice any of the above operating should be avoided: faults, have the necessary repairs car- ried out as soon as possible by an ap- – driving for long periods when the low proved dealer.

  • Page 95: Running Out Of Fuel

    SPECIAL fEATURES Of DIESEL vERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.

  • Page 96: Selecting Reverse Gear

    GEAR LEvER/HANDbRAkE Handbrake To release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. To apply: Pull the lever 2 upwards and make sure the vehicle is immobilised. Make sure that the hand- Selecting reverse gear brake is properly released when driving (red indicator...

  • Page 97: Electronic Parking Brake

    ELECTRONIC PARkING bRAkE (1/3) Note: To indicate that the electronic parking brake is applied or released, a beep sounds and the message “Apply park- ing brake” appears on the instrument panel: – with the engine running: when the driver’s door is opened; –...

  • Page 98: Manual Operation

    3 at the same time; You can control the electronic parking To manually activate the electronic park- – remove the RENAULT card from the brake manually. ing brake, (when stopping at a red light, card reader. or stopping when the engine is running, Applying the electronic parking etc.): pull and release switch 3.

  • Page 99

    ELECTRONIC PARkING bRAkE (3/3) versions with an automatic Operating faults – If there is an electronic parking brake ® fault, warning light lights up gearbox © – If there is a fault, the warning accompanied by the “Parking brake light illuminates on the instrument For safety reasons, automatic release fault”...

  • Page 100: Engine Adjustments

    ADvICE: antipollution, fuel economy and driving (1/3) Aiding fuel economy By virtue of its design, moderate fuel Have your vehicle adjusted and checked consumption and initial settings, your by an approved Dealer, in accordance Depending on the vehicle, in order to vehicle conforms to current antipol- with the instructions given in your main- optimise consumption, an indicator light...

  • Page 101

    ADvICE: antipollution, fuel economy and driving (2/3) Ä This warning light on the in- – Brake as little as possible. If you an- strument panel will indicate if ticipate an obstacle or bend in ad- there are any faults in the system: vance, you may then simply release This lights up when the ignition is the accelerator pedal.

  • Page 102

    ADvICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.

  • Page 103

    ENvIRONMENT Recycling Make your contribution towards Your vehicle has been designed with respect for the environment in mind for protection of the environment too. Your vehicle is 85% recyclable and its entire service life: during production, – Worn parts replaced in the course of 95% recoverable, in line with European use and at the end of its life.

  • Page 104: Operating Principle, Tyre Pressure Monitor, Changing A Wheel

    TyRE PRESSURE MONITOR (1/4) The tyre pressures must be adjusted If the vehicle is equipped with the func- tion, this system monitors the tyre pres- when cold (refer to the label located on sure. the edge of the driver’s door). If tyre pressures cannot be checked when the tyres are cold, the recom- Operating principle...

  • Page 105

    TyRE PRESSURE MONITOR (2/4) “Tyre pressure sensors absent” or “Check tyre pressure sensors” One wheel B disappears, indicating that the sensor on this wheel is missing or faulty (e.g. if the emergency spare wheel is fitted). vehicles without “TfT “Inflate tyres for motorway” The tyre pressure is not suitable for the display”...

  • Page 106: Vehicles With Tft Display

    TyRE PRESSURE MONITOR (3/4) “Inflate tyres for motorway” The wheel concerned E is shown in orange on display 4. The tyre pressure is not suitable for the speed of travel. Slow down or inflate all four tyres to mo- torway pressure (refer to the informa- tion on “Tyre pressures”...

  • Page 107

    TyRE PRESSURE MONITOR (4/4) Replacing wheels/tyres Tyre repair product and This system requires specific equip- inflation kit ment (wheels, tyres, hubcaps, etc.). Because the valves are specially de- Contact an approved Dealer to fit new signed, only use equipment approved tyres and to find out about available ac- by the approved network.

  • Page 108: Driver Correction Devices/aids

    DRIvER CORRECTION DEvICES AND AIDS (1/3) AbS (anti-lock braking Operating faults: Depending on the vehicle, this is com- posed of: system) © – the (anti-lock braking – lit up on the in- Under heavy braking, the ABS prevents system); strument panel along with the mes- the wheels from locking, allowing the –...

  • Page 109: Electronic Stability Program

    DRIvER CORRECTION DEvICES AND AIDS (2/3) Electronic stability program Understeer control Operating faults ESP with understeer control This system optimises the action of the When the system detects an operating and traction control ASR l’ESP in the case of pronounced under- fault the message “Check ESP”...

