Pioneer AVIC-X3 Operation Manual page 140

MAN-AVIC-X3-EN.book Page 138 Wednesday, June 6, 2007 10:15 AM
Message
System detected that the vertical
angle of the installation has been
changed. Learning status for Gyro
Sensor has been initialised.
System detected that the vertical
angle of the installation exceeds the
permission level. Please install the
navigation unit correctly.
Route calculation was not possible.
Route calculation was not possible
because the destination is too far.
Route calculation was not possible
because the destination is too near.
Route calculation was not possible
due to traffic regulations.
Route calculation was not possible
because no guidance can be pro-
vided around the destination or the
starting point.
There is no route to the destination.
Your journey can not avoid the speci-
fied area.
The route could not avoid the speci-
fied area.
Toll road has not been avoided.
Ferry has not been avoided.
Toll road has not been avoided.
There is no applicable data for the
selected city. Automatically returning
to list.
There is no Motorway in this area.
138
When
If the mounting angle of the naviga-
tion unit has been changed.
The navigation system is installed
with an extreme angle exceeding the
limitation of the installation angle.
Route calculation has failed because
of a malfunction of map data, soft-
ware, hardware or disc.
The destination is too far.
The destination or way point(s) are
too close.
• The destination or way point(s) are
in a Control Traffic Zone (CTR) and
the route calculation is hampered.
• Your vehicle is currently in a Con-
trol Traffic Zone (CTR) and the
route calculation is hampered.
The destination, way point(s) or start-
ing point are in an area where no
road exists (e.g. a mountain) and the
route calculation is impossible.
The destination or way point(s) are on
an isolated island, etc. without a ferry
and the route calculation is impossi-
ble.
If route setting cannot avoid speci-
fied Areas to Avoid.
If the route to the destination or way
point(s) cannot be established by
bypassing toll roads (including toll
areas) and Areas to Avoid.
In case a ferry route was included in
the route to the destination or way
point(s) even though "Avoid Ferry"
was set to On.
If the route to the destination or way
point(s) cannot be established by
bypassing toll roads (including toll
areas).
If the history data of the city could
not be used (for example, if the his-
tory data of the city that was used in
the POI Search cannot be found in
the Address Search.)
If no motorway was found in the
selected country.
What to do
The system initialises the sensor in
order to operate it with the maximum
performance and automatically
starts re-learning.
Confirm the installation angle. (The
navigation system must be installed
within the allowed installation angle.
For details refer to Installation Man-
ual.)
• Change the destination.
• Clean the disc.
• Consult the Pioneer Local dealer if
this message persists.
• Set a destination closer to the start-
ing point.
• Set one or more way points.
Set a destination or way point(s) far-
ther from the starting point.
• Set a destination and way point(s)
outside the CTR if you know where
the restricted area is.
• Try a destination or way point(s)
away from the currently set points
to some extent.
• Drive your vehicle to an unre-
stricted area and reset the destina-
tion and way point(s).
• Set a destination and way point(s)
on roads.
• Reset the destination after you
drive the vehicle to any road.
Change the destination.
If the current route is not desired, set
a destination or way point(s) that do
not pass through the Areas to
Avoid.
If the current route is not desired, set
a destination or way point(s) that do
not pass through toll roads (includ-
ing toll areas) and Areas to Avoid.
If the current route is not desired, set
a destination or way point(s) that do
not pass through a ferry route.
If the current route is not desired, set
a destination or way point(s) that do
not pass through toll roads (includ-
ing toll areas).
Once the search is performed to
specify the city, the result is saved as
a history. The data of the specified
city, however, may not be hit by the
different search criteria. In this case,
try another search method or change
the destination.
Set the destination or way points
using another search method or
change the location of the destina-
tion or way point(s).