TABLE OF CONTENTS BEFORE USING THE DRYER PLEASE READ THE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS IDENTIFICATION OF PARTS INSTALLATION INSTRUCTIONS INVERTED WALL MOUNTING STACKING INSTALLATION FRONT VENTING REAR VENTING INSTALL THE FLEXIBLE HOSE OPERATING INSTRUCTIONS CONTROL PANEL OPERATING INSTRUCTIONS CLEANING AND MAINTENANCE TROUBLESHOOTING AND SPECIFICATIONS WIRING CIRCUIT...
IMPORTANT SAFETY INSTRUCTIONS Warning - To reduce the risk of fire, electric shock, or personal injuries, the following basic precautions should be followed: Read all instructions before using this dryer. 2 The interior of the dryer should be cleaned periodically by qualified service personnel.
IMPORTANT SAFETY INSTRUCTIONS contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent - this will reduce, but not eliminate, the hazard. 15 Do not dry unwashed items in the tumble dryer. 16 Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.
IDENTIFICATION OF PARTS Top panel Control panel Program selector Service label Door switch Door airproof strip Door latch Door Exhaust grill Lint filter Model number and Serial number Power supply cord Back plate Air intake grill Outlet cover Warning Read all instructions before using this dryer. This dryer has been designed for domestic use only.
1. The rear of the dryer must not have any restriction to the intake of fresh air. 2. Check the dryer for any damage. If any damage is found do not operate and contact your supplier or Whirlpool Customer Service. 3. The dryer must be kept away from flammable substances.
INSTALLATION INSTRUCTIONS Free standing The dryer stands on the floor and can easily be moved into position. Ensure that it is placed on a level floor. Also ensure there is at least 50 mm air clearance between the back of the dryer and the wall to allow fresh air flow for efficient operation even using the front venting option.
INSTALLATION INSTRUCTIONS 2.Fix the wall hanging brackets to the wall securely (eg. into the stud). If the studs are too far apart, fit a timber slat to the studs then mount the brackets onto the slat. The distance between each is 553 mm as per diagram (Fig.1).
Stacking installation You can use a stacking kit (included as an accessory) if you want to mount your dryer on the top of a Whirlpool front load washing machine, ensure the washer is the same width as the dryer. 1. Remove 4 screws among screws on the bottom panel (see fig.1), and install the stacking kit on the bottom panel (see fig.2).
INSTALLATION INSTRUCTIONS 2. Install the dryer with stacking kit on the top of the front load washing machine (Fig.3). Drill two holes on both sides of washer with 2.9mm diameter drill. Detailed drill position as shown on the stacking kit. Make sure the included screws are used.
INSTALLATION INSTRUCTIONS Change the venting mode There are three venting options: Front venting The exhaust grill has a range of positions, which allows you to select the optimum exhaust air angle. Simply hold the grill and rotate it until you reach the desired position. Note: If the dryer is mounted on the wall you must use the front venting option.
INSTALLATION INSTRUCTIONS INSTALL THE FLEXIBLE HOSE( optional Flexible hose) Connect the narrow end of the connector to the dryer duct pipe Flexible connector mouth at the back of the dryer. Outdoor Then connect the flexible hose to the wide end of the connector. Flexible hose clip Use the clip to fasten connection point between the flexible hose...
CONTROL PANEL A - Start/Pause button After selecting your desired drying program, press this button to start the dryer. To pause the dryer while in operation, press this button again. B - Program control knob Turn this knob to choose the drying program you desire. This dryer has 15 program options available for you to choose.
OPERATING INSTRUCTIONS 3. Selecting programme Turn the program knob to set your desired drying program. a. Sensor Programs When sensor program is selected, dryness of the load will be sensed and dryer will automatically turn itself off while the clothes have dried to the dryness level selected. Approximate Max.
OPERATING INSTRUCTIONS 6. Program completion If the display screen display “0.09”, the program comes into the cool phase. After the program is complete, the dryer will stop tumbling and the display screen will display “End”. Open the door and remove the laundry. If the laundry is not removed, the dryer will automatically commence an "anti-crease"...
CLEANING AND MAINTENANCE WARNING! Unplug the power cord prior to any cleaning Cleaning the surface Wipe off any dust or dirt. Note: Do not use excessive water, a damp cloth is fine. Do not use solvent. Do not use spray cleaners when cleaning the interior. Do not use harsh or abrasive cleaners.
CLEANING AND MAINTENANCE Cleaning the door airproof strip Remove the lint with a soft brush or a wet cloth. Be careful not to damage the airproof strip. Remove any remaining lint from the lint screen on the door at the same time. Note: The door airproof strip must be cleaned before or after each use, or the dryer...
WIRING CIRCUIT Door switch Sensor Thermostat Capacitor Heater Motor Thermal cut-out SPECIFICATIONS TYPE SDRY60 ITEM 220-240)V~ · 50Hz Power supply Maximum operating current (A) Rated load (kg) Drying program 2100 Maximum power (W) 830x560x600 Dimensions (HxDxW) mm Weight (kg) IPX4...
TROUBLESHOOTING GUIDE If a fault occurs, before contacting Whirlpool customer service, make the following checks to try and remedy the problem: Cause Problem Explanation / Suggestion The product may not have been Make sure the power cord is plugged Machine does not...
1. Try to remedy the problem yourself (see “Troubleshooting Guide”). 2. Restart the programme to check whether the problem solved itself. 3. If the dryer machine continues to function incorrectly, call Whirlpool customer service. Specify: The nature of the problem.