  • Page 110: Emergency Brake Assist

    DRIvER CORRECTION DEvICES AND AIDS (3/3) Hazard warning lights switching on The traction control ASR offers addi- tional safety, it is recommended that Depending on the vehicle, these may you do not drive with the function disa- light up in the event of sudden decel- bled.

  • Page 111

    CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. Controls Switching on  Press switch 5 on the side showing 1 Limit speed activation, storage and ...

  • Page 112

    CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Driving Exceeding the limit speed When a limited speed has been stored It is possible to exceed the limit speed and this speed is not reached, driving is at any moment. To do this: press the similar to driving a vehicle without the accelerator pedal firmly and fully speed limiter function.

  • Page 113

    CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Switching off the function The speed limiter function is deacti- vated if you press switch 5: in this case a speed is no longer stored. The orange  indicator light on instrument panel A goes out to confirm that the function is deactivated.

  • Page 114

    CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). This function is an addi- tional driving aid.

  • Page 115

    CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Driving Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelera- tor pedal. Switching on Activating cruise control Press switch 5 on the side showing At a steady speed (above 20 mph ...

  • Page 116

    CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed Putting the function on standby The cruising speed may be exceeded at any time by depressing the accelera- The function is suspended when you: tor pedal. – press switch 3 (O); The cruising speed flashes on the in- –...

  • Page 117

    CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Switching off the function The cruise control function is deacti- vated if you press switch 5: in this case a speed is no longer stored. The green  indicator light on the instrument panel A goes out to confirm that the function is deactivated.

  • Page 118

    PARkING DISTANCE CONTROL (1/3) Operating principle Ultrasonic detectors, installed in the front or rear bumper depending on the vehicle, measure the distance between the vehicle and an obstacle whilst re- versing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centi-...

  • Page 119: Parking Distance Control

    PARkING DISTANCE CONTROL (2/3) front parking distance control (depending on vehicle) Operation The parking distance control system is only activated when the vehicle is driven at a speed below approximately 6 mph (10 km/h). Most objects located less than approx- imately 60 centimetres away from the front of the vehicle are detected and a beep is emitted.

  • Page 120: Special Features

    PARkING DISTANCE CONTROL (3/3) Operating faults You can also adjust the volume. From the vehicle settings customisation When the system detects an operating menu (refer to the information on the fault , a beep sounds for approximately “Vehicle settings customisation menu” 3 seconds each time reverse gear is se- in Section 1), select the line “Parking lected and is accompanied by the mes-...

  • Page 121: Reversing Camera

    REvERSING CAMERA fixed clearance gauge 2 This gauge remains fixed and indicates The fixed clearance gauge comprises the vehicle trajectory if the wheels are coloured markers A, B and C indicating in line with the vehicle. the distance behind the vehicle: This system is initially used with the aid –...

  • Page 122: Selector Lever

    AUTOMATIC GEARbOx (1/3) Operation Driving in automatic mode With the gear lever 1 in position P, Select position D. In most traffic con- switch on the ignition. ditions, you will not have to touch the gear selector lever again: the gears will With the foot on the brake pedal (warn- change automatically at the right time ing light...

  • Page 123: Parking The Vehicle

    AUTOMATIC GEARbOx (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, – if the road contours and bends do When the vehicle is stopped, move the move the lever to the left. Shifting the not allow you to stay in automatic lever to position P while keeping your lever repeatedly allows you to change...

  • Page 124

    AUTOMATIC GEARbOx (3/3) Operating faults – when driving, if the message “Check auto gearbox” appears on the instru- ment panel, this indicates there is a fault. Contact your approved Dealer as soon as possible; – when driving, if the message “Auto gearbox overheating”...

  • Page 125: Your Comfort

    Section 3: Your comfort Air vents............... Manual air conditioning .

  • Page 126

    AIR VENTS (air outlets) (1/2) 1 left-hand side air vent 2 left-hand side window demister outlet 7 rear air vents 3 windscreen demister outlets 8 passenger footwell heater outlets 4 centre air vents 9 automatic climate control/manual air 5 right-hand side window demister conditioning control panel.

  • Page 127: Front Seats, Rear Seats

    AIR VENTS (2/2) Front seats Rear seats To remove bad odours from your ve- hicles, only use the systems designed Move tab 3 to the right or left to direct Air flow for this purpose. Consult an approved the air flow. Dealer.

  • Page 128: Passenger Compartment

    MANuAl AIR coNDITIoNINg (1/2) Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed be- tween all the air vents, the front side window demisting vents, the...

