To Change An Alarm Setting; To Stop A Tone/Vibration Alert Operation; To Test The Alarm; Stopwatch - Casio 3407 Operation Manual

Operation Guide 3407

To change an alarm setting

●
D to select the alarm whose setting you want to
1
In the Alarm Mode, use
change.
D
Alarm 1 Alarm 2
( ) (
D
Hourly Time Alarm 5
Signal ( ) (
D
E-30
The Alarm indicator is displayed while an alarm is turned on, while the Hourly
time signal indicator is displayed while the hourly time signal is turned on.
Alarm on
Alarm indicator
E-32
●
6
After all the settings are the way you want, press
screen.
●
7
To return to the Timekeeping Mode, press

To stop a tone/vibration alert operation

●
Double-tapping the center of the watch display or pressing any one of the
buttons will stop an ongoing tone/vibration alert operation.

To test the alarm

●
In the Alarm Mode, hold down D to perform the tone/vibration alert
operations.
E-34

To measure time with the stopwatch

●
The following shows button operations for stopwatch operations.
Elapsed time/cumulative time
D D
Start Stop (Restart)
Split time (paused elapsed time reading)
D B
Start Split Split time display
cancel
Pressing B while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-36

Timer

The timer start time can be set in one-minute increments up to 24 hours. The
watch will sound a tone or vibrate for about 10 seconds when the end of the timer
countdown is reached.
See "f. Alert method for alarm/timer" (page E-50).

To enter the Timer Mode

●
In the Timekeeping Mode, press C four times
Current time
to enter the Timer Mode.
See "Using Modes" (page E-14).
Hours Seconds
Minutes
E-38
D
Alarm 3
) ( )
D
Alarm 4
) ( )
D
Hourly time signal on
Hourly time signal indicator
A to exit the setting
C four times.
D D B
(Stop) Reset
B D B
Stop Reset
●
B to select the alarm type or to toggle the hourly time signal between
2
Use
on and off.
Alarm Types
: Alarm does not sound.
: Alarm sounds only once at the preset time and does not sound again after
that.
: Alarm sounds at the preset time each day.
Hourly time signal
: Hourly time signal does not sound.
: Hourly time signal sounds every hour on the hour.
●
3
To change an alarm time setting, hold down
the hour digits of the current alarm time start to fl ash.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hour digits will fl ash.
●
C causes the fl ashing to move between the hour and the
4
Each press of
minutes digits.
The fl ashing digits are the ones that are selected.
●
B and D to change the fl ashing setting, and set the hour and minutes
5
Use
you want.
Holding down either button scrolls the setting at high speed.
If you are using 12-hour timekeeping, the PM indicator will appear for times
between noon and 11:59 p.m.

Stopwatch

The stopwatch measures elapsed time in units of 1/100 seconds up to 23 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.

To enter the Stopwatch Mode

●
In the Timekeeping Mode, press C three
Current time
times to enter the Stopwatch Mode.
See "Using Modes" (page E-14).
[STW] will appear on the display for about
one second, and then the stopwatch screen
will appear.
Minutes 1/100 second
Hours Seconds
Note
Once started, elapsed time measurement continues until you press D to stop
it, even if you change to a different mode and even if the stopwatch reaches
the elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, split
time display will be canceled.

To set the timer start time

●
A for about two seconds.
1
In the Timer Mode, hold down
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hours digits will fl ash.
Note
If a timer countdown operation is in progress, press
D to stop it and then press B to reset the timer to
its start time before performing the above step.
If a timer countdown operation is paused, press B
to reset the timer to its start time before performing
the above step.
●
C causes the fl ashing to move between the hours and the
2
Each press of
minutes digits.
The fl ashing digits are the ones that are selected.
E-31
A for about two seconds until
E-33
E-35
E-37
E-39