Yamaha MOXF6 Manual page 121

PORTAMENTO TIME sets the time it takes for the pitch to reach the next note played when PORTAMENTO
SWITCH is set to on.
PAN position relatively changes according to the preset value for each voice.
EFFECT1 DEPTH controls reverb send level.
EFFECT3 DEPTH controls chorus send level.
HARMONIC CONTENT adjusts the resonance preset for each voice. Setting a value adds to or subtracts from
the center value, 64, since it is an offset parameter.
The larger the value more resonant sound will be produced.
The effective range may be narrower than the range you can designate depending on the selected voice.
The parameters, EG ATTACK TIME, EG DECAY TIME, EG SUSTAIN LEVEL, EG RELEASE TIME adjust the
envelopes preset for each voice. Setting these values add to or subtract from the center value, 64, since these
are offset parameters.
BRIGHTNESS adjusts the cutoff frequency preset for each voice. Setting a value adds to or subtracts from the
center value, 64, since it is an offset parameter. The smaller the value the cutoff frequency will be lowered. The
effective range may be narrower than the range you can designate depending on the selected voice.
Bank Select will be actually executed when the Program Change message is received. Bank Select and
Program Change numbers that are not supported by Yamaha will be ignored.
(3-1-4) PROGRAM CHANGE
STATUS 1100nnnn (CnH)
PROGRAM NUMBER 0ppppppp
(3-1-5) CHANNEL AFTER TOUCH
STATUS 1101nnnn (DnH)
VALUE 0vvvvvvv
(3-1-6) PITCH BEND CHANGE
STATUS 1110nnnn (EnH)
LSB 0vvvvvvv
MSB 0vvvvvvv
Transmitted with a resolution of 7 bits.
(3-2) CHANNEL MODE MESSAGES
STATUS 1011nnnn (BnH)
CONTROL NUMBER 0ccccccc
CONTROL VALUE 0vvvvvvv
(3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0)
All the sounds currently played including the channel messages such as note-on and hold-on in a certain
channel are muted when receiving this message.
(3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0)
Resets the values set for the following controllers.
PITCH BEND CHANGE 0 (center)
CHANNEL AFTER TOUCH 0 (minimum)
MODULATION 0 (minimum)
EXPRESSION 127 (maximum)
BREATH CONTROLLER 127 (maximum)
FOOT CONTROLLER 1 127 (maximum)
FOOT CONTROLLER 2 127 (maximum)
FOOT SWITCH 0 (off)
ASSIGN 1 0 (center)
ASSIGN 2 0 (center)
RIBBON CONTROLLER 0 (center)
ASSIGNABLE FUNCTION 1 0 (off)
ASSIGNABLE FUNCTION 2 0 (off)
SUSTAIN SWITCH 0 (off)
SOSTENUTO SWITCH 0 (off)
RPN Not assigned; No change
Doesn't reset the following data:
PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN, HARMONIC CONTENT, SUSTAIN LEVEL,
RELEASE TIME, ATTACK TIME, DECAY TIME, BRIGHTNESS, EFFECT1 DEPTH, EFFECT3 DEPTH,
PORTAMENTO SWITCH, PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING
(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)
All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain
or Sostenuto is on, notes will continue sounding until these are turned off.
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
Sets VOICE RECEIVE CHANNEL to "OMNI OFF," channel 1.
(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
Sets VOICE RECEIVE CHANNEL to "OMNI ON."
(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0..16)
Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16,
the channel will be Mode 4 (m = 1).
In the Voice mode, the mode can be Mode 2 (m = 1) according to VOICE RECEIVE CHANNEL.
(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode 3.
In the Voice mode, the mode can be Mode 1 according to VOICE RECEIVE CHANNEL.
(3-3) REGISTERED PARAMETER NUMBER
STATUS 1011nnnn (BnH)
LSB 01100100 (64H)
RPN LSB 0ppppppp
MSB 01100101 (65H)
RPN MSB 0qqqqqqq
DATA ENTRY MSB 00000110 (06H)
DATA VALUE 0mmmmmmm
DATA ENTRY LSB 00100110 (26H)
DATA VALUE 0lllllll
First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.