  • Page 129: Adjusting The Ventilation Speed

    MANuAl AIR coNDITIoNINg (2/2) Adjusting the ventilation speed Turn control 2 clockwise to increase the air flow in the passenger compartment. Passenger compartment ventilation is referred to as “blown air”. The ven- tilation fan determines the air flow. However, it is also affected by the ve- hicle speed.

  • Page 130: Automatic Climate Control, Automatic Mode

    AuToMATIc clIMATE coNTRol (1/5) Automatic mode The automatic climate control system ensures, in most cases, a comfortable temperature in the passenger compart- ment, while maintaining good visibility and optimising fuel consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condition- ing and air temperature.

  • Page 131

    AuToMATIc clIMATE coNTRol (2/5) clear View function Press button 10: the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de- icing functions must be activated.

  • Page 132

    AuToMATIc clIMATE coNTRol (3/5) The displayed temperature values show a comfort level. When starting the engine, increasing or decreasing the value displayed will not allow the comfort level to be reached any more quickly. The system will always optimise the tem- perature increase or decrease (the ventilation system does not start in- stantly at maximum speed: it gradu-...

  • Page 133

    AuToMATIc clIMATE coNTRol (4/5) The air flow is directed to the windscreen and the front side window demisting vents. × The air flow is distributed be- tween all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells.

  • Page 134

    AuToMATIc clIMATE coNTRol (5/5) Recycling This function is controlled automatically, but it can also be activated manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; –...

  • Page 135: Maintenance, Air Conditioning: Information And Advice On Use

    AIR coNDITIoNINg: information and advice on use Advice on use In some situations (air conditioning operating faults off, air recirculation activated, ven- Fuel consumption tilation speed at zero or low, etc.), As a general rule, contact your ap- You will normally notice an increase you may notice that condensation proved Dealer in the event of an op- in fuel consumption (especially...

  • Page 136: Electric Windows

    Never leave your vehicle with the Electric windows From the driver’s seat, use switch: Renault card inside and never 1 for the driver’s side; Press or pull the switch to raise or lower leave a child (or a pet) unsuper- 2 for the front passenger’s side;...

  • Page 137: Sun Blind, Special Note

    A B c When you lock the doors from the out- side, press the locking button on the RENAulT card twice in quick suc- cession, or on the driver's door in hands-free mode, and all the windows will close automatically.

  • Page 138: Precautions During Use

    Never leave your vehicle with the If the roof does not close, turn button 7 recommended. RENAULT card inside and never to the 0 position, then press button 8 leave a child (or a pet) unsuper- Before using the sunroof, check the until the roof is fully closed: consult an vised, even for a short while.

  • Page 139: Courtesy Light

    MANuAl wINDow wINDERS/INTERIoR lIghTINg (1/2) Manual window winders courtesy light Front door lights Turn handle 1. Tilt switch 3 to move it to the position On equipped vehicles, light 5 comes on for: when the door is opened. – permanent lighting; –...

  • Page 140

    INTERIoR lIghTINg (2/2) glove box light 6 luggage compartment light 7 Light 6 comes on when the cover is Depending on the vehicle, light 7 comes opened. on when the luggage compartment is opened. 3.16...

  • Page 141: Vanity Mirror

    SuN BlIND/MIRRoRS Front sun visor Vanity mirror child minder mirror Lower the sun visor 1 over the wind- Slide cover 3. Pull on recess 4 to open it. screen or unclip it and lower it over the Depending on the vehicle, light 2 is au- side window.

  • Page 142: Sun Visor

    SuN VISoR lateral sun visor Rear side sun blind Rear sun blind on the tailgate Pull the sun blind upwards using tab 1 Pull the sun blind upwards using hook 3 Pull the sun blind upwards using tabs 6 until hook 2 engages in its housing until it engages in housing 4 (make sure until they engage in hook 5 (make sure (make sure that the hook is correctly...

  • Page 143

    PASSENgER coMPARTMENT SToRAgE/FITTINgS (1/6) Door pockets 1 Dashboard storage Storage compartment under compartment 2 the instrument panel 3 It can hold a 1.5 litre bottle. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus Ensure that no hard, heavy or pointed objects are placed in the “open”...

  • Page 144

    PASSENgER coMPARTMENT SToRAgE/FITTINgS (2/6) Sunglasses holder 4 Sun blind storage 5 central storage compartment or control 6 This can be used for storing motorway tickets, cards, etc. Depending on the vehicle, central con- trol 6 may be replaced by a storage compartment.

  • Page 145: Armrest Storage

    PASSENgER coMPARTMENT SToRAgE/FITTINgS (3/6) central elbow rest 8 central storage Armrest storage compartment C compartment D The central elbow rest slides to allow the length to be adjusted. Slide it Raise armrest 8. With the armrest in the retracted posi- (movement A).

