Rf Exposure; Fcc Compliance - AT&T MicroCell User Manual

AT&T 3G MicroCell User Guide | Other

RF Exposure

NOTE: This transmitter must not be
collocated or operated in conjunction
with any other antenna or transmitter.
This equipment should be installed and
operated with a minimum distance of 7.9
inches (20 cm) between the radiator and
your body.
United States
This equipment complies with FCC
RF exposure limits set forth for an
uncontrolled environment. This system
has been evaluated for RF exposure
for humans in reference to ANSI C 95.1
(American National Standards Institute)
limits. The evaluation was based on
evaluation per ANI C 95.1 and FCC OET
Bulletin 65C rev 01.01. The minimum
separation distance from the antenna/
radiator to a general bystander is 7.9
inches (20 cm) to maintain compliance.
This transmitter must not be collocated
or operating in conjunction with any other
antenna or transmitter.
The availability of some specifi c channels
and/or operational frequency bands are
country dependent and are fi rmware
programmed at the factory to match the
intended destination. The fi rmware setting
is not accessible by the end user.
Canada
This equipment complies with IC
RF exposure limits set forth for an
uncontrolled environment. This system
has been evaluated for RF exposure for
humans in reference to Canada Health
Code 6 (2009) limits. The evaluation was
based on evaluation per RSS-102 Rev 4.
The minimum separation distance from
the antenna to general bystander is 7.9
inches (20 cm) to maintain compliance.
26

FCC Compliance

United States FCC Compliance
This device has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against such
interference in a residential installation.
This equipment generates, uses, and
can radiate radio frequency energy. If not
installed and used in accordance with
the instructions, it may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment OFF and ON, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
» Reorient or relocate the receiving
antenna, if applicable.
» Increase the separation between the
equipment and receiver.
» Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
» Consult the service provider or an
experienced radio/television technician
for help.
Any changes or modifi cations not
expressly approved by Cisco Systems, Inc.,
could void the user's authority to operate
the equipment.
The information shown in the FCC
Declaration of Conformity paragraph
below is a requirement of the FCC and is
intended to supply you with information
regarding the FCC approval of this device.
The phone numbers listed are for FCC
related questions only and not intended
for questions regarding the connection or
operation for this device. Please contact
your service provider for any questions
you may have regarding the operation or
installation of this device.
Declaration of Conformity
This device complies with Part 15 of FCC
Rules. Operation is subject to the following
two conditions: 1) the device may not cause
harmful interference, and 2) the device
must accept any interference received,
including interference that may cause
undesired operation.
AT&T 3G MicroCell™
Model: MicroCell
Manufactured by: Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 770-236-1077
Canada EMI Regulation
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la class B est
conforme à la norme NMB-003 du Canada.
This device complies with RSS-132 and
RSS-133 of the Industry Canada Rules.
Operation is subject to the following two
conditions:
» This device may not cause harmful
interference.
» This device must accept any interference
received, including interference that may
cause undesired operation.
20100527 FCC Standard
Software Use
The software incorporated in your
device is protected by copyright law
and furnished to you under a license
agreement. You may only use or copy this
software in accordance with the terms of
your license agreement. In connection
with your purchase of this product you
were offered a copy of the Software End
User License Agreement, including open
source licenses and notices. If you would
like to have additional copies of this
document please go to: http://www.att.com/
MicroCellEndUserLicense.
Disclaimer
Cisco Systems, Inc. assumes no
responsibility for errors or omissions that
may appear in this guide. We reserve the
right to change this guide at any time
without notice.
27