Yamaha RX10J Owner's Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Offroad Vehicle
  5. RX10J
  6. Owner's manual
Yamaha RX10J Owner's Manual

Yamaha RX10J Owner's Manual

Snowmobile
Hide thumbs
Table of Contents

Advertisement

Quick Links

SNOWMOBILE
OWNER'S MANUAL
RX10J/RX10SJ
RX10MJ/RX10MSJ
RX10RJ/RX10RSJ
RXW10J/RXW10SJ
LIT-12628-02-33
8FA-28199-11

Advertisement

Table of Contents
loading

Related Manuals for Yamaha RX10J

Summary of Contents for Yamaha RX10J

  • Page 1 SNOWMOBILE OWNER’S MANUAL RX10J/RX10SJ RX10MJ/RX10MSJ RX10RJ/RX10RSJ RXW10J/RXW10SJ LIT-12628-02-33 8FA-28199-11...
  • Page 3 Record the frame number, engine number (Primary ID), and key number in the spaces provided for assistance when ordering spare parts from a Yamaha dealer. 1 The frame number is the seventeen-digit number stamped on the frame of the snowmobile. (See fig.
  • Page 4 ESU00011 I NTRODUCTION Congratulations on your purchase of a Yamaha snowmo- bile. This model is the result of Yamaha’s vast experience in the production of fine sporting and touring snowmo- biles. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields.
  • Page 5 PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THE SNOWMO- BILE. NOTE: Yamaha continually seeks advancements in product design and quality. Therefore, while this manual con- tains the most current product information available at the time of printing, there may be minor discrepan- cies between your snowmobile and this manual.

  • Page 6: Table Of Contents

    YAMAHA MOTOR V-belt holders ........5-13 CORPORATION, U.S.A. Storage compartment ....5-13 SNOWMOBILE LIMITED WARRANTY ........1-1 PRE-OPERATION CHECKS....6-1 Fuel ..........6-1 YAMAHA EXTENDED SERVICE Engine oil.........6-2 (Y.E.S.) ..........1-4 Engine oil level ........6-3 Coolant ..........6-4 Throttle lever ........6-5 LOCATION OF THE Throttle override system IMPORTANT LABELS .......2-1...
  • Page 7 Operation on surfaces other than Chassis..........11-2 snow or ice ........7-6 Electric...........11-3 Maximizing drive track life ....7-7 Strap ..........7-8 WIRING DIAGRAM ......12-1 Driving ..........7-9 Stopping the engine.......7-10 Transporting ........7-11 PERIODIC MAINTENANCE ....8-1 Periodic maintenance chart .....8-1 Tool kit ..........8-4 Spark plug inspection ......8-4 Engine idle speed adjustment ..8-6 Throttle cable adjustment ....8-6 Carburetor adjustment.....8-7...

  • Page 8: Yamaha Motor Corporation, U.s.a. Snowmobile Limited Warranty

    ESU00004 Y AMAHA MOTOR CORPORATION, U.S.A. SNOWMOBILE LIMITED WARRANTY CW-01E...
  • Page 9 CW-02E...
  • Page 10 CW-03E...

  • Page 11: Yamaha Extended Service (Y.e.s.)

    Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized • Y.E.S. is designed and administered by Yamaha dealer to get all the facts. He can show Yamaha Motor Corporation to provide maxi- you how easy it is to protect your investment with mum owner satisfaction.

  • Page 12: Location Of The Important Labels

    ESU00007 L OCATION OF THE IMPORTANT LABELS Please read the following labels carefully before operat- ing this snowmobile. NOTE: Maintain or replace safety and instruction labels, as nec- essary. 1 RX10J/RX10S/RX10M/RX10MS 1 RX10R/RX10RS/RXW10/RXW10S...
  • Page 13 4 RX10M/RX10MS 5 RX10M/RX10MS 7 RXW10/RXW10S 8 RX10M/RX10MS/RXW10/RXW10S...

