Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Küppersbusch EKI 60.0
Summary of Contents for Küppersbusch EKI 60.0
- Page 1 BEDIENUNGSANWEISUNG mit Montageanweisungen Instructions for use and installation instructions Instructions d’utilisation et avis de montage Gebruiksaanwijzing en montagehandleiding Istruzioni di uso e di montaggio Instrucciones de uso y de montaje Instruções de uso e de montagem EKI 60.0...
-
Page 2: Table Of Contents
Safety instructions ................. 15 Conditions of guarantee Connection and operation ............. 15 The conditions of guarantee applicable for this product are subject to For the hob ..................15 those published by the representative in the relevant country. Details For persons ...................15 regarding same may be obtained from the dealer from whom the appliance was purchased. -
Page 3: Safety Instructions
• Be especially careful to keep the sensor keys clean since soiling could Safety instructions be mistaken for finger contact by the appliance. Never put anything (pans, tea towels etc.) onto the sensor keys! Connection and operation If food boils over onto the sensor keys, we advise you to activate the OFF key. -
Page 4: Appliance Description
Appliance description The decorative design may deviate from the illustrations. 1. Front left induction cooking zone Operating the hob with the touch keys 2. Back left induction cooking zone The glass ceramic hob is operated by means of “touch control” sensor keys which are located at the front of the hob. -
Page 5: Operations
This is how to establish the suitability of a pot: Operations Conduct the magnet test described below or make sure that the pot bears The hob the symbol for suitability for cooking with induction current. Magnet test: The hob is equipped with an induction cooking mode. An induction coil Move the magnet towards the base of your cookware. -
Page 6: Switching On A Cooking Zone
Operations Switching on a cooking zone 1. Press the ON/OFF key until the power setting “0” blinks. 2. Then immediately press the plus key to select the power setting (1...9). The setting can be reduced by pressing the minus key . -
Page 7: Lock /Child Safety Device
Operations Lock /child safety device The lock can be used to block operation and settings (e.g. power setting 4). An activated lock will remain activated even if the hob is switched off! The lock hence also serves as a child safety device in order to prevent the hob from being operated unintentionally or intentionally. -
Page 8: Cleaning And Care
Specific soiling Cleaning and Care Heavy soiling and stains (limescaling and shiny, mother-of-pearl- type stains) can best be removed when the hob is still slightly warm. Use commercial cleaning agents to clean the hob. Proceed as outlined under Item 2. •... -
Page 9: What To Do If Trouble Occurs
Is the power setting blinking? What to do if trouble occurs ? A cooking zone has been switched on and the hob is expecting a suitable pot or pan to be placed on the cooking zone (pan recognition). Only when a pot has been placed on the cooking zone will power be supplied. Interference with and repairs to the appliance by unqualified persons are Is the power setting blinking again, although a pot has dangerous as they can result in electric shock, or short circuit. -
Page 10: Instructions For Assembly
Ventilation Instructions for assembly • The back wall of the cabinet must be open in the area of the cut-out in Note order to provide for air circulation. The KÜPPERSBUSCH induction hob may only be built in in accordance • The front transverse strip of the furniture must be removed so that an to the instructions included in this manual: opening is provided for air flow underneath the worktop over the entire - above an intermediate bottom... - Page 11 Instructions for assembly Dimensions in mm Working surface cut-out Cut out the worktop recess accurately with a good, straight saw blade or recessing machine. The cut edges should then be sealed so that no moisture can penetrate. The area is cut out as illustrated. The glass ceramic hob must have a level and flush bearing.
-
Page 12: Start Of Operation
Start of operation Electrical connection Once the hob has been installed and the power supply has been provided • The electrical connection must be carried out by a qualified (mains connected) an automatic test of the controls will be carried out electrician who is authorised to carry out such work! and information for customer service will be indicated.
Need help?
Do you have a question about the EKI 60.0 and is the answer not in the manual?
Questions and answers