Related Manuals for Husqvarna R 322T AWD
Summary of Contents for Husqvarna R 322T AWD
- Page 1 Oper ator ′ s manual Rider 220T Rider 322T AWD Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.
-
Page 2: Table Of Contents
CONTENTS Contents Check the safety system ..........Replacing the light bulbs ..........CONTENTS Main fuse ..............Contents ..............Checking the tyre pressure .......... Ser vice journal Checking the engine’s cooling air intake ...... Pre-deliv ery service ............. Fitting the cutting head ..........After the first 8 hours ........... -
Page 3: Ser Vice Journal
Ser vice journal Pre-deliver y service 13 Tell customer about: Needs and benefits of following the service 1 Charge the battery for 4 hours at max. 3 amp. schedule. Servicing and the influence of this journal on the 2 Fit steering wheel, seat and any optional second-hand value of the machine. -
Page 4: Intr Oduction
Dear Customer , Thank y ou for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented articulated steering. Riders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine. - Page 5 SAFETY R ULES FOR USA Saf e operation practices f or ride-on • Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles. mo wer s Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope.
-
Page 6: Safety Rules For Usa
SAFETY RULES FOR USA IV. Service Safe handling of gasoline 1. Use extra care in handling gasoline and other fuels. They To avoid personal injury or property damage, use extrem care are flammable and vapours are explosive. in handling gasoline. Gasoline is extremely flammable the vapors are explosive a) Use only an approved container. -
Page 7: Travel And Transport On Public Roads
SAFETY RULES FOR USA Travel and transport on public roads Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held. Towing If your machine has a hydrostatic transmission you should only tow it very short distances at low speed if absolutely... -
Page 8: Key To Symbols
KEY TO SYMBOLS Symbols Clutch out These symbols are on the machine and in the instructions. Warning: rotating parts. Keep hands and feet clear. WARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual Rotary blades Keep hands and feet carefully and make sure you understand... - Page 9 KEY TO SYMBOLS Switch off the engine and take off the ignition cable before repairs or maintenance Check the engine’s oil level Check transmission oil level Lift up the cutting unit Apply the parking brake. If the engine is cold, use the choke Release the parking brake before driving The following labels are on the machine –...
-
Page 10: What Is What
WHAT IS WHAT? What is what on the ride-on mower 1 Speed limiter for driving forward 9 Cover lock 2 Speed limiter for reversing 10 Parking brake 3 Lifting lever for the cutting unit 11 Lock button for parking brake 4 Cutting height adjustment lever 12 Seat adjustment. -
Page 11: Safety Instructions
SAFETY INSTRUCTIONS Safety instructions • Stop the engine and prevent the engine from being started until you have cleaned the outlet channel. These instructions are for your safety. Read them carefully. • Look out for the ejector and do not direct it towards anyone. -
Page 12: Driving On Slopes
SAFETY INSTRUCTIONS This is what you do • Never allow children or other persons not trained in the use of the machine to use or service it. Local laws may • Remove obstacles such as stones, branches, etc. regulate the age of the user. •... -
Page 13: Children
SAFETY INSTRUCTIONS • Follow the manufacturer’s recommendations regarding • Petrol and petrol fumes are poisonous and extremely wheel weights or counterbalance weights to increase flammable. Be especially careful when handling petrol, as machine stability. carelessness can result in personal injury or fire. •... -
Page 14: Transport
SAFETY INSTRUCTIONS • Do not change the setting of governors. If you run too fast, Engage the parking brake and tie the tension belts around you risk damaging the machine components. See chapter stable parts on the machine, e.g. frame or rear wagon. on Technical data for highest permitted engine speed. -
Page 15: Presentation
PRESENTATION Presentation Speed limiter Congratulations on your choice of an excellent quality product The speed of the machine is steplessly regulated with two that will give you great pleasure for many years. This pedals. Pedal (1) is used to drive forwards, and pedal (2) to operator’s manual describes Rider 220T and drive backwards. -
Page 16: Lifting Lever For The Cutting Unit
PRESENTATION Lifting lever for the cutting unit Counter: 322T AWD The lift lever is used to set the cutting unit in transport or The chronometer shows how many hours the engine has mowing position. been running. Any time when the engine is not running but the ignition is switched on is not registered. -
Page 17: Release Lever
PRESENTATION Release lever Release lever Rider 220T The release control must be pulled out in order for the machine to be moved when the engine is shutoff. Should you attempt to drive the machine with the clutch controls pulled out it will not move. The drive on the axle is disengaged when one of the controls is pulled out. -
Page 18: Driving
Driving Before starting 4 If the engine is cold move the choke lever backwards to its end position. • Read the safety instructions and information concerning the placement of controls and functions before starting. • Perform daily maintenance before starting as set out in the Maintenance schedule. -
Page 19: Starting The Engine With A Weak Battery
Driving Starting the engine with a weak Driving the Rider battery 1 Release the parking brake by first pressing down the parking brake pedal and then releasing it. WARNING! Lead-acid batteries produce explosive gases. Avoid sparks, open flames and smoking close to batteries. Always wear protective glasses in the vicinity of batteries. -
Page 20: Cutting Tips