  • Page 14: Safety Information

    1. Read the Owner’s Manual and all labels before oper- ating this snowmobile. Become familiar with all of the operating controls and their function. Consult a Yamaha dealer about any control or function you do not understand. 2. This snowmobile was not manufactured for use on public streets, roads, or highways.
  • Page 15 7. Do not allow anyone to stand behind the snowmobile when starting, inspecting, or adjusting the snowmo- bile. A broken track, track fittings, or debris thrown by the track could be dangerous to the operator or bystanders. 8. Handle fuel with care; it is HIGHLY FLAMMABLE. Never add fuel when the engine is running or hot.
  • Page 16 Fuel may leak out from the fuel breather hose. 2. Modifications made to the snowmobile not approved by Yamaha, or the removal of original equipment may render your snowmobile unsafe for use that may cause severe personal injury. Modifications may also make the snowmobile illegal to use.

  • Page 17: Description

    ESU00012 D ESCRIPTION 1 Windshield 2 Steering handlebar 3 Seat 4 Frame 5 Slide rail suspension 6 Drive track 7 Skis 8 Headlights 9 Shroud 0 Storage compartment RX10/RX10S/RX10R/RX10RS RX10M/RX10MS RXW10/RXW10S...
  • Page 18 A Tail/brake lights B Snow flap C Brake lever D Parking brake lever E Grip warmer adjustment switch F Headlight beam switch G Strap (RX10M/RX10MS) H Engine stop switch I Thumb warmer adjustment switch J Throttle lever K Shift lever (RX10R/RX10RS/RXW10/RXW10S) L Shroud latch M Main switch...

  • Page 19: Control Functions

    ESU00013 C ONTROL FUNCTIONS ESU00362 Main switch The main switch controls the following items. 1 “OFF” The ignition circuit is switched off. The key can be removed only in this position. 2 “ON” The ignition circuit is switched on. 3 “START” The starting circuit is switched on.

  • Page 20: Starter Lever (Choke)

    ESU00020 Starter lever (choke) Use the starter lever (choke) when starting and warming up a cold engine. 1 Starter lever (choke) 2 When starting a cold engine. 3 Warming up 4 When the engine is warm. NOTE: Refer the “Starting the engine” section for proper opera- tion.

  • Page 21: Throttle Override System (T.o.r.s.)

    ESU00023 Throttle override system (T.O.R.S.) If the carburetor or throttle cable should malfunction dur- ing operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the ignition and keep the engine revolution speed between 2,800 and 3,000 r/min if the carburetor fails to return to idle when the lever is released.

  • Page 22: Speedometer Unit

    ESU03900 Speedometer unit The speedometer unit is equipped with the following: a digital speedometer (which shows riding speed) an odometer (which shows the total distance trav- eled) a tripmeter (which shows the distance traveled since it was last set to zero) warning indicators (which show self-diagnosis, cool- ant temperature, fuel level, and oil level warnings) a fuel meter (which shows the fuel remaining in the...

  • Page 23: Fuel Meter And Grip/Thumb Warmer Heat Level Indicator

    ESU03820 Fuel meter and grip/thumb warmer heat level indicator The fuel meter and grip/thumb warmer heat level indica- tor have eight segments 1 which show the amount of fuel remaining in the fuel tank, the heat level of the grip warmer, or the heat level of the thumb warmer.

  • Page 24: Fuel Level Warning Indicator

    (See the table below for warning indicator, warning light and fuel meter segment flash pattern.) When this occurs, have a Yamaha dealer inspect the snowmobile as soon as possible. CA-08E Warning indicator, warning light, and fuel meter segments of the fuel meter flash pattern ·...

  • Page 25: Low Coolant Temperature Indicator Light

    (See the table below for the warning light flash pattern.) When this occurs, have a Yamaha dealer inspect the snowmobile as soon as possible. CA-13E Warning light flash pattern ·...

  • Page 26: Self-Diagnosis Warning Indicator

    The self-diagnosis warning indicator 1 and warning light 2 warn the rider of the above problems by flashing con- tinuously. If necessary, ask a Yamaha dealer for further details. (See page 5-9 for warning indicator and warning light flash patterns.)
  • Page 27 CA-14E Self-diagnosis warning indicator and warning light flash patterns Warning indicator and warning · · · light flash continuously in this 0.75 s pattern. 0.25 s Warning indicator and warning · · · light flash continuously in this 0.75 s pattern.

  • Page 28: Engine Stop Switch

    ESU00031 Engine stop switch The engine stop switch 1 is used to stop the engine in an emergency. Simply push 2 the stop switch to stop the engine. To start the engine, pull 3 the stop switch and proceed with starting the engine. (See page 7-1 for more details.) During the first few rides, practice using the stop switch so that you can react quickly in an emergency.