  • Page 146

    PASSENgER coMPARTMENT SToRAgE/FITTINgS (4/6) Passenger storage cup holder 11 compartment It can hold a can, a cup or the ashtray. Pull handle 10 to open it. The glove box can hold A4-size docu- ments, a large bottle of water, etc. The storage compartment is ventilated and refrigerated.

  • Page 147

    PASSENgER coMPARTMENT SToRAgE/FITTINgS (5/6) Rear door storage Front seat storage clothes hooks 14 compartment 12 compartments 13 grab handle 15 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.

  • Page 148

    PASSENgER coMPARTMENT SToRAgE/FITTINgS (6/6) Retaining hook 16 Storage drawer 17 under Front and rear underfloor front and rear seats storage areas 18 This is used to hold bags while the ve- hicle is moving. These drawers can hold a road atlas, These compartments can hold road the vehicle documentation, etc.

  • Page 149: Cigar Lighter

    AShTRAY/cIgAR lIghTER/AccESSoRIES SockET cigar lighter 1 Accessories sockets With the ignition on, push in cigar You may use cigar lighter recess 1 or lighter 1; it will spring back with a click one of the sockets 3 (depending on the when it is ready.

  • Page 150: Rear Headrests

    REAR hEADRESTS Position for use To adjust side supports A Lift the headrest to maximum height, Depending on the vehicle, sections A then lower it until it locks. can be adjusted independently to the desired position. To remove the headrest Storage position B Press the tab(s) 1, then remove the headrest.

  • Page 151

    chIlD’S coNVERTIBlE hEADREST Removing a headrest Press tab 4 and release the headrest. Fitting a headrest Insert the headrest rods in the holes. Pull the headrest towards you and slide it to the desired height at the same time. For the child setting, lift lock 2 to re- lease strap 3.

  • Page 152: Adjusting The Rear Seats

    ADJuSTINg ThE REAR SEATS To fold down a seatback (table posi- tion) Lower headrest 3. Lift handle 4 or, depending on the vehi- cle, pull tab 1. An occasional table position can be cre- ated by folding the seatback all the way down onto the seat cushion.

  • Page 153

    REAR SEAT FuNcTIoNS (1/2) Folding up a seat Returning a seat to its normal Note: it may be necessary to move the passenger and/or driver’s seats position Lower the headrest. forwards and to lower the seatback in Lower the seat until it locks in place at order to tilt the seat as far forwards as Seat with control 2 floor level (movement A).

  • Page 154

    REAR SEAT FuNcTIoNS (2/2) When fitting side seats, make sure that the seat belt buckle is inside the vehicle. For safety reasons, carry out any adjustments when the vehicle is stationary. To remove a seat To fit a seat Attach the hooks 8 to rail 9 marked 10 With the seat folded down, gently lower by gently lifting the back of the seat.

  • Page 155

    REAR SEAT oPERATIoN: 7-seater version (1/2) Third row rear seats To unfold a seat When moving third row rear – From the luggage compartment, seats: Folding up a seat remove the luggage cover and store – check that no one is near –...

  • Page 156

    REAR SEAT oPERATIoN: 7-seater version (2/2) Accessing the third row rear use restriction – pull the second row rear seat to put it into the table position; seats It is not permitted to drive with a second – lift the seatback. row rear seatback or seat folded down –...

  • Page 157: Inside The Vehicle

    TAIlgATE To open opening manually from inside the vehicle Press button 1 and lift the tailgate. Special note To close If it is impossible to unlock the tailgate, Lower the tailgate using the handles 2 it can be done manually from inside: inside the tailgate to help you.

  • Page 158: Rear Parcel Shelf: Normal Chassis Versions

    REAR PARcEl ShElF: normal chassis versions Rear parcel shelf To remove, unhook the two straps 1. Fold section A onto section B, then pull up and towards you. To refit it, proceed in reverse order to removal. Do not place any objects, especially heavy or hard objects, on the parcel shelf.

  • Page 159

    luggAgE coVER: long chassis versions To remove the flexible Removing the luggage cover luggage compartment cover section of the luggage cover storage Push the luggage cover to the right (movement A) and lift the left-hand side Using handle 1, pull it gently to release Housing 2 in the luggage compartment of the inertia reel (movement B).

  • Page 160: Luggage Compartment Storage Space And Fittings

    luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS (1/2) Side storage compartments 1 Storage compartment under luggage compartment carpet Depending on the vehicle, this may be Depending on the vehicle, to access used to hold oil containers etc. this, lift the luggage compartment carpet.

