Küppersbusch EKD 10650 Instruction Booklet
  1. Manuals
  2. Brands
  3. Küppersbusch Manuals
  4. Ventilation Hood
  5. EKD 10650
  6. Instruction booklet
Küppersbusch EKD 10650 Instruction Booklet

Küppersbusch EKD 10650 Instruction Booklet

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DE
Bedienungsanleitung
GB
Instructions Booklet
FR
Mode d'emploi
IT
Libretto Istruzioni
Gebruiksaanwijzing
NL
Manual de instrucciones
ES
PT
Manual de instruções
Εγχειρίδιο οδηγιών
GR
EKD 10650
EKD 10650
EKD 10650
EKD 10650
EKD 10650

Advertisement

Table of Contents
loading

Related Manuals for Küppersbusch EKD 10650

Summary of Contents for Küppersbusch EKD 10650

  • Page 1 Bedienungsanleitung Instructions Booklet Mode d’emploi Libretto Istruzioni Gebruiksaanwijzing Manual de instrucciones Manual de instruções Εγχειρίδιο οδηγιών EKD 10650 EKD 10650 EKD 10650 EKD 10650 EKD 10650...
  • Page 2 Dear Customer, If you follow the recommendations contained in this Instruction Manual, your appliance will give you constant high performance and will remain efficient for many years to come. CONTENTS RECOMMENDATIONS AND SUGGESTIONS CHARACTERISTICS INSTALLATION MAINTENANCE...

  • Page 3: Recommendations And Suggestions

    RECOMMENDATIONS AND SUGGESTIONS INSTALLATION • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. • The minimum safety distance between the cooker top and the extractor hood is 650 mm. • Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
  • Page 4 CHARACTERISTICS Dimensions...
  • Page 5 Components Ref. Q.ty Product Components Hood Body, complete with: Controls, Light, Blower, Filters Telescopic Chimney comprising: Upper Section Lower Section Reducer Flange ø 150-120 mm 14.1 Air Outlet Connection Extension Air Outlet Connection Ref. Q.ty Installation Components Hood Connector Support 7.2.1 Upper Chimney Section Fixing Brackets Wall Plugs...

  • Page 6: Installation

    INSTALLATION Wall drilling and bracket fixing Wall marking: • Draw a horizontal line at 650 mm above the hob. 7.2.1 7.2.1 • Place bracket 7.2.1 7.2.1 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit. •...

  • Page 7: Mounting The Hood Body

    Mounting the hood body • Before attaching the hood body, tighten the two screws Vr Vr Vr Vr located on the hood body mounting points. • Hook the hood body onto the screws 12r 12r (4,2 x 12,7). • Fully tighten support screws 12r 12r (4,2 x 12,7).

  • Page 8: Electrical Connection

    ELECTRICAL CONNECTION • Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. Flue assembly Upper exhaust flue Upper exhaust flue Upper exhaust flue Upper exhaust flue Upper exhaust flue • Slightly widen the two sides of the upper flue 7.2.1 7.2.1 and hook them behind the brackets 7.2.1...

  • Page 9: Control Panel

    Control panel L L L L L Light Switches the lighting system on and off. S1 S1 S1 S1 Motor running led. Flashes when the grease filters are saturated. S2 S2 S2 S2 Intensive speed led. Flashes when the activated carbon odour filters are exhausted. M M M M M Motor Switches the extractor motor on and off at low speed.

  • Page 10: Maintenance

    MAINTENANCE Grease filters CLEANING METAL GREASE FILTERS Alarm signal reset Alarm signal reset Alarm signal reset Alarm signal reset Alarm signal reset • Switch of the lights and extractor motor. • Press button V2 V2 for at least 3 seconds, until the leds start to flash.

  • Page 11: Activated Charcoal Filter (Recirculation Version)

    Activated charcoal filter (Recirculation version) REPLACING THE ACTIVATED CHARCOAL FILTER • The filter is not washable and cannot be regenerated. It must be replaced when led S2 S2 S2 flashes or at least every 4 months. The alarm signal will only light up when the extractor motor is switched on.

Table of Contents