  • Page 29: Parking Brake Lever

    ESU00035 Parking brake lever When parking the snowmobile or starting the engine, apply the parking brake by moving the brake lever 1 to the left. To release the parking brake, move the parking brake lever 1 to the right. È To apply the parking brake É...

  • Page 30: Headlight Beam Switch

    ESU00039 Headlight beam switch Push the headlight beam switch to change the headlight beam to high or low. 1 Headlight beam switch 2 Push 3 High beam 4 Low beam ESU00048 Shroud latches To open the shroud, unhook the shroud latches, and then slowly raise the shroud forward until it stops.

  • Page 31: V-Belt Holders

    ESU00053 V-belt holders Keep a spare V-belt for emergency use by placing it into the V-belt holders provided. CAUTION : Make sure that the V-belt is installed securely in the holders. ESU00342 Storage compartment The storage compartment is located under the shroud. Open the storage compartment to store the tool kit, spare parts, or other small items.

  • Page 32: Pre-Operation Checks

    ESU00072 P RE-OPERATION CHECKS NOTE: Pre-operation checks should be made each time the snowmobile is used. WARNING The engine and muffler will be very hot after the engine has been run. Avoid touching the engine and muffler while they are still hot with any part of your body or clothing during inspection or repair.

  • Page 33: Engine Oil

    5% of ethanol can be used, although richer jetting may be required to prevent engine dam- age. Consult a Yamaha dealer. Gasohol contain- ing methanol is not recommended. Make sure that snow or ice does not enter the fuel tank when refueling.

  • Page 34: Engine Oil Level

    ESU00344 Engine oil level The engine oil level should be checked before each use. CAUTION : Do not run the engine with too much or not enough oil in the oil tank. Oil could flow into the air filter case and the engine could be damaged.

  • Page 35: Coolant

    ESU00086 Coolant Check the coolant level in the coolant reservoir when the engine is cold. If the coolant level is below the “COLD LEVEL” mark, add soft water until it reaches the “COLD LEVEL” mark. (See pages 8-13–8-14 for more details.) 1 “COLD LEVEL”...

  • Page 36: Throttle Lever

    The T.O.R.S. will operate and the engine should run between 2,800 and 3,000 r/min. WARNING If the engine does not run between 2,800 and 3,000 r/min, stop the engine by turning the main switch to the “OFF” position and consult a Yamaha dealer.

  • Page 37: Brake

    Do not operate the snowmobile if you find any problems in the brake system. You could lose braking ability, which could lead to an accident. Ask a Yamaha dealer to inspect and repair the brake system. CAUTION : Make sure that the brake lever end does not project out over the handlebar end.

  • Page 38: Brake Fluid Leakage

    Apply the brake for a few minutes. Check to see if any brake fluid leaks out from the brake hose joints or the master cylinder. WARNING If brake fluid leakage is found, ask a Yamaha dealer for immediate repairs. CAUTION : Brake fluid may deteriorate painted surfaces or plas- tic parts.

  • Page 39: Drive Track

    ESU00097 Drive track Check the drive track for deflection, wear, or damage. Adjust or replace if necessary. (See pages 8-28–8-30 for more details.) WARNING Do not operate the snowmobile if you find damage to the drive track, or if it has been maladjusted. Drive track damage or failure could result in loss of brak- ing ability and snowmobile control, which could cause an accident.

  • Page 40: Skis And Ski Runners

    Check the handlebar for excessive free play: 1. Push the handlebar up and down and back and forth. 2. Turn the handlebar slightly to the right and left. If excessive free play is noticed, consult a Yamaha dealer. ESU00378 Lights Check the lights.

  • Page 41: Air Filter

    ESU00350 Air filter Always check that no snow is under the air filter element. Remove the air filter case cover and take out the air filter element. If there is any snow under the air filter element, remove the snow. Then install the air filter element beneath the holding guides on the case and install the air filter case cover.

  • Page 42: Operation

    ESU00112 O PERATION ESU00366 Starting the engine WARNING Be sure to check the “SAFETY INFORMATION” section carefully before starting the engine. Make sure that the parking brake is applied. NOTE: Make sure that the engine stop switch is in the on posi- tion.