RPN D.ENTRY
LSB MSB MSB LSB PARAMETER NAME
00H 00H mmH --- PITCH BEND SENSITIVITY
01H 00H mmH llH MASTER FINE TUNE
02H 00H mmH --- MASTER COARSE TUNE
7FH 7FH --- --- RPN RESET
RPN numbers will be left not designated.
The internal values are not affected.
n = 0 - 15 CHANNEL NUMBER
p = 0 - 127
n = 0 - 15 CHANNEL NUMBER
v = 0 - 127 AFTER TOUCH VALUE
n = 0 - 15 CHANNEL NUMBER
PITCH BEND CHANGE LSB
PITCH BEND CHANGE MSB
n = 0 - 15 CHANNEL NUMBER
c = CONTROL NUMBER
v = DATA VALUE
n = 0 - 15 CHANNEL NUMBER
p = RPN LSB (Refer to the table as shown below.)
q = RPN MSB (Refer to the table as shown below.)
m = Data Value
l = Data Value
DATA RANGE
00H - 18H (0 - 24 semitones)
{mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}
(-8192*100/8192) - 0 - (+8191*100/8192)
28H - 40H - 58H (-24 - 0 - +24 semitones)
(3-4) NON-REGISTERED PARAMETER NUMBER
There are no applicable parameters.
(3-5) SYSTEM REAL TIME MESSAGES
(3-5-1) ACTIVE SENSING
STATUS 11111110 (FEH)
Transmitted at every 200 msec.
Once this code is received, the instrument starts sensing. When no status nor data is received for over
approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the Sustain
Switch are forcibly turned off. Also, the values of the Controllers are reset to the default settings.
(3-6) SYSTEM EXCLUSIVE MESSAGE
(3-6-1) UNIVERSAL NON REALTIME MESSAGE
(3-6-1-1) GENERAL MIDI MODE ON
F0H 7EH 7FH 09H 01H F7H
(3-6-1-2) IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H
("n" = Device No. However, this instrument receives under "omni.")
(3-6-1-3) IDENTITY REPLY (Transmit only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH mmH 00H 00H 7FH F7H
dd: Device family number
MOXF6: 4CH 06H
MOXF8: 4DH 06H
mm: version
mm = (version no. - 1.0) * 10
e.g.) version 1.0 mm = (1.0 - 1.0) * 10 = 0
version 1.5 mm = (1.5 - 1.0) * 10 = 5
(3-6-2) UNIVERSAL REALTIME MESSAGE
(3-6-2-1) MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Sets the MASTER VOLUME value.
The value "mm" is used to set the master volume (the value "ll" should be ignored).
(3-6-3) PARAMETER CHANGE
(3-6-3-1) NATIVE PARAMETER CHANGE, MODE CHANGE
11110000 F0
01000011 43
0001nnnn 1n
01111111 7F
00011100 1C
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0ddddddd ddddddd
| |
11110111 F7
For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
(3-6-4) BULK DUMP
11110000 F0
01000011 43
0000nnnn 0n
01111111 7F
00011100 1C
0bbbbbbb bbbbbbb
0bbbbbbb bbbbbbb
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0 0
| |
0ccccccc ccccccc
11110111 F7
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Model ID, Start Address, Data
and Check sum itself are added.
(3-6-5) DUMP REQUEST
11110000 F0
01000011 43
0010nnnn 2n
01111111 7F
00011100 1C
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
(3-6-6) PARAMETER REQUEST
11110000 F0
01000011 43
0011nnnn 3n
01111111 7F
00011100 1C
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
MIDI Data Format
Exclusive status
YAMAHA ID
device Number
Group Number High
Group Number Low
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive status
YAMAHA ID
device Number
Group Number High
Group Number Low
Byte Count
Byte Count
Model ID
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive status
YAMAHA ID
device Number
Group Number High
Group Number Low
Model ID
Address High
Address Mid
Address Low
End of Exclusive
Exclusive status
YAMAHA ID
device Number
Group Number High
Group Number Low
Model ID
Address High
Address Mid
Address Low
End of Exclusive
MOXF6/MOXF8 Data List
121