  • Page 161

    luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS (1/2) Separating the luggage Anchorage points compartment Hooks 6 located on each corner of the (depending on the vehicle) luggage compartment, allow the load to be secured. The loading area can be separated. Lift divider 4. The elastic band 5 on the back is used to hold objects vertically.

  • Page 162

    TRANSPoRTINg oBJEcTS IN ThE luggAgE coMPARTMENT, TowINg (towing equipment) Always place the objects to be trans- ported so that their largest side rests against the back of the rear bench seat, for normal loads (example A) or against Always position the heavi- the back of the front seats B when the est items directly on the rear bench seatbacks are folded down.

  • Page 163

    luggAgE NET (1/2) Fitting the luggage net Depending on the vehicle, this may be – attach the two hooks 3 on the net used when transporting animals or lug- straps 4 to the anchoring points 5; behind the front seats gage to isolate them from the passen- –...

  • Page 164

    luggAgE NET (2/2) Fitting the luggage net – attach net strap hook 8 to the lower Depending on the vehicle, remove the ring; anchoring rings 11 before installing a behind the rear seats luggage net. (behind the second row rear seats on –...

  • Page 165: Roof Bars

    RooF BARS Access to the mounting points Open the doors to access the mount- For information on the range of ing points 1. equipment adapted to your vehi- cle, we advise you to consult an ap- proved Dealer. Refer to the fitting instructions for in- formation on how to fit roof bars and conditions of use.

  • Page 166: Multimedia Equipment

    MulTIMEDIA EquIPMENT Multimedia systems hands-free telephone The equipment described below may integrated control or may not be fitted to the vehicle, and On equipped vehicles, use steering its location may vary, depending on the column control 5 and microphone 6. vehicle navigation system version.

  • Page 167

    Section 4: Maintenance Bonnet ............... . Engine oil level/engine oil change .

  • Page 168: Opening The Bonnet

    Bonnet Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.

  • Page 169

    enGIne oIL LeVeL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- In order to prevent splashback, it is tween oil changes. recommended that a funnel be used when topping up/filling with oil However, contact your approved...

  • Page 170: Engine Oil Level: Topping Up/filling

    enGIne oIL LeVeL: topping up/filling (1/2) topping up/Filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...

  • Page 171: Oil Change

    enGIne oIL LeVeL: topping up/filling (2/2) Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels. Filling: take care when topping up the oil that no oil drips onto engine components - risk of fire.

  • Page 172

    LeVeLS (1/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Service (very severe damage is likely to be Booklet for your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...

  • Page 173: Brake Fluid Level

    LeVeLS (2/3) Level 1 topping up It is normal for the level to drop as the After any operation on the hydraulic cir- brake shoes become worn, but it must cuit, a specialist must replace the fluid. never drop lower than the “MInI” warn- Only use fluids approved by our ing line.

  • Page 174

    LeVeLS FILteRS (3/3)/ Liquid Filters Windscreen washer fluid. In winter, use The replacement of filter elements (air anti-freeze product. filter, passenger compartment filter, diesel filter, etc.) is scheduled in the Jets maintenance operations for your vehi- cle. Use a tool such as a needle to adjust the height of the windscreen washer Replacement intervals for filter el- jets.

  • Page 175: Tyre Pressure

    tyRe pReSSURe tyre safety and use of snow chains Refer to the information on “Tyres” in Section 5 for the servicing con- ditions and, depending on the ver- sion, the use of chains. Special note For vehicles used fully laden (maximum permissible all-up weight) and towing a trailer.

  • Page 176

    BAtteRy Depending on the vehicle, a system continuously checks the battery charge status. If this drops, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the in- strument panel for the duration of the charging time.

  • Page 177

    BoDyWoRk MAIntenAnCe (1/2) protection against the effects you should not: – Use solvents not approved by our Technical Department to remove of corrosive agents – Degrease or clean mechanical stains as this could damage the components (eg. engine Although your vehicle has been treated paintwork.

  • Page 178

    BoDyWoRk MAIntenAnCe (2/2) you should – Observe the vehicle stopping dis- – Before going through a roller type car tances when driving on gravelled wash, return the windscreen wiper – Wash your car frequently, with the surfaces to prevent paint damage. stalk to the Off position (refer to engine off, with cleaning prod- the information on the “Windscreen...

  • Page 179

    InteRIoR tRIM MAIntenAnCe – Seat belts you should not: Whatever type of stain is on the trim, use soapy water (if possible, warm These must be kept clean. You are strongly advised not to use water) containing: high-pressure or spray cleaning equip- Use products selected by our –...