  • Page 43: Break-In

    CAUTION : After 800 km (500 mi) of operation, the engine oil must be changed and the oil filter cartridge replaced. If any engine trouble should occur during the engine break-in period, immediately have a Yamaha dealer check the snowmobile.

  • Page 44: Riding Your Snowmobile

    totally familiar with the snowmobile’s han- ESU00127 Riding your snowmobile dling and performance characteristics. Getting to know your snowmobile Set the parking brake and follow the A snowmobile is a rider active vehicle, and instructions on pages 7-1–7-2 to start the your riding position and your balance are engine.

  • Page 45: Turning

    Turning Riding uphill For most snow surfaces, “body English” is You should practice first on gentle slopes. the key to turning. Try more difficult climbs only after you have As you approach a curve, slow down and developed your skill. As you approach a begin to turn the handlebar in the desired hill, accelerate before you start the climb, direction.

  • Page 46: Riding Downhill

    Riding downhill downhill leg on the seat and the foot of the uphill leg on the running board. This posi- tion will make it easier for you to shift your body weight as needed. Snow and ice are slippery, so be prepared for the possibility that your snowmobile could begin to slip sideways on the slope.

  • Page 47: Hard-Packed Snow

    Hard-packed snow WARNING It can be more difficult to negotiate on Drive track damage or failure could hard-packed snow as both the skis and result in loss of braking ability and drive track do not have as much traction as snowmobile control, which could cause when the snowmobile is operated on fresh an accident.

  • Page 48: Maximizing Drive Track Life

    Studs may catch on an object and pull out of the track, leaving tears and damage around the already weakened area. To minimize possible dam- age, consult your stud manufacturer for installation and stud pattern recommendations. Yamaha does not recommend track studding.

  • Page 49: Strap

    ESU00245 Strap For RX10M/RX10MS The strap 1 should be used only by experienced opera- tors to assist them when traverse (side-hill) riding. WARNING Improper use of the strap on the handlebar can result in severe injury or death. Use the strap only as an operator grip point when needed to shift weight uphill to maintain balance during traverse (side-hill) riding.

  • Page 50: Driving

    ESU00347 Driving WARNING Be sure to read the “SAFETY INFORMATION” and “Riding your snowmobile” sections carefully before operating the snowmobile. NOTE: Make sure that the engine is warmed up enough before riding. For RX10/RX10S/RX10M/RX10MS 1. Release the parking brake by moving the parking brake lever to the right.

  • Page 51: Stopping The Engine

    CAUTION : Do not shift from “FWD” to “REV” or from “REV” to “FWD” while the snowmobile is moving. Otherwise, the drive system could be damaged. NOTE: The reverse buzzer beeps while the shift lever is in reverse. 2. Release the parking brake by moving the parking brake lever to the right.

  • Page 52: Transporting

    ESU00367 Transporting When transporting your snowmobile on a trailer or in a truck, observe the following recommendations to help protect it from damage: Make sure that the fuel level in the fuel tank is lower than the bottom of the carburetors. Otherwise, the vibration and bumps from the road surface could make it possible for fuel to flow through the carbure- tors into the cylinders.

  • Page 53: Periodic Maintenance

    ∗ Repair if necessary. system (T.O.R.S.) Check operation. Throttle lever 5-2, 6-5 ∗ Repair if necessary. Check for leakage. ∗ Exhaust system Tighten or replace gasket if necessary. ∗ It is recommended that these items be serviced by a Yamaha dealer.
  • Page 54 Check operation. Steering system ∗ Adjust toe-out if necessary. Check for damage. Strap (RX10M/RX10MS) ∗ Replace if necessary. Check operation. Lights 6-9, 8-33 Replace bulbs if necessary. ∗ It is recommended that these items be serviced by a Yamaha dealer.
  • Page 55 Tool kit and recom- Check for proper placement. 6-10 mended equipment ∗ It is recommended that these items be serviced by a Yamaha dealer. NOTE: Brake fluid replacement: 1. When disassembling the master cylinder or caliper cylinder, replace the brake fluid.

  • Page 56: Tool Kit

    NOTE: If you do not have a torque wrench available during a service operation requiring one, take your snowmobile to a Yamaha dealer to check the torque settings and adjust them if necessary. ESU00368 Spark plug inspection The spark plug is an important engine component and is easy to inspect.
  • Page 57 Spark plugs are produced in several different thread lengths. The thread length or reach is the distance from the spark plug gasket seat to the end of the threaded portion. If the reach is too long, overheating and engine damage may result. If the reach is too short, spark plug fouling and poor performance may result.

