Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Dynex Manuals
  4. TV Mount
  5. DX-DRTVM112
  6. Safety information manual

Dynex DX-DRTVM112 Safety Information Manual

Low-profile tv wall mount
Hide thumbs Also See for DX-DRTVM112:

Advertisement

Quick Links

Download this manual
DX-DRTVM112
Low-Profile TV Wall Mount
For either wood-stud or
concrete wall installations
Before using your new product, please read these instructions to prevent any damage.
A S S E M B LY G U I D E
Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . .3
Package contents . . . . . . . . . . . . . . . . . . . . .4
Installation instructions. . . . . . . . . . . . . . . .5

Advertisement

loading
Need help?

Need help?

Do you have a question about the DX-DRTVM112 and is the answer not in the manual?

Questions and answers

Related Manuals for Dynex DX-DRTVM112

Summary of Contents for Dynex DX-DRTVM112

  • Page 1 A S S E M B LY G U I D E DX-DRTVM112 Low-Profile TV Wall Mount Safety information and specifications . .2 Tools needed......3 Package contents .

  • Page 2: Safety Information And Specifications

    We’re here for you doubts about the safety of the installation, contact Customer Service or www.dynexproducts.com call a qualified contractor. Dynex is not For customer service, call: responsible for damage or injury caused 1-800-305-2204 (U.S. and Canada) or by incorrect installation or use.

  • Page 3: Tools Needed

    DX-DRTVM112 Tools needed You will need the following tools to assemble your new TV wall mount: ardware Level Pencil Drill 1/8" (3 mm) wood drill bit for wood stud wall Edge-to-edge stud 3/8" (10 mm) masonry Socket wrench with 7/16"...

  • Page 4: Package Contents

    Package contents Make sure that you have all of the hardware necessary to assemble your new TV wall mount: A TV Bracket (1) B Wall Plate (1) C Bracket Extensions (2) D Wall mount template (1) DX-TVM111 Template • Gabarit • Plantilla Haut Parte superior Tools Needed...

  • Page 5: Installation Instructions

    DX-DRTVM112 Installation instructions STEP 1 - Determining the hole pattern on your TV Carefully place your TV screen face down on a cushioned, clean surface to protect the screen from damage and scratches. If your TV has a table top stand attached, remove the stand. See the documentation that came with your TV for instructions.
  • Page 6 STEP 2 - Determine whether your TV has a flat, irregular, or obstructed back Temporarily lay the TV bracket (A) and adapters (C), if necessary, on the back of your TV. Align the screw holes in the TV bracket with the mounting screw holes on your TV. Identify which type of back your TV may have: •...
  • Page 7 DX-DRTVM112 STEP 3 - Select screws and spacers Select the hardware for your TV (screws and spacers). A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back of the TV.)
  • Page 8 STEP 4 - Option 1: Attaching the mounting hardware to TVs with a flat back Align the TV bracket (A) with the screw holes on the back of the TV. Install washers (G ), and screws (E) into the holes in the back of the TV. Tighten the screws until they are snug against the TV bracket.
  • Page 9 DX-DRTVM112 STEP 4 - Option 2: Attaching the mounting hardware to TVs with irregular or obstructed backs Align the TV bracket (A) with the screw holes on the back of the TV. Place spacers (H) behind the TV bracket and the washers (G) over the holes in the TV bracket, then insert the screws (F) through the washers, TV bracket, and spacers.
  • Page 10 STEP 5 - Determine wall-mount location Notes: • For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder • Your TV should be high enough so your eyes are level with the middle of the screen. Normally, the center of your TV should be 40 to 60 inches (100 to 150 cm) above the floor.
  • Page 11 DX-DRTVM112 STEP 6 - Option 1: Installing on a wood stud* wall Note: Any drywall covering the wall must not exceed 5/8" (16 mm). Locate the stud. Verify the center of the stud with an edge-to-edge stud finder. Align the wall plate template (D) at the height you determined in the previous step and make sure that it is level.
  • Page 12 STEP 6 - Option 2: Installing on a solid concrete* or concrete block wall CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount the wall plate directly onto the concrete surface. Align the wall plate template (D) at the height you determined in the previous step and make sure that it is level.
  • Page 13 DX-DRTVM112 STEP 7 - Mounting the TV to the wall plate Place the TV bracket (A) into the slotted flanges of the wall plate (B). The TV can be mounted either (1) vertically, or (2) with a 6° tilt. Lock the TV and bracket assembly to the wall plate by rotating the lock into the flange slot.
  • Page 14 STEP 8 - Removing the TV from the wall plate and disassembling the wall mount Unlock the TV and bracket assembly from the wall plate by rotating the lock out of the flange slot. Lift the TV bracket (A) from the slotted flanges of the wall plate (B) and place it on a cushioned, clean surface to protect the screen from damage and scratches.
  • Page 15 7601 Penn Ave. South, Richfield, MN 55423 U.S.A. © 2013 BBY Solutions, Inc. All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.