Lennox MPD-3530CNM-B Installation Instructions Manual page 22

LENNOX HEARTH PRODUCTS • MERIT
HORIZONTAL VENT FIGURES/TABLES (continued)
H 1
Wall Firestop/
Spacer
SV4.5HF**
V
Square termination (SV4.5HT-2) shown.
Figure 41: Rear Vent - TWO 90-DEGREE ELBOWS
H 1
*When using Secure Flex, use
Ceiling Firestop/Spacer SF4.5VF.
**When using Secure Flex, use
Wall Firestop/Spacer SF4.5HF.
Square termination (SV4.5HT-2) shown.
See Table 8 on page 21 as an aid in venting component
selection for a particular range of exterior wall thicknesses.
Figure 42: Top Vent - TWO 90-dEGREE ELBOWS
22
PLUS DIRECT VENT GAS FIREPLACES (MPD33/35/40/45) • INSTALLATION INSTRUCTIONS
®
H
Ceiling
Firestop/Spacer
SV4.5VF*
*When using Secure Flex, use
Ceiling Firestop/Spacer SF4.5VF.
**When using Secure Flex, use
Wall Firestop/Spacer SF4.5HF.
Wall Firestop/Spacer
SV4.5HF**
Wall Firestop/Spacer
SV4.5HF**
Ceiling Firestop/Spacer
SV4.5VF*
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
H
+H
feet
5
10
15
20
Example: If 20 feet of (H) horizontal vent run is needed,
then 4 feet minimum of (V) vertical vent will be required.
This table shows a 1 (V) to 5 (H) ratio. For every 1 foot of
(V) vertical, you are allowed 5 feet of (H) horizontal run,
up to a maximum horizontal run of 20 feet.
See Table 8 on page 21 as an aid in venting component
selection for a particular range of exterior wall thicknesses.
H
V
TABLE H
Maximum H Maximum
1
(meters)
(meters) feet
(1.524)
2 (0.610)
(3.048)
4 (1.219)
(4.572)
6 (1.829)
(6.096)
8 (2.438)
V + H + H 1 = 40 feet (12.2 m) Max.
H = 8 feet (2.438 meters) Max.
H + H 1 = 20 feet (6.096 meters) Max.
TABLE J
H Maximum
+ H
1
feet (meters)
(0.914)
3
(1.524)
5
(3.048)
10
(4.572)
15
20 (6.096)
H
V + + H = 40 feet (12.2 m) Max.
1
H
+ H = 20 ft. (6.096 m) Max.
1
Example: If 20 feet of (H) horizontal vent run
is needed, then 4 feet minimum of (V) vertical
vent will be required.
This table shows a 1 (V) to 5 (H) ratio. For
every 1 foot of (V) vertical, you are allowed 5
feet of (H) horizontal run, up to a maximum
horizontal run of 20 feet.
An elbow is acceptable as 1 foot of vertical
rise except where an elbow is the only vertical
component in the system. See Figure 39.
V Minimum
(meters)
feet
1 (0.305)
2 (0.610)
3 (0.914)
4 (1.219)
V Minimum
(meters)
feet
Elbow Only
1 (0.305)
2 (0.610)
3 (0.914)
4 (1.219)