  • Page 58: Engine Idle Speed Adjustment

    ESU00370 Engine idle speed adjustment CAUTION : Be sure to have a Yamaha dealer make this adjustment. Make sure that the throttle lever moves smoothly. Make sure that the carburetor is synchronized first. 1. Start the engine and warm it up.

  • Page 59: Carburetor Adjustment

    ESU00369 Carburetor adjustment CAUTION : Be sure to have a Yamaha dealer make this adjustment. Make sure that the air filter case is installed dur- ing running to prevent engine damage. Under some operating conditions the carburetor setting may have to be changed due to air temperature changes, elevation changes, use of alcohol oxygenated fuels, etc.,...
  • Page 60 Jet needle adjustment Adjust the jet needle by changing its clip position accord- ing to the setting chart which is available at a Yamaha dealer. Standard jet needle clip 1 position: 3rd groove from upper end CD-03E Clip position Mixture...
  • Page 61 Standard main jet: # 135 CD-04E Main jet 1 Mixture Condition Warm weather Small No. Lean High altitude Cold weather Large No. Rich Low altitude 1. Loosen the carburetor clamps and remove all hoses and cables, and then remove the carburetor. 2.

  • Page 62: High Altitude Adjustments

    If you plan to operate your snowmobile at an altitude different from the area where you bought it, be sure to consult a Yamaha dealer. They can tell you if there are any changes necessary for the altitude where you plan to ride.

  • Page 63: Changing The Engine Oil

    ESU00349 Changing the engine oil It is recommended to have a Yamaha dealer change the engine oil. WARNING Engine oil is extremely hot immediately after the engine is turned off. Coming into contact with or get- ting any engine oil on your clothes could result in burns.
  • Page 64 If oil is leaking or the oil level warning indicator comes on when the engine is running, immediately turn the engine off and have a Yamaha dealer check the snow- mobile. Continuing to operate the engine under such conditions could cause severe engine damage.

  • Page 65: Cooling System

    The cooling system must be bled of air if the coolant reservoir becomes empty, if air can be seen in the cooling system, or if there is a cooling system leak. Consult a Yamaha dealer. CAUTION : Operating the engine with an improperly bled cool- ing system can cause overheating and severe engine damage.
  • Page 66 3. Fill the coolant reservoir with coolant to the “COLD LEVEL” mark. 4. Install the coolant reservoir cap. Check for any cool- ant leakage. NOTE: If you find any leaks, consult a Yamaha dealer. 8-14...

  • Page 67: V-Belt Replacement

    Adjust the V-belt position by removing or adding a spacer 1 on each adjusting bolt. Have a Yamaha dealer make this adjustment. CAUTION : As the V-belt wears, adjustment may be necessary. To ensure proper clutch performance, the V-belt...
  • Page 68 3. Pull 3 the V-belt up over the secondary fixed sheave. 4. Remove the V-belt from the secondary sheave assembly and primary sheave assembly. 5. Put the new V-belt back on the secondary sheave assembly only. Do not force the V-belt between the sheaves;...

  • Page 69: Checking The Oil Level Of The Drive Chain Housing

    8. Install the V-belt over the primary sheave assembly. 9. Rotate the secondary sliding sheave clockwise 6 and push 7 it so that it separates from the secondary fixed sheave. 10. Install the V-belt 8 between the secondary sliding and secondary fixed sheaves. 11.
  • Page 70 3. Remove the dipstick and check that the oil is between the upper and lower levels. If not, add oil to the upper level. 2 Upper level 3 Lower level Drive chain oil:API GL-3 SAE 75 or 80 È For models without reverse transmissions (RX10/RX10S/RX10M/RX10MS) É...

  • Page 71: Checking The Brake Pads

    ESU00174 Checking the brake pads Check the brake pads for wear. If the brake pads reach the wear limit, ask a Yamaha dealer to replace them. 1 Brake pad wear indicator Wear limit a: 1.5 mm (0.06 in) ESU00352 Checking the parking brake pads Check the parking brake pads for wear by measuring the thickness of the pads.