Driving Cutting tips Stop the engine Preferably allow the engine to idle for a minute to obtain normal working temperature before stopping it if it has been working hard. Avoid idling the engine for long periods, as there is a risk of carbon build-up on the spark plugs. 1 Lift up the cutting unit by pulling the lever backwards to its locked position. -
Page 21: Maintenance
Maintenance Maintenance schedule The following is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised service workshop. Daily maintenance At least once Maintenance Maintenance before starting a year interval in hours 100 200... -
Page 22: Cleaning
Maintenance Cleaning Front cover Release the clip on the front hood and lift off the fender. Clean the machine directly after use. It is much easier to wash off grass cuttings before they dry. Right-hand fender Remove the accelerator knob (1), screws (2 and 3), and Oily dirt can be removed using a cold degreasing agent. -
Page 23: Adjusting The Parking Brake Rider 220T
Maintenance Adjusting the parking brake Rider 2 Check the tension of the steering wires by squeezing them together by the arrows as illustrated. It should be 322T AWD possible to push them together so that the distance between them is half as much, without using unnecessary Check that the parking brake is adjusted correctly by placing force. -
Page 24: Checking And Adjusting The Choke Wire
Maintenance Checking and adjusting the choke Replacing the air filter wire WARNING! The exhaust system is hot. Let it If the engine is producing black smoke or is difficult to start cool before starting to replace the air filter. then the choke wire (upper wire) may be incorrectly adjusted. If doubts arise, contact your service representative. -
Page 25: Ignition System
Maintenance Check the safety system 8 Pull the filter over the air hose and clamp the filter cartridge in place with a hose clip. The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: •... -
Page 26: Replacing The Light Bulbs
Maintenance Replacing the light bulbs: 322T AWD 7 Refit the cables and screw the lamp holder on to the servo housing. For information about the bulb type, see Technical Data. 1 Unscrew the two screws holding the cover on the power servo housing. -
Page 27: Checking The Engine's Cooling Air Intake
Maintenance Checking the engine’s cooling air 3 Push the equipment frame down and place the catch against the frame. intake Clean the air intake grille in the engine cover behind the driver’s seat. 4 Engage the belt in the belt holder. Open the engine cover. -
Page 28: Removing The Cutting Unit
Maintenance 8 Fit the drive belt around the drive wheels of the cutting 4 Pull out the cutting unit. unit. Make sure the belt is placed on the correct side of the belt tensioner wheel. WARNING! Observe caution to avoid trapping your hand. -
Page 29: Checking The Cutting Unit's Parallelism
Maintenance Checking the cutting unit’s Replacing the cutting unit belts parallelism WARNING! Wear gloves to protect your Check the cutting unit’s parallelism as follows: hands when working with the blades. 1 Check the air pressure in the tyres 60 kPa/0.6 kp/cm /8.5 PSI. -
Page 30: Service Position For The Cutting Unit
Maintenance 7 Remove the screws on the cutting cover. Lift the unit 4 Disengage the spring for the drive belt tensioning wheel. frame and remove the cutting unit cover. 5 Loosen on the cutting height stay and place in the holder. 8 Loosen the spring that tensions the V-belt and pry off the belt. -
Page 31: Checking The Blades
Maintenance Restoring from service position Removing the BioClip plug 1 Grip the front edge of the unit and loosen the lock, fold To change a Combi unit from BioClip function to cutting unit down and slide in the unit. with rear ejection, remove the BioClip plug located under the unit with three screws. -
Page 32: Lubrication
Lubrication Checking the engine’s oil level. 1 Place a container underneath the engine’s left oil drain plug. Check the oil level in the engine when the Rider stands horizontal with the engine switched off. Open the engine cover. Loosen the dipstick, pull it up and wipe it off. 2 Remove the dipstick. -
Page 33: Checking The Transmission Oil Level
Lubrication Checking the transmission oil level General lubrication 1 Remove the transmission cover. Undo the two screws All joints and bearings are lubricated using molybdenum (one on each side) and lift off the transmission cover. disulphide grease during manufacture. Continue to lubricate using the same type of grease *. -
Page 34: Troubleshooting Schedule
Troubleshooting schedule Problem Procedure Engine does not start There is no fuel in the fuel tank Spark plug defective Faulty spark plug connections or interchanged cables Dirt in the carburettor or fuel line Starter motor does not turn over the engine Starter motor does not turn over the Battery flat engine... -
Page 35: Storage
Storage Winter storage Guard At the end of the season, or if the machine is going to stand There is a cover to protect your machine during storage or idle for more than 30 days, it should immediately be made transport. -
Page 36: T Echnical Data
Technical data Dimensions Rider 220T Rider 322T AWD Length without cutting unit, mm/ft 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 890/2,92 890/2,92 Height, mm/ft 1150/3,77 1150/3,77 Operating weight with cutting deck, kg/lb 285-288-301/628-635-664 308-311-324/679-686-714 Wheel base, mm/ft 887/2,91 887/2,91 Track width, front, mm/ft 712/2,34 712/2,34 Track width, rear, mm/ft... -
Page 37: Technical Data
Technical data Cutting unit Combi 103 Combi 112 SD 48 Cutting width, mm/inch 1030 / 41 1120 / 44.1 1220 / 48 Cutting heights, 10 positions, mm/inch 25-75/0.98-2.95 25-75/0.98-2.95 25-75/0.98-2.95 Blade length, mm/inch 388/15.28 420 / 16,5 423 / 16,7 IMPORTANT INFORMATION When the service life of this product has been served and it is no longer used it should be returned to the dealer or to an applicable station for recycling. - Page 40 Original instructions 1154551-95 ´®z+VW,¶6%¨ ´®z+VW,¶6%¨ 2012-05-04...