Yamaha MOXF6 Manual page 105

[7] NOISE GATE + COMP + EQ
No. Parameter
1 Comp Attack 1ms – 40ms
2 Comp Release 10ms – 680ms
3 Comp Threshold -48dB – -6dB
4 Comp Ratio 1.0 – 20.0
5 Comp Output Level 0 – 127
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 98.
10 —
11 Noise Gate Attack 1ms – 40ms
12 Noise Gate Release 10ms – 680ms
13 Noise Gate Threshold -73dB – -30dB
14 EQ Mid Frequency 100Hz – 10.0kHz
15 EQ Mid Gain -12dB – +12dB
16 EQ Mid Width 0.1 – 12.0
Insertion L Block
[0] THRU
When this type is selected, no parameters are available.
[1] VOCODER
No. Parameter
1 Formant Shift -2, -1, 0, +1, +2
2 Formant Offset -63 – +63
3 Vocoder Attack 1ms – 200ms
4 Vocoder Release 10ms – 3000ms
5 Gate Switch Off/On
6 Mic Gate Threshold -72dB – -30dB
7 HPF Cutoff Frequency Thru, 500Hz – 16.0kHz
8 HPF Output Level 0 – 127
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 Mic Level 0 – 127
12 Inst Input Level 0 – 127
13 Noise Input Level 0 – 127
14 Output Level 0 – 127
15 BPF1 Gain -18dB – +18dB
16 BPF2 Gain -18dB – +18dB
17 BPF3 Gain -18dB – +18dB
18 BPF4 Gain -18dB – +18dB
19 BPF5 Gain -18dB – +18dB
20 BPF6 Gain -18dB – +18dB
21 BPF7 Gain -18dB – +18dB
22 BPF8 Gain -18dB – +18dB
23 BPF9 Gain -18dB – +18dB
24 BPF10 Gain -18dB – +18dB
Master Effect Block
THRU type is not included in the Master Effect Block. If you wish to bypass this block, turn
the EFFECT [MASTER] button off.
DELAY L, R (Stereo)
LO-FI
COMP DISTORTION
ISOLATOR
DYNAMIC FILTER
SLICE
RING MODULATOR
MULTI BAND COMP
VCM COMPRESSOR 376
Range Value Table No.
(0 – 19) 8
(0 – 15) 9
(79 – 121)
(0 – 7) 10
(0 – 127)
(0 – 19)
(0 – 15)
(54 – 97)
(14 – 54) 3
(52 – 76)
(1 – 120)
Range Value Table No.
(62 – 66)
(1 – 127)
(0 – 29) 8
(0 – 23) 9
(0 – 1)
(55 – 97)
(27 – 58) 3
(0 – 127)
(1 – 127)
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 127)
(46 – 82)
(46 – 82)
(46 – 82)
(46 – 82)
(46 – 82)
(46 – 82)
(46 – 82)
(46 – 82)
(46 – 82)
(46 – 82)
Master EQ Block
[0] MEQ
No. Parameter
1 EQ1 Gain -12dB – +12dB
2 EQ1 Frequency 32Hz – 2.0kHz
3 EQ1 Q 0.1 – 12.0
4 EQ1 Shape Shelving, Peaking
5 EQ2 Gain -12dB – +12dB
6 EQ2 Frequency 100Hz – 10kHz
7 EQ2 Q 0.1 – 12.0
8 —
9 EQ3 Gain -12dB – +12dB
10 EQ3 Frequency 100Hz – 10kHz
11 EQ3 Q 0.1 – 12.0
12 —
13 EQ4 Gain -12dB – +12dB
14 EQ4 Frequency 100Hz – 10kHz
15 EQ4 Q 0.1 – 12.0
16 —
17 EQ5 Gain -12dB – +12dB
18 EQ5 Frequency 500Hz – 16kHz
19 EQ5 Q 0.1 – 12.0
20 EQ5 Shape Shelving, Peaking
When the EQ Shape1 is set to Peaking, the range of EQ Frequency 1 is 63Hz – 2.0kHz (10 – 40).
Effect Parameter List
Range Value Table No.
(52 – 76)
(4 – 40) 3
(1 – 120)
(0 – 1)
(52 – 76)
(14 – 54) 3
(1 – 120)
(52 – 76)
(14 – 54) 3
(1 – 120)
(52 – 76)
(14 – 54) 3
(1 – 120)
(52 – 76)
(28 – 58) 3
(1 – 120)
(0 – 1)
MOXF6/MOXF8 Data List
105