  • Page 72: Checking The Brake Fluid Level

    Water will significantly lower the boiling point of the fluid and may result in vapor lock. If the brake fluid level goes down, consult a Yamaha dealer. CAUTION : Brake fluid may deteriorate painted surfaces or plas- tic parts.
  • Page 73 ESU01910 Ski spring preload adjustment The spring preload can be adjusted by turning the spring preload adjuster 1. For RX10/RX10S/RX10R/RX10RS CD-11E Standard Spring seat length ← → Long Short ← → Preload Hard Soft Maximum Minimum a Length 156.6 mm 148.6 mm 146.6 mm (6.17 in)
  • Page 74 Do not deform or damage the shock absorber in any way. Do not dispose of a worn or damaged shock absorber by yourself. Take the unit to a Yamaha dealer. ESU03240 Rear suspension spring preload adjustment The rear suspension is equipped with two shock absorb- ers.
  • Page 75 The spring preload can be adjusted by turning the spring preload adjuster 3 on the front and rear shock absorb- ers. For RX10/RX10S/RX10R/RX10RS CD-17E Standard Spring seat length ← → Long Short ← → Preload Hard Soft Maximum Minimum È a Length (front) 107.0 mm 97.0 mm 97.0 mm...
  • Page 76 Preload Soft Hard Ë Standard (rear) WARNING Be sure to have a Yamaha dealer make this adjust- ment. This shock absorber contains highly pressurized nitrogen gas. It could explode by improper handling, causing injury, or property damage. Do not tamper with or attempt to open the shock absorber.
  • Page 77 Do not deform or damage the shock absorber in any way. Do not dispose of a worn or damaged shock absorber by yourself. Take the unit to a Yamaha dealer. 8-25...
  • Page 78 Rear suspension full rate adjustment The total suspension spring rate and damping character- istics can be adjusted by changing the installed position of the shock absorber. WARNING Be sure to have a Yamaha dealer make this adjust- ment. CD-07E Installation position Spring rate and...
  • Page 79 ESU00292 Control rod adjustment The weight transfer can be adjusted by turning the con- trol rod adjusting nut 1. 1. Loosen the locknut 2 while holding the control rod adjusting nut 1. 2. To increase weight transfer, turn the adjusting nut in direction a.

  • Page 80: Drive Track Adjustment

    ESU00353 Drive track adjustment WARNING A broken track, track fittings or debris thrown by the drive track could be dangerous to an operator or bystanders. Observe the following precautions: Do not allow anyone to stand behind the snow- mobile when the engine is running. When the rear of the snowmobile is raised to allow the drive track to spin, a suitable stand must be used to support the rear of the snowmo-...
  • Page 81 Drive track adjustment WARNING Be sure to have a Yamaha dealer make this adjustment. Support the snowmobile securely on a suitable stand before working underneath the snowmo- bile. Operate the engine in a well-ventilated area. 1. Lift the rear of the snowmobile onto a suitable stand to raise the drive track off the ground.

  • Page 82: Ski Alignment

    2. Check the following for ski alignment: a. Skis are facing forward. b. Ski toe-out (1 – 2) is within specification. Ski toe-out (1 – 2): 0–15 mm (0–0.59 in) 3. If the alignment is not correct, consult a Yamaha dealer. ESU00354 Handlebar adjustment 1.
  • Page 83 2. Loosen the handlebar bolts. 3. Move the handlebar up or down (± 7°) to adjust the handlebar height to the desired position. È RX10/RX10S/RX10R/RX10RS/RXW10/RXW10S É RX10M/RX10MS CAUTION : Make sure that the projection on the handlebar is not installed into the area a shown. 4.

  • Page 84: Lubrication

    Apply a dab of grease onto the cable end only. Do not grease the throttle cable because it could become frozen, which could cause loss of control. 2 Front suspension 3 Rear suspension WARNING Be sure to have a Yamaha dealer lubricate the front and rear suspensions. 8-32...

  • Page 85: Headlight Bulb Replacement

    ESU00208 Headlight bulb replacement 1. Lift up the shroud. 2. Disconnect the headlight connector. 3. Remove the bulb holder cover. 4. Remove the bulb holder by depressing and turning it counterclockwise. 1 Bulb holder cover 5. Remove the bulb. WARNING Keep flammable products or your hands away from the hot bulb until it cools down.