  • Page 180

    4.14...

  • Page 181: Practical Advice

    RENAULT card: battery ........

  • Page 182

    Puncture In case of puncture Special note The Tyre Pressure Monitor function Depending on the vehicle, a tyre infla- does not check the emergency spare tion kit or emergency spare wheel is wheel (the wheel replaced by the emer- provided (refer to the following pages). gency spare wheel disappears from the instrument panel display).

  • Page 183: Tool Kit

    tOOLS/HuBcaP (1/2) Bolt guide 5 For tightening/loosening wheel bolts on vehicles fitted with alloy wheels towing hitch 6 Refer to the information on “Towing” in Section 5. Do not leave the tools un- secured inside the vehicle as they may come loose under braking.

  • Page 184

    tOOLS/HuBcaP (2/2) Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, Location of the wheel change Wheel trim check that all the tools are correctly tool kit clipped into the tool kit, then posi- Remove it using hubcap tool 4 by en- tion it correctly in its housing: risk of gaging the hook in the recess provided...

  • Page 185

    tYre PreSSure KIt (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.

  • Page 186

    tYre PreSSure KIt (2/3) – press switch 5 to inflate the tyre to the recommended pressure (check the label affixed to the edge of the driver’s door); – after a maximum of 7 minutes, stop inflating and read the pressure (on the pressure gauge 4);...

  • Page 187

    tYre PreSSure KIt (3/3) Precautions when using the – affix driving recommendation label 10 to the dashboard where it can easily be seen by the driver; The kit should not be operated for more – store the kit; than 15 consecutive minutes. –...

  • Page 188: Emergency Spare Wheel

    eMerGencY SPare WHeeL emergency spare wheel A emergency spare wheel B to refit emergency spare wheel B Stand the wheel up with the valve to- It is located under the vehicle. In the This is located in the luggage compart- wards you.

  • Page 189

    cHanGInG a WHeeL If necessary, remove the wheel trim. – turn the wheelbrace until the wheel lifts off the ground; – Unlock the wheel bolts using wheel wrench 3. Position it so as to be able – undo the bolts and take off the to push from above;...

  • Page 190

    tYreS (1/3) tyre and wheel safety When the tyre tread has been worn to the level of the wear indicators, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.

  • Page 191: Tyre Pressures

    tYreS (2/3) tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including which may be reached in hot weather the emergency spare wheel). The tyre For safety reasons, this op- or following a fast journey.

  • Page 192

    tYreS (3/3) use in winter chains In all cases, we would recommend that you contact an approved dealer For safety reasons, fitting snow who will be able to advise you on chains to the rear axle is strictly for- the choice of equipment which is bidden.

  • Page 193: Daytime Running Light

    HeaDLIGHtS: changing bulbs (1/2) Daytime running light (depending on the vehicle) Remove cover B, turn bulb holder 3 to release it then replace the bulb. Daytime running light bulb type: P21LL. Discharge bulb main beam headlights/dipped beam headlights Never open cover A Bulb type: D1S.

  • Page 194: Halogen Headlights

    HeaDLIGHtS: changing bulbs (2/2) Main beamA/dipped B cleaning the headlights refitting halogen headlights Carry out the operations in reverse Use a soft cloth. If this does not clean order. Ensure that the bulb is correctly it properly, moisten the cloth with soapy removal repositioned (pay attention to the direc- water then rinse off.

  • Page 195

    HeaDLIGHtS: front fog lights Front fog lights 1 The front bumper needs to be removed; consult an approved Dealer. Any operation on (or modi- fication to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment (harness, components and in partic- ular the alternator).

  • Page 196: Led Lighting

    rear LIGHtS: changing bulbs (1/4) LeD lighting Long chassis version From the outside, undo screw 2 using a flat-blade screwdriver or similar and The lights are equipped with an LED pull the light unit towards you. Direction indicator lights/brake and lighting system as soon as the side side lights Unclip the bulb holder a quarter of a...

  • Page 197

    rear LIGHtS: changing bulbs (2/4) normal chassis version Unclip the bulb holder by pressing on refitting the tabs 6. To refit, proceed in the reverse order, Direction indicator lights and brake Replace the bulb. taking care not to damage the wiring. lights note: do not remove seal 9.

  • Page 198

    rear LIGHtS: changing bulbs (3/4) rear fog light and reversing Side light From the outside of the vehicle, pull on the light unit to remove it then unscrew light From the luggage compartment, unclip bulb holder 11 a quarter of a turn. (depending on the vehicle) the cover.

