GE TRIVECTION JT930 Installation Instructions Manual
30” built-in wall oven
Hide thumbs
Also See for TRIVECTION JT930:
- Owner's manual (48 pages) ,
- Installation instructions manual (16 pages) ,
- Service manual (4 pages)
Table of Contents
Advertisement
Quick Links
Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
•
instructions for local inspector's use.
IMPORTANT
•
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires basic mechanical and advanced
electrical skills.
• Completion time – 1 to 3 hours
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation
is not covered under the Warranty.
WARNING
be properly grounded.
ATTENTION INSTALLER
•
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT
permitted on these products.
31-10663
1-07 JR
JT930, JT980, ZET3038, ZET3058
— Save these
— Observe all
— This appliance must
30" Built-In Trivection
Wall Oven
FOR YOUR SAFETY:
• Be sure your oven is installed properly by a
qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall coverings
around the oven can withstand the
temperatures (up to 200°F) generated
by the oven.
WARNING:
the oven supply line must be shut off while
line connections are being made. Failure to
do so could result in serious injury or death.
• To prevent damage to the door and to
prevent excessive microwave leakage, do
NOT remove the door on the single wall
oven or the upper oven door on the double
wall oven.
1
™
The electrical power to
Advertisement
Table of Contents
Related Manuals for GE TRIVECTION JT930
Summary of Contents for GE TRIVECTION JT930
-
Page 1: Installation Instructions
Installation Instructions Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT • — Save these instructions for local inspector’s use. IMPORTANT • — Observe all governing codes and ordinances. -
Page 2: Prepare To Install The Oven
PREPARE TO INSTALL THE OVEN TOOLS YOU WILL NEED Drill with 1/8” Bit (Extension may be required) Adjustable Wrench (for 1-7/16” Nut) Phillips Screwdriver Tape Measure Hand or Sabre Saw MATERIALS YOU MAY NEED Strain Relief Junction Box Clamp for 1/2” conduit 60”... -
Page 3: Pre-Installation
Installation Instructions PRE-INSTALLATION All installation information on the following pages is to be used for SINGLE and DOUBLE oven installation! Remove packaging materials. Check behind hinges. Remove plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad. - Page 4 SINGLE BUILT-IN OVEN CUTOUT OPTIONS CUTOUT OPTIONS FOR SINGLE BUILT-IN OVENS Skip to Step 3 for Double Built-In Oven models. There are 4 installation options for single built-in ovens. Choose the appropriate one for your application: WALL MOUNT—SINGLE BUILT-IN OVEN OPTION WALL MOUNT—SINGLE BUILT-IN OVEN BELOW AN ADVANTIUM ™...
- Page 5 This separation will provide clearance for bottom overlap of the Advantium oven and top overlap of the single wall oven. • If you are replacing a GE/Monogram electric double oven with the combined installation of an Advantium and single wall oven, the middle rail separating the two openings may need to be larger than the 2”...
- Page 6 SINGLE BUILT-IN OVEN CUTOUT OPTIONS UNDER COUNTER—SINGLE BUILT-IN OVEN OPTION 25” Top and/or side fillers may be necessary if unit is positioned between existing cabinets. Be sure they are attached securely, since they will anchor the oven in the cabinet. NOTE: This oven is not approved to be installed under a cooktop.
-
Page 7: Cutout For Double Built-In Oven
DOUBLE BUILT-IN OVEN CUTOUT CUTOUT FOR DOUBLE BUILT-IN OVEN Cutout Width 28 1/2” Min 28 5/8” Max. All corners must be cut square Allow 11/16” for overlap of Opening oven over between side edges inside of cutout walls must be at Least Allow a 28 1/2”... - Page 8 REMOVE THE LOWER OVEN DOOR ON DOUBLE WALL OVEN MODELS ONLY To prevent damage to the door and to prevent excessive microwave exposure, do NOT remove the door on the single wall oven or the upper oven door on the double wall oven. NOTE: The oven door is heavy.
-
Page 9: Electrical Connections
ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating Plate is located on oven frame.) Rating plate location We recommend you have the electrical wiring... - Page 10 ELECTRICAL CONNECTIONS TURN OFF ELECTRICITY Turn off the circuit breaker or remove fuses to the oven branch circuit. CONNECT CONDUIT With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
-
Page 11: Three-Conductor Branch Circuit Connection
Installation Instructions THREE-CONDUCTOR BRANCH CIRCUIT CONNECTION When connecting to a three-conductor branch circuit, if local codes permit: Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut. Junction Box Cover Connect the oven red lead to the branch circuit red lead in accordance with local... - Page 12 SECURE THE OVEN IN THE OPENING SLIDE THE OVEN INTO THE OPENING Loop (do not tie) the correct length of string around the conduit before the oven is slid into place. This will keep the conduit from falling improperly behind the oven.
- Page 13 To install a single metal bottom trim assembly (on some models), see Step 11. To install a metal bottom trim with a plastic bottom trim (on some models), see Steps 11 and 12. INSTALL THE METAL BOTTOM TRIM With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening.
- Page 14 REPLACE THE LOWER OVEN DOOR ON DOUBLE WALL OVEN MODELS ON DOUBLE WALL OVEN MODELS, REPLACE THE LOWER DOOR: Firmly grasp both sides of the door at the top. Hinge arm Bottom edge of slot Indentation With the door at the same angle as the removal position, seat the indentation of the hinge arm into the bottom edge of the hinge slot.
-
Page 15: Final Checklists
FINAL CHECKLISTS PRE-TEST CHECKLIST Remove all protective film. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see Steps 11 and 12). Check to be sure the mounting screws are installed and flush with the side trim (see Steps 9 and 10). - Page 16 Printed in the United States...