Table of Contents
Advertisement
ROC4239
2
4
6
8
10
12
14
16
18
20
22
24
A
B
CR2032
STB
DVD
TV
AUX
1
3
5
7
9
11
13
ROC
15
4239
17
19
21
23
C
1x
21
25
29
33
37
1
41
5
45
9
49
13
53
17
57
61
1x
1x
This universal remote control (4 in 1) is compatible with the majority of television sets, DVD pla-
yers and video recorders, as well as digital boxes such as satellite or cable receivers, DVBT recei-
vers (Digital Video Broadcast Terrestrial), ADSL decoders, and so on.
This remote control was programmed in the factory, so that you can use it to control most of the
sets of the THOMSON group's make. For this reason, we recommend that prior to attempting to
programme the remote control, you try it out by means of one of the methods described in this
user manual. However, fi rst of all, please activate the remote control by removing the 2 protective
tabs from the 2 CR 2032 batteries.
Please keep this guide along with the code list (provided separately), so that you can subsequent-
ly programme your remote control for use with other sets.
corresponds to the type of device, for example: 0603
The keys
for a Thomson satellite receiver) and then to run the
automatic search procedure. The remote control will
1:
On/Standby or Standby only, depending on
then test all the codes automatically until it fi nds those
the equipment being used.
that control the receiver.
2 Mode keys: Select the device to control
(TV, DVD, ...).
Note 2: To control 2 devices of the same type and the
3 Setup: Allows you to program your remote before
same brand (2 Thomson AUXs, 2 Thomson satellite
the fi rst use. It also allows you to access to
receivers, ...) ensure fi rst that these two devices are
secondary functions of certain A/V
not set to react to the same sub code, they will require
appliances (Shift). Press and release the
one sub code for one and a different sub code for
„Setup" key followed by the function key you
the other (i.e., codes A and B with Thomson devices).
want.
Once you have checked this, successively program 2
4 Learn: Used for the learning codes procedure (key
separate mode keys using method D.
copying) (see page 3).
5:
Displays information of the selected
Programming
appliance.
6:
Teletext On.
the remote control
7:
Teletext Off.
Method A – Fast programming
8:
Teletext Hold (stop page scrolling).
with 1-digit subcode
9 Exit:
Turn off the menu of the selected
product.
Before you start programming, you must fi nd the
10 (Mute):
Switches the selected appliance sound
subcode of the set to be controlled. Entering a
off.
subcode lets the remote control test a predefi ned list of
11 Menu: Turns on the menu of the selected
codes. Refer to the list provided with these instructions,
product.
page I of the subcodes.
12 V-, V+:
Increases (+) or decreases (-) the volume
of the selected device.
1. Switch on the set you want to control.
13 P+, P-: Channel Up and Channel Down buttons.
2. Hold down the SETUP key until the key that
14:
Allow you to navigate the menus
corresponds to the last mode you selected blinks
horizontally and verticaly.
and then remains lit (the indicator light remains on
15 OK:
Confi rms a selection.
for a few seconds to give you the time to proceed
16 (play):
Play a DVD disc (DVD)*.
with the following steps. The indicator lamp fl ashes
17:
Fast forward (DVD)*.
to signal that this time is almost up, and then goes
18 (rewind): Goes backward (DVD)*.
off).
19 (pause):
Suspends play and stops on an image*.
3. Press the key that corresponds to the type of
20 (record): To record, press the RECORD key twice.
equipment you want to control:
21 (stop):
Stop the disc (DVD)*.
TV: television set, DVD: DVD player, SAT: satellite
22 Numeric keys 0 - 9: These keys have the same
receiver, cable, DVBT, ADSL, AUX: any other
functions as those of your original
appliance.
remote and are also used to enter the
4. While the indicator is lit, type in the subcode
codes for different products.
(example: 1 for THOMSON).
23 -/--:
In connection with the numeric keys, this
5. Direct the remote control towards the set and try to
button allows you, with some equipment,
switch it off by pressing the key G.
to select directly channels with 2 digits.
6. If the set you want to control switches off, press OK
24 AV:
For selecting an external source (SCART,
to memorise the code.
HDMI, ...).
7. Should the set not switch off, press key G repeatedly,
until the set switches off. Between two key presses,
*
The coloured buttons can be used to select
leave enough time for the key corresponding to the
categories when teletext is activated, and specifi c
selected mode enough time to light up again (about
functions depending on the make.
1 second). Proceeding this way will enable you to
see whether the set responds or not.
8. Immediately upon the switching-off of the set to be
Testing the remote control before
controlled, press OK to store the code.
you programme it
Check of the programming:
1. Turn on the product you want to control.
In principle, your set is ready for receiving the remote
2. Press the Mode key that corresponds to the type of
control commands.
product you want to control:
Check your remote control for proper functioning by
TV: television set, DVD: DVD player, SAT: satellite
performing the test described on page 2.
receiver, AUX: any other equipment.
3. Direct the remote control towards your equipment
Method B – 4-digit codes
and try to switch it off by simply pressing the
programming
key G. If the device does not turn off, you must
program the remote control using one of the
Before you start programming, you must fi nd the code
methods A, B, C or D described hereafter.
of the set to be controlled.
Refer to the list provided with these instructions, page
Note 1: Except for the TV key, the DVD, SAT and AUX
II of the codes.
mode keys can be programmed to control a device
1. Switch on the set you want to control.
other than that indicated on the key. It is therefore
2. Hold down the SETUP key until the key that
possible, for example, to allocate SAT mode to the
corresponds to the last mode you selected blinks
DVD key. You must enter the code corresponding to
and then remains lit (the indicator light remains on
the manufacturer and the device by using one of the
for a few seconds to give you the time to proceed
methods indicated in this manual.
with the following steps. The indicator lamp fl ashes
However, method D (automatic search for a code)
to signal that this time is almost up, and then goes
will greatly simplify the task for you. In this case it
off).
is only necessary to enter a code from the list that
1
A
Hide quick links:
Advertisement
Table of Contents
