User Manual for your Baumatic BTI9170GL Cooker Hood 90 cm Glass island cooker hood in stainless steel NOTE : This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference;...
Contents Page Environmental note IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your cooker hood Using your Baumatic cooker hood 9 - 10 Before first use To use your cooker hood 9 – 10 Setting the time of day The timer...
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line.
Page 6
o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type.
Page 7
o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed. o Note that it removes odours from your room, not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs.
Specifications of your cooker hood Congratulations on purchasing a Baumatic cooker hood! PRODUCT DIMENSIONS Height: 665 mm * – 1165 mm Width: 900 mm Depth: 600 mm DIMENSIONS OF CHIMNEY SECTION 270 mm x 285 mm o High extraction tangential motor...
To use your cooker hood o Make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s installation instructions. o Find the control panel, which is located in the middle of the canopy.
o Press the light button to switch the bulbs on and off. You can switch the lights on, even if the hood is not operating. IMPORTANT: IDEALLY YOU SHOULD SWITCH ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK, OR AT THE VERY LEAST WHEN YOU BEGIN COOKING.
Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABL E. Cleaning o Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth.
aintenance Removing and cleaning the grease filters o First remove the grease filters by pulling down on the handle and pulling them away from the cooker hood. o Soak the grease filt ers in hot water and washing up liquid for about an hour.
Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE TH AT YOU HAVE DISCONNECTED TH E COOKER HOOD FROM YOUR MAINS SUPPLY. o Remove the grease filters (as described on page 12). o Prior to touching the light bul bs ensure that they have cooled down.
itting the carbon filter the appliance is being used to be used in recirculation mode then it is necessary to fit carbon filt ers. This will help to absorb unpleasant dours caused by cooking. IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE T HE CARBON FILTER, YOU MUST ENSURE THAT...
Page 15
3) Use a screwdriver to ke out the two screws at go through the fixing point and then lower the carbon filter over the motor casing hole. o The corner with diagonal cut-ou t on it, must be positioned against the fixing point (as shown in the above...
Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The ra ting plate can be found behind the grease filter.
o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the terminal marked “N” (ne utral), or coloured black.
o Do not tile, grout or silicone this appliance to the ceiling. This appliance is designed to be surface mounted only. o Remove any protective wrapping that has been put on the cooker hood or chimney sections, to protect them during transit. Positioning Height of the appliance Total height of the kitchen...
IMPORTANT: Your ceiling should have a minimum height of 2.7 metres, othe rwise yo u may encounter difficulties when installing the appliance. MPORTANT: Although the minimum height of the ppliance can be set at 665 mm. During the installation process you will need to move the lower chimney sec tion upwards, to allow you to attach the main body of the hoo to the framework.
Supplied installation components 1) Position the hanging plate on the eiling and then mark the position of the screw holes. o The han ging plate should be securely fixed to the ceiling, using the 12 x ST6 (40 mm) screws o Depending on the surface of the ceiling that you are fixing the hanging plate to, you may need to use 8 x expansion bolts (for...
Page 21
2) Fix the angle bars to the hanging plate, sing the 8 x M4 nuts and bolts with metal washers. 3) Extend the angle bars to the required height nd then fix them in position using the 16 x M4 nuts and bolts with metal washers.
Page 22
5) If you are going to be using the hood in xtraction mode, you should fit the spigot for the duct hose onto the main body of the cooker hood, using the 4 x M4 bolts, ) If the glass canopy has not been pre- ssembled by the factory, then it should be fixed to the top of the main body of the cooker hood at this stage.
o Remove the hanging hook and then slide the lower chimney section downwards, until it rests against the ma in body of the cooker hood. o Use a stainless steel cleaner and polish on the stainless steel sections of the appliance. o If you are using the applia nce in recirculation mode, then you should now fit the carbon filter.
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before con tacting Baumatic Customer Care, please efer to the checklist below. My cooker hood will not start. o Ch ck that the hood is connected to th e electricity supply o Check that the fan speed control is set correctly.
Page 25
Or any installation other han the one specified by Baumatic Ltd. has been completed. Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance.
Need help?
Do you have a question about the BTI9170GL and is the answer not in the manual?
Questions and answers