Table of Contents
Advertisement
Adjusting the Parametric Equalizer Curve
(P-EQ)
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
Setting item: P-EQ
1
Select L+R by touching [ ] of P-EQ.
When graphic EQ is set to L+R, this setting will be turned off.
2
Touch [
] of P-EQ after selecting L+R.
The P-EQ list screen appears.
3
Adjust the P-EQ to your preference.
Adjusting the Band
Touch [
] or [ ] of BAND to select the band to be
adjusted.
BAND 1 / BAND 2 / BAND 3 / BAND 4 / BAND 5
Adjusting the Frequency
Touch [
] or [ ] of FREQ. to adjust the frequency of the
selected band.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
Band-1: 20 Hz~80 Hz (63 Hz)
Band-2: 50 Hz~200 Hz (150 Hz)
Band-3: 125 Hz~3.2 kHz (400 Hz)
Band-4: 315 Hz~8 kHz (1 kHz)
Band-5: 800 Hz~20 kHz (2.5 kHz)
Adjusting the Level
Touch [
] or [ ] of LEVEL to adjust the level of selected
band.
Adjustable level: –6 to +6 dB
Setting the Bandwidth
Touch [
] or [ ] of Q. to select the bandwidth.
Adjustable bandwidth: 1, 1.5, 3
4
To adjust another band, repeat step 3 and adjust all
bands.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
• When the parametric EQ is adjusted, the adjustment for graphic EQ
becomes ineffective.
Equalizer Presets (F-EQ)
10 typical equalizer settings and 6 user's preset setting are preset at the
factory for a variety of musical source material.
Setting item: F-EQ
1
Touch [
] of F-EQ.
The F-EQ setup screen appears.
2
Touch [ ] or [ ] of the desired type to set to ON.
Flat / Pops / Rock / News / Jazz&Blues / Electrical Dance /
Hip Hop&Rap / Easy Listening / Country / Classical / User1 /
User2 / User3 / User4 / User5 / User6
• Only one type can be set to ON.
• By selecting User's 1 to 6, you can recall the stored preset number in
"Adjusting the Graphic Equalizer Curve (G-EQ)" (page 52) or
"Adjusting the Parametric Equalizer Curve (P-EQ)" (page 53) .
Setting the Response Slope for the High
Range Speaker (TW SETUP)
Depending on the response characteristics of the speaker, care should be
taken when setting the response slope of the high range speaker to
FLAT in 2.2ch (3WAY) mode (see "Adjusting the Crossover Settings
(X-OVER)" on page 51), as speaker damage may result.
Setting item: TW SETUP
Touch [ ] or [ ] of TW SETUP to select Factory's or User's.
Factory's: As protection from possible speaker damage, FLAT
cannot be set for the response slope of the high
range speaker in 2.2ch (3WAY) mode.
User's:
The FLAT setting is possible in 2.2ch (3WAY) mode.
• The TW Setup mode can only be selected if the FRONT/REAR/
SUBW. (4.2CH)/3WAY (2.2CH) switch on the IMPRINT audio
processor (PXA-H100) is set to 3WAY (2.2CH).
Storing Settings in the Memory
Adjustment or setting contents of X-OVER, T.CORR and P/G-EQ can
be stored.
Contents that can be stored vary depends on the IMPRINT audio
processor used.
1
Check whether the Defeat mode is off.
2
Touch [MEMORY] on the A.PROCESSOR list
display.
3
Within 5 seconds, touch any one of the preset
buttons [P.SET 1] through [P.SET 6] on the
A.PROCESSOR list screen.
The setting contents are stored.
• The stored contents will not be deleted even when the battery power
cord is detached.
• This operation cannot be performed when a typical equalizer setting
(e.g. pops) is selected in "Equalizer Presets (F-EQ)" (page 53).
53
-EN
Hide quick links:
Advertisement
Table of Contents
