Hall Adjustment - Sony DCR-TRV9 Service Manual

3. HALL Adjustment

For detecting the position of the lens iris, adjust the hall AMP gain
and offset.
Subject Not required
Measurement Point DDS display data of LCD or TV
Measuring Instrument monitor (Note 3)
Adjustment Page F
Adjustment Address 1E, 1F
Specified Value 80 to 82 during IRIS OPEN (Note 1)
13 to 17 during IRIS CLOSE (Note 2)
Note 1: Select page: 6, address: 01, set data: 01, and press the PAUSE
button of the adjustment remote commander.
Note 2: Select page: 6, address: 01, set data: 03, and press the PAUSE
button of the adjustment remote commander.
Note 3: DDS display data of LCD or TV monitor.
CA 00 00XX
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 11, set data: 02, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 6, address: 00, and set data: 01.
4) Select page: 6, address: 04, and set data: 03.
5) Select page: 6, address: 01, set data: 03, and press the PAUSE
button.
6) Select page: F, address: 1F, set data: 40, and press the PAUSE
button.
7) Select page: F, address: 1E, set data: 40, and press the PAUSE
button.
8) Read the DDS display data (the bottom two digits of the display
data at the bottom right of the LCD display or the TV monitor),
and this data is named K
2
9) Select page: F, address: 1E, set data: 30, and press the PAUSE
button.
10) Read the DDS display data, and this data is named K
11) Select page: 6, address: 01, set data: 01, and press the PAUSE
button.
12) Read the DDS display data, and this data is named W
13) Select page: F, address: 1E, set data: 40, and press the PAUSE
button.
14) Read the DDS display data, and this data is named W
15) Convert W , W , K , K , to decimal notation, and obtain W
1 2 1 2
W ' , K ' , K '. (Refer to "Hexadecimal-decimal Conversion
2 1 2
Table". of "5-4. Service mode".)
16) Calculate X ' using the following equations (decimal notation
1
calculation).
A'= W ' + K ' – W ' – K ' ....................................... Equation 1
2 1 1 2
B'= W1' – K1' ........................................................ Equation 2
X '=[1728 + (48 A') – (16 B')]/A' ................... Equation 3
1
17) Convert X ' to hexadecimal notation, and obtain X
1
(Round off to one decimal place)
18) Select page: F, address: 1E, set data: X
button.
19) Select page: 6, address: 01, and set data: 03, and press the
PAUSE button.
20) Select page: F, address: 1F, change the data and adjust the DDS
display data to "15".
21) Press the PAUSE button of the adjustment remote commander.
22) Select page: 6, address: 01, and set data: 01, and press the
PAUSE button.
Object data
.
.
1
.
1
.
2
.
1
, and press the PAUSE
1
23) Read the DDS display data, and this data is named W
lies within the "80" to "82" range, perform "Processing after
completing adjustments". If it is lies outside the range, perform
the following adjustments.
24) Convert W to decimal notation, and obtain W
0
25) Calculate X ' using the following equations (decimal notation
2
calculation).
C'= W – B'–23 ...................................................... Equation 4
0
X '=[(108 – B')
2
(X ' and B' are values obtained from equations 2) and 3) )
1
26) Convert X ' to hexadecimal notation, and obtain X
2
off to one decimal place)
27) Select page: F, address: 1E, set data: X
button.
28) Select page: 6, address: 01, set data: 01, and press the PAUSE
button.
29) Select page: F, address: 1F, change the data and adjust the DDS
display data to "81".
30) Press the PAUSE button of the adjustment remote commander.
31) Select page: 6, address: 01, set data: 03, and press the PAUSE
button.
32) Check the DDS display data lies within the "13" to "17" range.
' ,
Processing after Completing Adjustments
1
1) Select page: D, address: 11, and set data: 00, and press the
PAUSE button.
2) Select page: 0, address: 01, and set data: 00.
3) Select page: 6, address: 01, and set data: 00, and press the
PAUSE button.
4) Select page: 6, address: 04, and set data: 00.
5) Select page: 6, address: 00, and set data: 00.
5-10
'.
0
(X ' – 48) + (48 C')]/C' .......... Equation 5
1
, and press the PAUSE
2
. If W
0 0
. (Round
2