Yamaha MOXF6 Manual page 104

[6] SLICE
No. Parameter
1 Divide Type 16th – 4th
2 Gate Time 0 – 100%
3 Pan AEG Type A – E
4 Pan AEG Min Level 0 – 127
5 Pan Depth -63 –+63
6 Divide Min Level 0 – 127
7 Pan Type A – J
8 Drive 0 – 127
9 AEG Phase 0 – 15 (x 16th note)
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 98.
[7] TECH MODULATION
No. Parameter
1 Mod Speed 0 – 127
2 Mod Depth 0 – 127
3 Mod Gain -12 – +12dB
4 Mod Mix Balance D63>W – D=W – D<W63
5 Pre Mod HPF Cutoff 20Hz – 8.0kHz
Frequency
6 Mod LPF Cutoff Frequency 1.0kHz – 20.0kHz
7 Mod LPF Resonance 1.0 – 12.0
8 Delay Time 0.1 – 740.0ms
9 Delay Time Ofst R 0 – 884
10 Dry/Wet Balance D63>W – D=W – D<W63
11 Feedback Level -63 – +63
12 FB Level Ofst R -63 – +63
13 Feedback Hi Damp 0.1 – 1.0
14 FB Hi Damp Ofst R -0.9 – +0.9
15 —
16 —
Category — MISC
[1] VCM EQ 501
No. Parameter
1 EQ1 (LSH) Frequency 31.5Hz – 2.0kHz
2 EQ1 (LSH) Gain -12.0dB – +12.0dB
3 EQ2 Q 0.50 – 16.00
4 EQ2 Frequency 50.0 Hz – 20.0kHz
5 EQ2 Gain -18.0dB – +18.0dB
6 EQ3 Q 0.50 – 16.00
7 EQ3 Frequency 50.0 Hz – 20.0kHz
8 EQ3 Gain -18.0dB – +18.0dB
9 EQ4 Q 0.50 – 16.00
10 EQ4 Frequency 50.0 Hz – 20.0kHz
11 EQ4 Gain -18.0dB – +18.0dB
12 EQ5 (HSH) Frequency 500Hz – 20.0kHz
13 EQ5 (HSH) Gain -12.0dB – +12.0dB
14 Output Level -12.0dB – +12.0dB
15
16
[2] HARMONIC ENHANCER
No. Parameter
1 HPF Cutoff Frequency 500Hz – 16.0kHz
2 Drive 0 – 127
3 Mix Level 0 – 127
4 —
5 —
6 —
7 —
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
Range Value Table No.
(5 – 11) 13
(0 – 100)
(0 – 4)
(0 – 127)
(1 – 127)
(0 – 127)
(0 – 9)
(0 – 127)
(0 – 15)
(1 – 127)
Range Value Table No.
(0 – 127)
(0 – 127)
(52 – 76)
(1 – 127)
(0 – 52) 3
(34 – 60) 3
(10 – 120)
(1 – 7400)
(0 – 884)
(1 – 127)
(1 – 127)
(1 – 127)
(1 – 10)
(1 – 19)
Range Value Table No.
(12 – 84) 28
(60 – 300)
(0 – 60) 29
(20 – 124) 28
(0 – 360)
(0 – 60) 29
(20 – 124) 28
(0 – 360)
(0 – 60) 29
(20 – 124) 28
(0 – 360)
(60 – 124) 28
(60 – 300)
(60 – 300)
Range Value Table No.
(28 – 58) 3
(0 – 127)
(0 – 127)
[3] Talking Modulator
No. Parameter
1 Vowel a/i/u/e/o
2 Move Speed 1 – 62
3 Drive 0 – 127
4 Output Level 0 – 127
5 —
6 —
7 —
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
[4] DAMPER RESONANCE
No. Parameter
1 HPF Cutoff Frequency 20Hz – 8.0kHz
2 LPF Cutoff Frequency 1.0kHz – 20.0kHz
3 EQ Low Frequency 32Hz – 2.0kHz
4 EQ Low Gain -12 – +12dB
5 Hi Resonance 0.1 – 1.0
6 Pedal Response Slow/Normal/Fast
7 —
8 —
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 —
14 —
15 —
16 Damper Control 0 – 127
[5] PITCH CHANGE
No. Parameter
1 Pitch 1 -24 – +24
2 Fine 1 -50 – +50
3 Initial Delay 1 0.1ms – 400.0ms
4 Feedback Level 1 -63 – +63
5 Pitch 2 -24 – +24
6 Fine 2 -50 – +50
7 Initial Delay 2 0.1ms – 400.0ms
8 Feedback Level 2 -63 – +63
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 Pan 1 L63 – C – R63
12 Output Level 1 0 – 127
13 Pan 2 L63 – C – R63
14 Output Level 2 0 – 127
15 —
16 —
[6] EARLY REFLECTION
No. Parameter
1 Type S-hall, L-hall, Random,
Reverse, Plate, Spring
2 Room Size 0.1 – 20.0
3 Diffusion 0 – 10
4 Initial Delay 0.1ms – 200.0ms
5 Feedback Level -63 – +63
6 HPF Cutoff Frequency 20Hz – 8.0kHz
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz
8 —
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 Liveness 0 – 10
12 Density 0 – 3
13 Feedback High Damp 0.1 – 1.0
14 —
15 —
16 —
Effect Parameter List
Range Value Table No.
(0 – 4)
(1 – 62)
(0 – 127)
(0 – 127)
Range Value Table No.
(0 – 52) 3
(34 – 60) 3
(4 – 40) 3
(52 – 76)
(1 – 10)
(0 – 2)
(1 – 127)
(0 – 127)
Range Value Table No.
(40 – 88)
(14 – 114)
(0 – 127) 7
(1 – 127)
(40 – 88)
(14 – 114)
(0 – 127) 7
(1 – 127)
(1 – 127)
(1 – 127)
(0 – 127)
(1 – 127)
(0 – 127)
Range Value Table No.
(0 – 5)
(0 – 127) 6
(0 – 10)
(0 – 127) 5
(1 – 127)
(0 – 52) 3
(34 – 60) 3
(1 – 127)
(0 – 10)
(0 – 3)
(1 – 10)
MOXF6/MOXF8 Data List
104