  • Page 199

    rear LIGHtS anD SIDe LIGHtS: changing bulbs (4/4) High level brake light 13 number plate lights 14 Indicator lights 16 Consult an approved Dealer. Unclip light 14 by pressing tab 15. Unclip indicator light 16 using a flat- blade screwdriver or similar. Position Remove the light cover to gain access it to A to tilt the rear indicator light to- to the bulb.

  • Page 200: Interior Lighting: Changing Bulbs

    InterIOr LIGHtInG: changing bulbs (1/2) courtesy light Door lights Sliding central console light – Set the three switches to the central Unclip light 2 (using a flat-blade screw- Unclip bulb 3 from its support. position; driver or similar). Bulb type: W5W. –...

  • Page 201

    InterIOr LIGHtInG: changing bulbs (2/2) Luggage compartment lights Disconnect the light. Press tab 5 to release lens 7 and Unclip lights 4 using a flat-blade screw- access bulb 6. driver or similar. Bulb type: W5W. The bulbs are under pres- sure and can break when replaced.

  • Page 202: Fuse Box

    FuSeS (1/2) INCORRECT CORRECT Fuse box tweezers 1 If any electrical component does not Remove the fuse using tweezers 3, lo- work, check the condition of the fuses. cated at the back of cover A or B. Unclip cover A or B (depending on ve- To remove the fuse from the tweezers, Check the fuse in question hicle).

  • Page 203

    FuSeS (2/2) allocation of fuses 8 Interior rear-view mirror; Some accessories are protected by fuses located in the engine compart- (the presence of certain fuses depends 9 Rear screen wiper; ment in fuse box C. on the vehicle equipment level) 10 and 11 Rear electric windows;...

  • Page 204: Connecting A Battery Charger

    BatterY: troubleshooting (1/2) to avoid all risk of sparks: connecting a battery charger – Ensure that any consumers (cour- the battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.

  • Page 205

    BatterY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.

  • Page 206: Replacing The Battery

    (insert the seal if it is not fully clipped on), then replace the RENAULT card battery, RENAULT card in the card reader) and press one of the card buttons, whilst in press button 1 pulling on emergency lock/unlock the vehicle (refer to the in- the vicinity of the vehicle;...

  • Page 207

    FIttInG a raDIO If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please con- –...

  • Page 208

    acceSSOrIeS Before fitting an electrical or electronic device (particu- No work may be carried out on the larly for transmitters/receiv- vehicle’s electrical or radio circuits, ers: frequency bandwidth, except by approved Dealers: an in- power level, position of the aerial correctly connected system may etc.), ensure that it is compatible result in damage being caused to...

  • Page 209: Windscreen Wiper Blades

    WIPer BLaDeS: replacing Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...

  • Page 210: Automatic Gearbox

    If your vehicle is the towing vehicle, do or r for vehicles with automatic trans- not exceed the maximum towing weight missions), insert the RENAULT card in for your vehicle (refer to the information the card reader then press the engine on “Weights”...

  • Page 211: Towing: Breakdown

    These towing points may only be used tool (or the key integrated with the for towing: never use them for lifting the RENAULT card) under the cover. vehicle directly or indirectly. Screw in towing hitch 7 fully: as much as possible by hand at first, then finish by tightening it using the wheelbrace.

  • Page 212

    Dealer as soon as possible. using the renauLt card POSSIBLe cauSeS WHat tO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the information on “Locking/unlocking the...

  • Page 213

    Starting conditions are not Refer to the information on “Starting/stopping the fulfilled. engine” in Section 2. The RENAULT “hands-free” Insert the card in the card reader in order to start card does not work. the engine. Refer to the information on “Starting/stopping the engine”...

  • Page 214

    OPeratInG FauLtS (3/5) On the road POSSIBLe cauSeS WHat tO DO Vibrations. Tyres not inflated to correct pressures, Check the tyre pressures: if this is not the incorrectly balanced or damaged. problem, have them checked by an ap- proved Dealer. Abnormal white smoke from the ex- Mechanical fault: cylinder head gasket Stop the engine.

  • Page 215

    OPeratInG FauLtS (4/5) On the road POSSIBLe cauSeS WHat tO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.

  • Page 216

    OPeratInG FauLtS (5/5) electrical equipment POSSIBLe cauSeS WHat tO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.

  • Page 217: Technical Specifications

    Section 6: Technical specifications Vehicle identification plates ............Dimensions .