  • Page 86: Battery

    To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the snowmobile is equipped with electrical accessories.
  • Page 87 5. Replace the blown fuse with one of proper amperage. 6. Install the air filter case by reversing the removal steps. NOTE: If the fuse immediately blows again, ask a Yamaha dealer to inspect the snowmobile. Specified fuses: 4Main fuse: 30 A 5“HEAD”...

  • Page 88: Troubleshooting

    Worn or damaged piston and cylinder No fuel in tank ... Supply fuel..Ask a Yamaha dealer to inspect. Clogged fuel line ... Clean fuel line. Clogged carburetor ... Clean carbure- B. Starting the engine with a dis- tor.
  • Page 89 2. Open the shroud. 5. Connect the other end of the red (+) jumper cable to the positive (+) terminal of the booster battery. 6. Connect the black (-) jumper cable to the negative (-) terminal of the booster battery. 7.
  • Page 90 4. Improper fuel flow ... See A.1 above. NOTE: 5. Incorrect V-belt clutch settings for alti- Make sure that both the red (+) lead and tude or conditions ... Ask a Yamaha the black (-) lead are seated securely in the dealer to inspect. lead holders.
  • Page 91 J. Engine does not upshift or down- shift properly or engages harshly 1. Worn or damaged V-belt ... Replace the V-belt or ask a Yamaha dealer to inspect. 2. Incorrect V-belt clutch settings for alti- tude or conditions ... Ask a Yamaha dealer to inspect.

  • Page 92: Storage

    In areas where oxygenated fuel (gaso- WARNING hol) is used, completely drain the fuel Never smoke around the battery system. Ask a Yamaha dealer if further while it is being charged. Sparks information is needed. may ignite the hydrogen gas created by the battery.
  • Page 93 Yamaha dealer that you have your snowmobile checked charge your battery. and tuned by a Yamaha dealer. They have Do not charge the battery quickly. the experience and training to help you get Charge the battery for 10 hours at the maximum performance and use of your 1.8 amperes.

  • Page 94: Specifications

    ESU00228 S PECIFICATIONS 1 1 - ESU00229 Dimensions CS-01E RX10/RX10S/RX10M/RX10MS/ RX10R/RX10RS/RXW10/RXW10S Overall length 2,755 mm (108.5 in): RX10/RX10S/ RX10R/RX10RS 3,185 mm (125.4 in): RX10M/RX10MS 3,000 mm (118.1 in): RXW10/RXW10S Overall width 1,210 mm ( 47.6 in): RX10/RX10S/ RX10R/RX10RS/ RXW10/RXW10S 1,115 mm ( 43.9 in): RX10M/RX10MS Overall height 1,190 mm ( 46.9 in) Dry weight...
  • Page 95 ESU00231 Chassis CS-03E RX10/RX10S/RX10M/RX10MS/ RX10R/RX10RS/RXW10/RXW10S Drive track and suspension: Track Molded rubber, fiber glass rod reinforced Width 381 mm (15.0 in) Track deflection 25–30 mm (0.98–1.18 in)/ 100 N (10 kg, 22 lb) Length on ground 752 mm (29.6 in): RX10/RX10S/ RX10R/RX10RS 1,071 mm (42.2 in): RX10M/RX10MS 944 mm (37.2 in): RXW10/RXW10S...
  • Page 96 RX10/RX10S/RX10M/RX10MS/ RX10R/RX10RS/RXW10/RXW10S Fuel tank: Tank capacity 38.0 L (8.4 lmp gal, 10.0 US gal) Oil quantity: With oil filter cartridge replacement 3.0 L (2.6 lmp qt, 3.2 US qt) Without oil filter cartridge replacement 2.8 L (2.5 lmp qt, 3.0 US qt) Total amount 3.8 L (3.3 lmp qt, 4.0 US qt) Brake:...
  • Page 97 –MEMO–...
  • Page 98 12-1...
  • Page 99 12-2...
  • Page 100 –MEMO–...
  • Page 101 YAMAHA MOTOR CO., LTD. PRINTED IN JAPAN PRINTED ON RECYCLED PAPER 2003.04 - 2.0×1 CR...

This manual is also suitable for:

Rx10sjRx10rsjRxw10jRx10mjRxw10sjRx10msj ... Show all

Table of Contents