Alarm Feature "Iii" Programming; Alarm Feature "Iv" Programming; Alarm Feature "V" Programming - Autopage C3-RS-601 Installation Manual

FEATURE "III" PROGRAMMING:
Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
1. Push the Valet switch 3 times (holding in on the 3
the valet switch. You are now in the Alarm feature "A" programming mode.
2. Press and release the transmitter button corresponding to the feature you want to program.
Press One Chirp /
Transmitter LED one pulse
Button Factory Default Setting
20 minutes run time
1.
0.8-second Door lock & Unlock.
2.
Five chirps= 0.8 second lock, dbl 0.8 second unlock
Six chirps= dbl 0.8 second lock, 0.8 second unlock
Door Lock before
3. +
start
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE "IV" PROGRAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 4 times (holding in on the 4
the valet switch. You are now in the Alarm feature "A" programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press One Chirp /
Transmitter LED one pulse
Button Factory Default Setting
Tachometer checking type.
1.
RPM learning
Start Timer:
2.
0.6-second
Low check level
3. +
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE "V" PROGRAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 5 times (holding in on the 5
the valet switch. You are now in the Alarm feature "A" programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press One Chirp /
Transmitter LED one pulse
Button Factory Default Setting
Second Accessory
1.
H3/9 Blue/Black
+ 50 RPM
2.
DBI ONLY
- 50 RPM
3. +
DBI ONLY
RS-603 REV A.
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
rd
push ) until three chirps with one long chirp is heard, then release
Two Chirps /
LED two
pulse
10 minutes
run time
3.5-second
Door
Lock &
Unlock.
Door Lock before & after start *
Door Lock after This is the preferred setting when
start using the optional XT-11 single
button remote
th
push ) until four chirps with one long chirp is heard, then release
Two Chirps /
LED two
pulse
Voltage
checking type
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4
chirps), 1.4-second (5 chirps), 1.6-second (6 chirps),
1.8-second (7 chirps), 2.0-second (8 chirps), 3.0-second (9
chirps), 4.0-second (10 chirps),
Hi check level
th
push ) until five chirps with one long chirp is heard, then release
Two Chirps /
LED two pulse
Second Start
H3/9 Blue/Black
No RPM learning
No RPM Learning or < 50RPM
12
Three Chirps / Four Chirps /
LED three pulse LED four pulse
30 minutes run
5 minutes run time
time
0.8 second lock, 0.8 second dbl
0.35 second lock,0.8 second dbl
unlock unlock
Without this
feature
Three Chirps / Four Chirps / LED four
LED three pulse pulse
Timer checking DBI TACH **
type DATA ONLY !!
Three Chirps / Four Chirps / LED
LED three pulse four pulse
7/9/2008