  • Page 218: Vehicle Identification Plates

    Vehicle identification plates (1/3) the information shown on the ve- 6 Technical specifications of vehicle. hicle identification plate should be 7 Vehicle paint reference. quoted on all correspondence or 8 Equipment level. orders. 9 Vehicle type. 10 Trim code. Vehicle identification plate A 11 Additional equipment specifica- 1 Vehicle type and chassis number.

  • Page 219

    engine identification plates (2/3) the information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.

  • Page 220

    engine identification plates (3/3) the information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.

  • Page 221

    dimensions (in metres) normal chassis versions 0,888 2,702 0,753 1,546 4,343 1,624* 1,547 2,077 Unladen...

  • Page 222

    dimensions (in metres) (continued) long chassis versions 0,888 2,769 0,903 1,536 4,560 1,675* 1,539 2,077 Unladen...

  • Page 223: Engine Specifications

    engine specifications Versions 1.6 16V 1.4 tce 2.0 16V 1.5 dci 1.9 dci 2.0 dci engine type (see engine plate) cubic capacity (cc) 1.598 1.395 1.995 1.461 1.870 1.995 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.

  • Page 224

    Weights (in kg) the weights indicated are for a basic vehicle without options: they may vary depending on your vehicle’s equipment. consult an approved dealer. maximum permissible all-Up Weight (mmac) Weights are indicated on the vehicle identification plate (refer to gross train Weight (mtR) the information on “Vehicle identification plates”...

  • Page 225: Replacement Parts And Repairs

    If you always fit genuine RENAULT replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer's Network using original parts are guaranteed according to the conditions set out on the re-...

  • Page 226

    seRVice sheets (1/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...

  • Page 227

    seRVice sheets (2/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...

  • Page 228

    seRVice sheets (3/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...

  • Page 229

    seRVice sheets (4/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...

  • Page 230

    seRVice sheets (5/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...

  • Page 231

    seRVice sheets (6/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...

  • Page 232

    anticoRRosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.16...

  • Page 233

    anticoRRosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.17...

  • Page 234

    anticoRRosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.18...

  • Page 235

    anticoRRosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.19...

  • Page 236

    anticoRRosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.20...

  • Page 237

    anticoRRosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.21...

  • Page 238

    6.22...

  • Page 239: Alphabetical Index, Driver's Position, Control Instruments

    AlphABetiCAl inDex (1/5) central door locking ........1.8, 1.12 → 1.14 ABS ...............2.20 → 2.22 changing a bulb .............5.13 → 5.19 accessories................ 5.28 changing a wheel..............5.9 accessories socket ............3.25 changing gear ..........2.8, 2.34 → 2.36 additional methods of restraint .....1.24 → 1.27, 1.30 child headrest ..............

  • Page 240: Headlight Beam Adjustment

    AlphABetiCAl inDex (2/5) with manual controls ............ 1.16 electric beam height adjustment ........1.76 fuel electric windows ............3.12 → 3.14 advice on fuel economy ..........2.12 electronic parking brake ..........2.9 → 2.11 capacity ................ 1.80 Electronic Stability Program: ESP ......2.20 → 2.22 filling ..............

  • Page 241

    AlphABetiCAl inDex (3/5) brake lights ..............5.16 indicators ............1.72, 5.13 – 5.14 dipped beam headlights ......1.73, 5.13 – 5.14 indicators: direction indicators ..1.72, 5.13 – 5.14, 5.16, 5.18 – 5.19 direction indicators ..........1.72, 5.16 fog lights ..........1.75, 5.15 – 5.16 exterior temperature indicator ........

  • Page 242

    ............... 3.17 – 3.18 functions ..............3.28 sun visor ................3.17 rear view mirrors ..............1.71 sunroof..............3.12 → 3.14 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.14 switching on the vehicle ignition .......... 2.4 RENAULT card battery ................5.26 use ...............1.2 → 1.9 tailgate ..........

  • Page 243

    AlphABetiCAl inDex (5/5) transporting children ..........1.31 → 1.43 transporting objects in the luggage compartment ........3.38 luggage net ............3.39 – 3.40 trims ................5.3 – 5.4 trip computer and warning system... 1.51 → 1.55, 1.60 → 1.68 tyre inflation kit............5.5 → 5.7 tyre pressure..........2.16 →...

  • Page 245: For Your Safety

    4 SIMPLE ACTIONS* FOR YOUR SAFETY • Always fasten • Always secure children • Adjust the height of • Place heavy objects or your seat belt, using devices suitable the seat belt according luggage at the back of the – even for short journeys for their size and weight to your size.

  • Page 246

    à999109906Rí ï ë ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Comments to this Manuals

Symbols: 0
Latest comments: