Table of Contents
Advertisement
Operation Guide 5193
To stop the alarm
Press any button.
Note
Pressing any button while the alarm is sounding simply stops the alarm sound.
It does not stop the elapsed time operation that started when the end of the
countdown was reached. To stop the elapsed time operation, press B.
E-50
To view the time in another time zone
C to move the v Left Dial Hand to STD or DST.
1.
Use
The x Second Hand will move to the city code of the currently selected World
Time City.
D to move the x Second Hand to the city code you want to select as the
2.
Use
World Time City.
The n Right Dial Hands will move to the current time in the time zone of the
current city code. At this time, the z Hour Hand and c Minute Hand will
continue to indicate the current time in the Home City.
For full information on city codes, see the "City Code Table" at the back of this
manual.
If you think that the time indicated for the selected time zone is not correct, it
probably means that there is something wrong with your Home City settings. Use
the procedure under "To confi gure Home City settings" (page E-34) to correct
the Home City settings.
E-52
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
capability can come in handy when you frequently travel between two locations in
different time zones.
The following example shows what happens when the
Home City and World Time City are swapped while the
Home City originally is TOKYO (TYO) and the World Time
City is NEW YORK (NYC).
Before
swapping
After
swapping
E-54
The n Right Dial Hands will indicate the current time in your new World Time
City.
Note
If your current World Time City supports time calibration signal reception, making it
your Home City enables calibration signal reception for that city.
E-56
To change the alarm time setting
C to move the v Left Dial Hand to AL.
1.
Use
D (+) and B (–) to change the alarm time setting.
2.
Use
Each press of either button will move the n Right Dial Hands one minute.
Holding down D or B will start high-speed hand movement in the applicable
direction. To stop high-speed hand movement, press any button.
The alarm always works based on the time kept in the Timekeeping Mode.
The watch will return to the Timekeeping Mode automatically if you do not
perform any operation in the Alarm Mode for about two or three minutes.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm on and off. The x Second Hand will
indicate the current ON/OFF setting.
To stop the alarm
Press any button.
E-58
Home City
World Time City
TOKYO (TYO)
NEW YORK (NYC)
10:08 p.m.
9:08 a.m.
(Standard time)
(Daylight saving time)
NEW YORK (NYC)
TOKYO (TYO)
9:08 a.m.
10:08 p.m.
(Daylight saving time)
(Standard time)
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current time in one of 29 time zones
around the globe. The city that is currently selected in the World Time Mode is called
the "World Time City".
Hand Functions
x Second Hand:
Indicates the currently selected World Time City.
v Left Dial Hand:
Indicates the current STD (standard time) or DST
(daylight saving time) setting of the currently selected
time zone.
n Right Dial Hands:
Indicate the current time in the selected World Time
City in 24-hour format.
To specify standard time or daylight saving time (DST) for a city
1.
In the World Time Mode, use
whose setting you want to change.
Wait until the n Right Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
A for about two seconds until the watch
2.
Hold down
beeps. This will cause the v Left Dial Hand to toggle
between DST (daylight saving time) and STD (standard
Hold down
time).
A for two
Note that you cannot switch between STD (standard
seconds
time)/DST (daylight saving time) while UTC is
selected as the World Time City.
Note that the STD (standard time)/DST (daylight
saving time) setting affects only the currently selected
time zone. Other time zones are not affected.
To swap your Home City and World Time City
1.
In the World Time Mode, use
Time City you want.
In this example, you would move the x Second Hand
to NEW YORK (NYC) in order to select New York as
the World Time City.
Wait until the n Right Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
B for about three seconds until the watch beeps.
2.
Hold down
This will make the World Time City ( NEW YORK (NYC) in this example) your new
Home City. At the same time, it will change the Home City you had selected prior
to step 2 (TOKYO (TYO) in this example), to your World Time City.
After swapping the Home City and World Time City, the watch will stay in the
World Time Mode. The x Second Hand will point to your new World Time City
(TOKYO (TYO) in this example).
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day
when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
Hand Functions
x Second Hand:
Indicates the current alarm ON/OFF setting.
v Left Dial Hand: Points to AL.
n Right Dial Hands:
Indicate the current alarm time setting in 24-hour
format.
Adjusting Home Positions Manually
Strong magnetism or impact can cause the hands and/or date of the watch to be
off, even if the watch is able to perform the signal receive operation. If this happens,
perform the applicable home position adjustment procedures in this section.
Hand home position adjustment is not required if the time and day settings are
correct.
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing A. The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in home position adjustment mode. In either case, any
adjustments you made before the watch returned to the Timekeeping Mode will be
applied.
To adjust the home positions manually
C for about two seconds until the watch beeps twice and enters the
1.
Hold down
Timekeeping Mode.
E-51
D to select the city code
E-53
D to select the World
E-55
E-57
E-59
Advertisement
Table of Contents
